Explanation Of General View; Specifications - Makita LS1216F Instruction Manual

ENGLISH
(Original instructions)
1 Stopper pin
2 Hex bolt(s)
3 Blade guard
4 Kerf board
5 Saw blade
6 Blade teeth
7 Left bevel cut
8 Straight cut
9 Right bevel cut
10 Lock lever
11 Locking screw
12 Adjusting bolt
13 Turn base
14 Stopper lever
15 Slide pipe
16 Top surface of turn base
17 Periphery of blade
18 Guide fence
19 Stopper arm
20 Adjusting screw
21 Grip
22 Cam
23 Levers
24 Latch lever
25 Scale plate
26 Release button
27 Pointer
28 Lock-off button
29 Switch trigger
30 Hole for padlock
31 Switch for light
32 Light
33 Switch for laser
34 Wrench holder
35 Hex wrench
36 Socket wrench

SPECIFICATIONS

Model
Blade diameter .................................................................................................................................................... 305 mm
Blade body thickness ........................................................................................................................... 1.6 mm – 2.4 mm
Hole diameter.....................................................European countries: 30 mm, other than European countries: 25.4 mm
Max. Miter angle.................................................................................................................................. Left 52°, Right 60°
Max. Bevel angle..................................................................................................................................Left and Right 45°
Max. cutting capacities (H x W)
Miter angle
0°
Thickness of wood
facing on guide
fence for increased
height of cut
45° (left and right)
Thickness of wood
facing on guide
fence for increased
height of cut
16

Explanation of general view

37 Center cover
38 Hex socket bolt
39 Shaft lock
40 Blade case
41 Arrow
42 Outer flange
43 Inner flange
44 Spindle
45 Ring
46 Fastener
47 Dust bag
48 Dust nozzle
49 Dust box
50 Cover
51 Button
52 Cylinder section
53 Sawdust
54 Support
55 Turn base
56 Clamping screws
57 Upper fence
58 Lower fence
59 Red indicating area
60 Vise knob
61 Vise arm
62 Vise rod
63 Screw
64 Vise plate
65 Vise nut
66 Holder
67 52/38° type crown molding
68 45° type crown molding
69 45° type cove molding
70 Inside corner
71 Outside corner
45° (left)
59 mm × 382 mm
69 mm × 363 mm
35 mm 78 mm × 290 mm
60 mm –
59 mm × 268 mm
69 mm × 255 mm
30 mm –
45 mm –
72 Crown molding stopper L
(Optional accessory)
73 Crown molding stopper R
(Optional accessory)
74 Crown molding stopper L
75 Crown molding stopper R
76 Crown molding
77 Vise
78 Spacer block
79 Aluminum extrusion
80 Over 15 mm
81 Over 290 mm
82 Over 340 mm
83 Hole
84 Cut grooves with blade
85 Screws (two each side)
86 Lower fence
87 Base
88 Platform
89 Vertical vise
90 Workpiece
91 Triangular rule
92 Miter scale
93 Bevel scale plate
94 0° Angle adjusting bolt
95 Top surface of turn table
96 Left 45° bevel angle adjusting
bolt
97 Right 45° bevel angle adjusting
bolt
98 Laser line
99 Screwdriver
100 Screw (one piece only)
101 Lens for the laser light
102 Limit mark
103 Brush holder cap
LS1216/LS1216L/LS1216F/LS1216FL
Bevel angle
0°
87 mm × 382 mm 44 mm × 382 mm
102 mm × 363 mm 54 mm × 363 mm
115 mm × 300 mm 61 mm × 290 mm
120 mm × 250 mm
87 mm × 268 mm 44 mm × 268 mm
102 mm × 255 mm 54 mm × 255 mm
115 mm × 202 mm
120 mm × 172 mm
45° (right)
–
–
–