Yaesu FT1DR Technical Supplement page 10

Rotate the DIAL knob to select the Alignment
Menu "HI POWER".
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit and rotate the
DIAL knob so that the Power Meter reading is
4.9 W (±0.05 W).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
TX Power (L3) Adjustment (L3 POWER)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "L3 POWER".
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit and rotate the
DIAL knob so that the Power Meter setting is
2.5 W (±0.1 W).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
TX Power (L2) Adjustment (L2 POWER)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "L2 POWER".
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit and rotate the
DIAL knob so that the Power Meter setting is
0.9 W (±0.1 W).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
TX Power (L1) Adjustment (L1 POWER)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "L1 POWER".
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit and rotate the
DIAL knob so that the Power Meter setting is
0.1 W (±0.02 W).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
Digital TX Deviation Adjustment (DIG DEV)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "DIG DEV".
Press the [ V/M ] button (the "E" icon will appear
on the display).
P r e s s t h e [ B A N D ] b u t t o n t o s e l e c t t h e
"DIG DEV". (Don't touch alignment menu
"VCO MOD")
Press the PTT switch to transmit and rotate the
DIAL knob so that the Deviation Meter setting is
4.5 kHz ± 0.1 kHz (Both USA and EXP version).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
TX Deviation Adjustment (MAX DEV)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "MAX DEV".
Set the AF Signal Generator output to 50 mVrms
with a 1 kHz audio tone.
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit and rotate the
DIAL knob so that the Deviation Meter setting is
4.35 kHz ± 0.05 kHz (USA version) or 4.65 kHz
± 0.05 kHz (EXP version).
Release the PTT switch, and then press the
[ V/M ] button (the "E" icon will disappear on the
display).
CTCSS TX Deviation Adjustment (100.0 Hz)
Connect the test equipment as shown in Figure 1:
TX Alignment Setup.
Rotate the DIAL knob to select the Alignment
Menu "100.0 Hz".
Press the [ V/M ] button (the "E" icon will appear
on the display).
Press the PTT switch to transmit without the
microphone input and rotate the DIAL knob
so that the Deviation Meter setting is 0.65 kHz
(±0.05 kHz).
ALIGNMENT-4
Alignment
FT1DR/DE Technical Supplement