Table of Contents
Advertisement
Section 6: Specifications & Capacities
Mower Model No
Machine Weight
Width of Cut
Cutting Height
Trim Capacity (left side)
Overall width
Chute down
Overall tire-to-tire width
Overall Length
Overall Height
Drive Tires
Front Tires
Hour Meter
Fuel Capacities
Steering Type
Twin Lever Steering Controls
Steering Turning Radius
Brake Service
Park Brake Type
Ground Speed
Motor Drive
Wheel Drive
Electrical Operated Logic-Control
Safety Features
Evaporative Emission Control
System on EPA Compliant Mowers
Seat
Mainframe Construction
Front Caster Wheels
Front Caster Fork Construction
Deck Thickness
Reinforced Front Edge
Deck Trim Edges
Deck Housing Depth
Deck Lift
Hand Operated Controls
Indicators
Cup Holder
Cutting Height Adjustments
Mowing Blades
Blade Tip Speed
Blade Drive
Blade Spindles
Deck Suspension
Number of Anti-Scalp Rollers
46
ZST40 & ZST48 Zero Turn Mowers 357-505M
Table of Contents
General Specifications & Capacities
Hydrostatic Twin lever steering provides independent control of each drive wheel.
True zero degree. Turns with counter-rotating independent drive wheels.
Manual activated over-center lever to pawl over cog wheel.
Single V-belt with spring take-up idler pulley and electric clutch at engine crankshaft.
Electric logic-control system governs blade engagement, forward & reverse motion,
This equipment uses a sealed fuel system which incorporates a non-vented fuel cap.
Evaporative emissions are vented to the engine where they are combusted during
11 Gauge decks with 11 gauge doubler plate at blade spindle housing mounts
40" Deck
Solid 1" x 3/8" steel bar is incorporated into the deck front to reinforce its front edge.
48" Deck
Deck front is bent 90
Foot-operated deck height adjustment with deck stop pin for setting height.
(2 ea.) .25" x 2 1/2" x 20.9"
Single B-Section belt drive to all blade spindles with spring loaded take-up idler pulley.
Machined ductile iron housing, 1 3/8" diameter high carbon steel shafts
Four point suspension from frame by mechanical linkage.
ZST40
581 lbs
40"
1" to 4 1/2" In 1/2" increments
1 1/2"
52 1/2"
38"
74 1/4"
41"
4-bolt, 18 x 7.5 - 8 Turf Tread
11 x 4 - 5, Ribbed tread with roller bearings
Standard equipment
3 US GAL
Speed, forward, reverse, brake, and turns.
Hydrostatic dynamic braking.
Forward: 0-6 MPH & Reverse: 0-4 MPH
Dual integrated hydrostatic transaxle.
engine starting & running, and parking brake functions.
normal engine operation.
Standard black seat
Welded steel square tubing
Free turning with sealed for life ball bearings.
3/8" steel.
o
at the bottom to reinforce its front edge.
Solid 1" x 3/8" steel bar for reinforced trim edge.
4 3/8" deep, (room for high-capacity mowing)
Ignition switch, throttle lever, control levers,
park brake, blade engagement switch, and choke knob.
Engine warning light and hour meter for engine run time.
One cup holder molded into the left side fender.
Height adjustment in 1/2" increments from 1" to 4 1/2".
Heavy-duty, heat-treated, medium-lift steel blades
18,300 FPM
and greasable ball bearings.
1
ZST48
596 lbs.
48"
5 1/2"
65 1/2"
(3 ea.) .25" x 2 1/2" x 16 7/8"
18,700 FPM
2
12/15/15
Advertisement
Table of Contents
