Specifications - Makita 6260D Instruction Manual

ENGLISH
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Low speed

SPECIFICATIONS

Model
Capacities
Steel .............................................. 10 mm
Wood ............................................. 21 mm
Wood screw ................................... 5.1 mm x 38 mm
Machine screw............................... 6 mm
-1
No load speed (min )
High ...............................................0 – 1,200
Low ................................................ 0 – 350
Overall length ................................... 192 mm
Net weight......................................... 1.4 kg
Rated voltage ................................... D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Explanation of general view
6 High speed
7 Speed change lever
8 Graduations
9 Adjusting ring
10 Drill marking
6260D 6270D
10 mm
25 mm
5.1 mm x 63 mm
6 mm
0 – 1,200
0 – 350
192 mm
1.5 kg
D.C. 12 V
ENC004-1
11 Pointer
12 Sleeve
13 Ring
14 Tighten
6280D
10 mm
25 mm
5.1 mm x 63 mm
6 mm
0 – 1,200
0 – 350
192 mm
1.6 kg
D.C. 14.4 V
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
ADDITIONAL SAFETY RULES FOR POWER
TOOL
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
6390D
13 mm
36 mm
6 mm x 75 mm
6 mm
0 – 1,200
0 – 350
220 mm
2.2 kg
D.C. 18 V
GEB002-2
3