Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DCD925
Summary of Contents for DeWalt DCD925
- Page 1 DCD920 DCD925 DCD930 DCD935 DCD940 DCD945 www. .com...
- Page 2 English (original) 한국 어 Copyright D WALT...
- Page 3 Figure 1 DCD920 DCD925...
- Page 4 Figure 2 Figure 3 Figure 5 Figure 4 Figure 6...
- Page 5 Figure 7 Figure 9 Figure 8 Figure 10 Figure 12 Figure 11 Figure 13...
-
Page 6: Technical Data
ENGLISH 1/2" (13 mm) CORDLESS DRILL/DRIVER DCD920, DCD930, DCD940 1/2" (13 mm) CORDLESS HAMMERDRILL/DRIVER DCD925, DCD935, DCD945 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make WALT one of the most reliable partners for professional power tool users. - Page 7 E NGLI SH Vibration emission value a Screwdriving m/s² < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 m/s² Uncertainty K = An estimation of the level of exposure to The vibration emission level given in this information vibration should also take into account sheet has been measured in accordance with a the times when the tool is switched off...
-
Page 8: General Power Tool Safety Warnings
EN GL ISH WARNING: To reduce the risk of injury, If operating a power tool in a damp read the instruction manual. location is unavoidable, use a residual current device (RCD) protected supply. General Power Tool Safety Warnings Use of an RCD reduces the risk of electric shock. - Page 9 E NGLI S H Do not use the power tool if the switch Under abusive conditions, liquid may be does not turn it on and off. Any power ejected from the battery, avoid contact. tool that cannot be controlled with the switch If contact accidentally occurs, flush with is dangerous and must be repaired.
- Page 10 EN GL ISH – Health hazards caused by breathing dust charger from the power supply when developed when working in wood. there is no battery pack in the cavity. Unplug charger before attempting to – Risk of personal injury due to flying particles. clean.
- Page 11 ENGLISH SAVE THESE INSTRUCTIONS Hot/Cold Pack Delay When the charger detects a battery that is too hot Chargers or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery has The DE9116 charger accepts 7.2–18 V NiCd and reached an appropriate temperature.
- Page 12 However, if the outer seal is broken: BATTERY TYPE and the battery liquid gets on your skin, immediately wash with soap and water for The DCD925 and DCD920 operate on 18 volt several minutes. battery packs. and the battery liquid gets into your eyes,...
-
Page 13: Package Contents
DO NOT use under wet conditions or in presence of The package contains: flammable liquids or gases. 1 cordless percussion drill These drills/drivers/hammerdrills are professional (DCD945, DCD935, DCD925 models) power tools. 1 cordless midhandle drill driver DO NOT let children come into contact with the (DCD940, DCD930, DCD920 models) tool. -
Page 14: Assembly And Adjustments
ENGLISH Side Handle (fi g. 1) Your D WALT charger is double insulated in accordance with EN 60335; therefore WARNING: To reduce the risk of no earth wire is required. personal injury, ALWAYS operate If the supply cord is damaged, it must be replaced the tool with the side handle properly by a specially prepared cord available through the installed. - Page 15 The three-speed feature of your tool allows you to SELF-TIGHTENING CHUCK OPERATION (FIG. 10–12) shift gears for greater versatility. To select speed 1 DCD945, DCD935, DCD925 (highest torque setting), turn the tool off and permit it To insert a drill bit or other accessory: to stop.
-
Page 16: Drill Operation
ENGLISH the sleeve clockwise (viewed from the front) with 5. IF DRILL STALLS, it is usually because it one hand while using the other hand to secure is being overloaded. RELEASE TRIGGER the tool. Rotate the sleeve clockwise until sleeve IMMEDIATELY, remove drill bit from work, cannot be rotated any further, as demonstrated and determine cause of stalling. -
Page 17: Optional Accessories
ENGLISH 5. For masonry, use carbide-tipped bits or Optional Accessories masonry bits. A smooth, even flow of dust WARNING: Since accessories, other indicates the proper drilling rate. than those offered by D WALT, have not been tested with this product, use MAINTENANCE of such accessories with this tool could Your D... - Page 18 ENGLISH Rechargeable Battery Pack This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment: Run the battery pack down completely, then remove it from the tool.
- Page 19 1/2" (13 DCD920, DCD930, DCD940 1/2" (13 DCD925, DCD935, DCD945 DCD920 DCD935 DCD930 DCD945 DCD940 14.4 14.4 0-500 0-425 0-425 0-425 0-425 0-1,250 0-1,200 0-1,200 0-1,200 0-1,200 0-2,000 0-1,800 0-1,800 0-1,800 0-1,800 0-7,225 0-7,225 0-20,400 0-20,400 0-30,600 0-30,600 1.5-13 1.5-13 1.5-13...
- Page 20 m/s² < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 < 2.5 m/s² EN 60745 DE9180 DE9503 DE9140 DE9502 DE9501 14.4 14.4 0.68 0.58 0.86 0.69 DE9135 DE9116 (2.0 (2.0 0.52...
- Page 22 – – –...
- Page 23 – – –...
- Page 24 – – – – – – ––––––––––– –– – –– –...
- Page 25 –...
- Page 27 –...
- Page 28 – – – –...
- Page 29 –...