LD ON mode in the test mode oscillates with the laser forcibly. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 49. DV-585A-S...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-585A-S...
(In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION For WYXTL type and WYXTL/UR type For WVXTL type 7 or 11 8-10 "Operating Instructions" For WVXTL type and WYXTL/UR type For WYXTL type For WVXTL type Only DV-585A-S...
Page 7
See Contrast table (2) Operating Instructions See Contrast table (2) Operating Instructions See Contrast table (2) (2) CONTRAST TABLE DV-585A-S/WYXTL, /WVXTL, /WYXTL/UR and DV-585A-K/WYXTL are constructed the same except for the follow- ing : DV-585A-S/WYXTL/ Mark Symbol and Description DV-585A-S/WYXTL DV-585A-S/WVXTL DV-585A-K/WYXTL >...
Page 9
Screw,Tap Tite(B) (3x6.0) See Contrast table (2) Screw,Tap Tite(B)Pan (3x6) 810913060U Screw,Tap Tite(P)Bind (2.6x8) 811022680U (2) CONTRAST TABLE DV-585A-S/WYXTL, /WVXTL, /WYXTL/UR and DV-585A-K/WYXTL are constructed the same except for the follow- ing : DV-585A-S/WYXTL/ Mark Symbol and Description DV-585A-S/WYXTL DV-585A-S/WVXTL DV-585A-K/WYXTL...
CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. PART NAME MARK grease are displayed for this section. GREASE G-478B GEM1018 Check if the correct grease is applied for each GYA1001 PN-397 position. GEM1036 ME-913A DV-585A-S...
Page 15
S VIDEO OUT J8001 AUDIO OUT CP502(14P) CD8001(12P FFC) Cord Connector 122HC0C3001 06C32E3504 J8101 SCART 1/2- J8102 COAXIAL DIGITAL POWER PCB ASSY (A2G604A240) AUDIO OS8101 : POWER BLOCK OPTICAL J501 : DIGITAL AUDIO BLOCK BLUE LIVE AC IN NEUTRAL BROWN DV-585A-S...
3.3 DVD MT PCB (1/6) ASSY DVD MT PCB ASSY (A2G604A130) MPEG/MICON/RF-AMP BLOCK (RF) (RF) (RF) MPEG/MICON EEPROM DV-585A-S...
Page 17
: S VIDEO SIGNAL ROUTE (C ch) (R/CR) : VIDEO SIGNAL ROUTE (R/CR ch) (G/Y) : VIDEO SIGNAL ROUTE (G/Y ch) (B/CB) : VIDEO SIGNAL ROUTE (B/CB ch) : AUDIO DATA SIGNAL ROUTE (DA) : AUDIO SIGNAL ROUTE (Digital) RESET IC CP601 DV-585A-S...
DVD MT PCB ASSY (A2G604A130) MEMORY BLOCK NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST DURING PLAYBACK. AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-585A-S...
LOADER/MOTOR DRV BLOCK (RF) (RF) NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-585A-S...
3.6 DVD MT PCB (4/6) ASSY DVD MT PCB ASSY (A2G604A130) AUDIO JACK BLOCK CP8001 (DA) : AUDIO DATA SIGNAL ROUTE (DA) : AUDIO SIGNAL ROUTE (Digital) : AUDIO SIGNAL ROUTE (L ch) (DA) DV-585A-S...
Page 23
NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. AUDIO LPF& AUDIO LPF& AUDIO LPF& DV-585A-S...
V out C7312 GND1 GND2 VSEL1 BIAS Y out C7313 (SY) I/XP G/Y_OUT CY out C7307 CY in GND2 B/U_OUT Cb out (CB) (CB) C7308 B/CB Cb in GND2 R/V_OUT MUTE2 Cr out (CR) (CR) C7309 R/CR Cr in GND2 DV-585A-S...
Page 25
Y/C SEPA J7301 (CB) MDC-070V-B_LF R/V_IN (CR) CVBS/Y/U/V J7302 4PIN only ---> W821,W822,W826 ON 4PIN+21PIN ---> IC7302 MOUNT,JP DEL MSP-244V10-95_NI_FE_LF 4PIN+D ---> W821,W822,W826,W853,W856,W864 ON NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-585A-S...
Page 26
3.8 DVD MT PCB (6/6) ASSY DVD MT PCB ASSY (A2G604A130) POWER PORT BLOCK REG+1.8V IC DV-585A-S...
Page 27
NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-585A-S...
