Failure-Test Method For The Hdmi Transmitter Ic - Pioneer DV-989AVi-S Service Manual

5

7.1.8 FAILURE-TEST METHOD FOR THE HDMI TRANSMITTER IC

QQ
3 7 63 1515 0
• When replacing the DVDM Assy, see "7.1.10 DISASSEMBLY"
In a case where the HDMI video signal is not output
1
Is the Pure Audio function turned ON?
(During Pure Audio mode, neither the HDMI signal nor the analog
video signal is output.)
Is the analog video signal output?
Check if the HOME MENU or VCD playback picture is displayed
when this unit is connected to a PC monitor equipped with a
DVI input.
Purpose: To check if the HDMI output line, including the
terminal, is in failure.
(An HDMI↔DVI conversion cable is required for checking.)
Failure test for the T-REX (IC1001: DVDM Assy)
Probe R1013-R1018 (22 ohms × 4, 6 sets), and R1009 (27-MHz
clock) with an oscilloscope, and check if the amplitude of each
TE
L 13942296513
signal changes between H (3.3 V) and L during VCD playback
and if the 27-MHz clock is output correctly.
The T-REX or the line between the T-REX and the HDMI
transmitter IC may be in failure (replacement of the T-REX,
failure in any of the above resistors, defective soldering, signal
short-circuiting, or broken wires, etc.)
In a case where the HDMI audio signal is not output
2
Is the Pure Audio function turned ON?
(During Pure Audio mode, the HDMI audio signal is not output.)
Is this unit connected to DVI equipment?
(Only a video signal is available with DVI equipment.)
Are the audio signals properly output from the optical outputs
and coaxial outputs (S/PDIF)?
www
Probe R1058 (S/PDIF) and R1057 (22-/24-MHz clock) with an
oscilloscope, and check if correct signals are output. The HDMI
transmitter IC (audio processing block) may be in failure.
.
The lines from R1058 (S/PDIF) and R1057 (22-/24-MHz clock)
are in failure.
(The optical-output and coaxial-output lines are OK.)
5
http://www.xiaoyu163.com
6
No
Yes
No
NG
No
No
Yes
x ao u163
y
No
i
6
http://www.xiaoyu163.com
7
2 9
8
Yes
Turn the Pure Audio function OFF.
No
IC901 (DVDM Assy) and its peripheral circuits may be in failure.
Check if the initialization process for HDCP, etc. is OK by
Yes
connecting this unit with a Pioneer Plasma Display equipped
with an HDMI input.
NG
The customer's monitor may not be compatible
with this unit. Confirm the name of manufacturer
and model of the monitor, and get a specific
description of the failure. Then look for an identical
case in a collection of past cases, or consult the
design section. In some cases, upgrading the
software or firmware for both the DVD player and
the monitor will solve the problem.
The HDMI transmitter IC
(HDCP process block) may
be in failure.
The HDMI transmitter IC or
Q Q
OK
3 6 7 1 3 1 5
the line between the IC and
the output terminal may be
in failure.
Yes
Turn the Pure Audio function OFF.
Yes
Replace the DVDM Assy.
co
.
DV-989AVi-S
7
9 4 2 8
OK
Replace the DVDM Assy.
0 5 8 2 9 9 4 2 8
Replace the DVDM Assy.
m
8
9 9
A
B
C
9 9
D
E
F
103
8