Control 4 C4-16S2-E-B Installation And Setup Manual page 3

Use the Select dial to scroll the number up or down and edit as needed, and then press
the Select dial to move to the next field within the number.
6 When you're finished editing, press Save.
Use Audio Matrix Switch
This section introduces the user interface available to Audio Matrix Switch users and com-
mon system tasks you can perform with the Audio Matrix Switch from the front display.
Note: Following initial setup, you may never need to change settings on the Audio Matrix
Switch manually. This device is managed by the Control4 system. The use of this section is
completely optional.
This device assists in fulfilling a room-specific music request. To play music, use a Navigator
available for the room to choose a specific music source or a device. That device may or
may not need to make use of this switch.
View Output Assignments
When you complete the physical and logical setup tasks, you can view or change setup
configuration in the Audio Matrix Switch front display.
When you power up the Audio Matrix Switch, the following System Status screen appears
momentarily.
The System Status screen is then replaced by the In to Out Assignments screen.
When you make an assignment, the screen displays the assignment. For example, Output 1
is mapped to Input 1.
Manage Outputs
View Output Assignments
To view output assignments:
1 Ensure your Audio Matrix Switch is powered up and that the In to Out Assignments
screen displays in the front display.
2
On the In to Out Assignments screen, view the current input-to-output assignments.
The screen consists of 16 output zones and any assigned input source. The shaded arrow
indicates the Output currently selected.
To explore these menu options, press the buttons on the front panel:
• Setup: Displays an output-specific screen. The most recent screen accessed is dis-
played by default, but you can choose to view a different output's setting by changing
the Output number.
• Network: Displays the Network Configuration screen. From this screen, you can
select Ethernet or Zigbee.
• Display: Displays the Display Configuration Screen.
Configure an Output
To change output source or settings:
1 On the Output to Input screen, press the Setup button to view the output settings of the
default output screen (which is the last output screen accessed).
From the output screen, you can: (1) change to another output screen; (2) change the
output settings on the screen; or (3) toggle to the Input Signal Sensing screen.
2 If the output-specific screen you want to view did not display, use the Select Dial to
highlight and select the output number and then change it.
3 (Optional) Change settings for the current output using the supported ranges:
• Input: Displays the number of the currently assigned input source and any label
given to the input source. You can change this setting to any available input
sources.
• Gain: Supported range: Mute and -44 to +4 dB (default: 0 dB)
• Treble: Supported range: -12 to +12 dB (default: 0 dB)
• Bass: Supported range: -12 to +12 dB (default: 0 dB)
• Balance: Supported range: -50 to +50dB (default: 0 dB)
4 To toggle to view input signal sensing information, press the Inputs button.
5 To exit the screen, press the Exit button.
6 Rotate the Select Dial to highlight a setting.
7
Press the Select Dial to enter edit mode.
8 Rotate the dial to change the setting; then press the dial to Save the new setting and
exit edit mode or, to exit without saving, use the Cancel button.
9
Press the Inputs button to go to the Input Signal Sensing screen, or press the Exit but-
ton to return to the Output to Input screen.
Check Signal Status
1 From the Output to Input screen, press the Setup button, and then press the Inputs
button to access the Input Signal Sensing screen.
2 On the Input Signal Sensing screen, a shaded circle appears by the device connection
number of any input device with a signal present.
View Network Settings
To view network settings:
1 Press Network.
2
From the Network Configuration screen, select Ethernet or Zigbee.
3 To return to the Network Configuration screen, press Back.
Set Front Display Preferences
To set your viewing preferences for the front display:
1 On the Output to Input screen, press the Display button. The Display Configuration
screen appears.
Use the buttons and/or the Select dial to choose a setting to change: When you press
the Select button (or press the dial), you enter edit mode.
In edit mode, use the buttons or Select dial to change the highlighted setting then press
the OK button (or press the dial) to save the change and exit.
• Brightness: Supported range: 0 to 100
• Contrast: Supported range: 0 to 100
• Backlight Timeout: Supported settings are:
• OFF (always off)
• 1 to 90 seconds (default is 30 seconds)
• ON (always on)
• Reset Defaults: Restores factory defaults.