Explanation Of General View; Specifications - Makita LS1016 Instruction Manual

ENGLISH (Original instructions)
1. Stopper pin
2. Hex bolts
3. Blade guard
4. Kerf board
5. Saw blade
6. Blade teeth
7. Left bevel cut
8. Straight cut
9. Right bevel cut
10. Lock lever
11. Locking screw
12. Adjusting bolt
13. Turn base
14. Stopper lever
15. Slide pipe
16. Top surface of turn base
17. Periphery of blade
18. Guide fence
19. Stopper arm
20. Adjusting screw
21. Grip
22. Cam
23. Lever
24. Latch lever
25. Scale plate
26. Release button
27. Pointer
28. Lock-off button
29. Switch trigger
30. Hole for padlock
31. Switch for laser
32. Wrench holder
33. Hex wrench

SPECIFICATIONS

Model
Blade diameter
For all countries other than European countries
For European countries
Hole diameter
For all countries other than European countries
For European countries
Max. Cutting capacities (H x W) with 260 mm in diameter
45° (right and left)
52° (right and left)

Explanation of general view

34. Center cover
35. Hex socket bolt
36. Shaft lock
37. Blade case
38. Arrow
39. Outer flange
40. Inner flange
41. Spindle
42. Ring
43. Socket wrench
44. Hex bolt
45. Fastener
46. Dust bag
47. Dust nozzle
48. Dust box
49. Cover
50. Button
51. Cylinder section
52. Sawdust
53. Support
54. Levers
55. Clamping screws
56. Upper fence
57. Lower fence
58. Red indicating area
59. Vise knob
60. Vise arm
61. Vise rod
62. Screw
63. Vise plate
64. Vise nut
65. Holder
66. 52/38° type crown molding
Miter angle
0°
60° (right)
67. 45° type crown molding
68. 45° type cove molding
69. Inside corner
70. Outside corner
71. Crown molding stopper L
(Optional accessory)
72. Crown molding stopper R
(Optional accessory)
73. Crown molding stopper L
74. Crown molding stopper R
75. Crown molding
76. Vise
77. Spacer block
78. Aluminum extrusion
79. Cut grooves with blade
80. Triangular rule
81. Miter scale
82. Bevel scale plate
83. 0° Angle adjusting bolt
84. Top surface of turn table
85. Left 45° bevel angle adjusting bolt
86. Right 45° bevel angle adjusting
bolt
87. Workpiece
88. Laser line
89. Vertical vise
90. Screw to change the movable
range of the adjusting screw
91. Screwdriver
92. Screw (one piece only)
93. Lens for the laser light
94. Limit mark
95. Brush holder cap
Bevel angle
45° (left)
42 mm x 310 mm 68 mm x 310 mm
58 mm x 279 mm 91 mm x 279 mm
42 mm x 218 mm 68 mm x 218 mm
58 mm x 197 mm 91 mm x 197 mm
68 mm x 190 mm
-
91 mm x 171 mm
68 mm x 155 mm
-
91 mm x 139 mm
LS1016/LS1016L
255 mm - 260 mm
260 mm
25.4 mm
0° 45° (right)
29 mm x 310 mm
43 mm x 279 mm
29 mm x 218 mm
43 mm x 197 mm
-
-
30 mm
13