10ERB20-TA1B2 22 1 / 4W R507 IC504 PS2561AL1-1-V(W) 10 1 / 4W 16.4 R515 C518 0.001 KX • NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS OF FUSE. DV-585A-S...
Page 31
DAC_B[R]V_VIDEO 0.01 R / C R P-H/I-L_RGB-H R513 C503 RGB-H ASP/FS 1/4W 0.1 B CP7301 21PIN_CVBS_VIDEO CVBS CAUTION:DIGITALTRANSISTOR IC501KIA431A-AT GN D AMP_A_OUT_L AUDIO L VOLTAGE AMP_A_OUT_R AUDIO R VIDEO/AUDIO for 21PIN Q506 CAUTION:DIGITALTRANSISTOR KTA1504S_Y_RTK R527 Q501 100 1/4W KTC3875S_Y_RTK DV-585A-S...
P.C.Board Resistor array 3-terminal regulator LOADING MOTOR LOADING MOTOR PCB ASSY PCB ASSY (INSERTED PARTS) (CHIP MOUNTED PARTS) SIDE A SIDE B CD2302 CP2302 SW PCB ASSY M2603 LOADING MOTOR CD2301 M2602 SLED MOTOR CD2301 M2601 SPINDLE CP2303 MOTOR DV-585A-S...
Page 47
06C32E3504 CP503 CONNECTOR 069J7C0599 J8101 SOCKET, 21 PIN 063D100050 J8102 RCA JACK 060Q401115 OS8101 OPTICAL DRIVICE 07AQ000009 CP8102 CONNECTOR PCB SIDE 06C3223003 SW PCB ASSY There is no Service Parts LOADING MOTOR PCB ASSY There is no Service Parts DV-585A-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Pick Up PCB Short circuit using a soldering iron. Fig. 1 DV-585A-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-585A-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-585A-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-585A-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-585A-S...
After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-585A-S...
1 Destination indication Display it according to model information set from the FL Driver IC. 2 Region No. 3 ROM number Rom display Version. 5 SUM CHK SUM value of E2P ROM displays with four places. 6 CHIP VERSION DV-585A-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-585A-S...
Measure the voltage between the two ends of R2320 or R2322 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. To OPTICAL PICKU DVD MT PCB ASSY CP2301 Front side SIDE A DV-585A-S...
DVD MT PCB Assy Check the video signal path between DVD IC (DVD MT Assy IC4002) displayed on the monitor Video circuit after DVD IC and video-out terminal (see the block diagram) (The FL display lights. The (IC4002) mechanism does not work.) DV-585A-S...
Page 58
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT Assy : IC4002) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT Assy : IC4005) Block noise is generated during playback. DV-585A-S...
Up PCB and DVD PCB connector. 1-4: DVD PCB (Refer to Fig. 1-4) Power PCB Remove the 4 screws 1. Remove the 4 screws 2. Remove the DVD PCB in the direction of arrow. DVD PCB Fig. 1-2 Fig. 1-4 DV-585A-S...
Page 61
3 supports 1. between A and B. Fig. 2-3-D Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Clamper Check Hook Fig. 2-5-A Fig. 2-3-E DV-585A-S...
Page 62
Remove the Switch PCB Ass'y. 8.0 ± 0.2mm Remove the screw 4. Remove the Gear Feed. Feed Motor Remove the 2 screws 5. Remove the Feed Motor. Remove the Gear Motor. Safety surface for pressing of the insert. Fig. 2-7-C DV-585A-S...
Page 63
When installing the FFC, fold it correctly and install it as shown from Fig. 2-8. NOTE Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Printing _Serface 85±1 mm Reinforcement Plat To Pick Up PCB Fig. 2-8 DV-585A-S...
Page 65
TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System Audio Parser Audio Output CPPM/CPRM SPDIF System GPIO 32-bit RISC IR/VFD DV-585A-S...
Page 66
While External FLASH size <= 2MB: 45 NC – – Version AD input port 0, or DVDD3 – 3.3V power pin for internal digital circuitry GPIO FG(Diogital pin) – Motor Hall sensor input, or Version AD input 8 90 ALE Microcontroller address latch enable DV-585A-S...
Page 67
133 RD9 DRAM data 9 185 NC – – 134 DVSS – 3.3V Ground pin for internal digital circuitry 186 NC – – 135 RD8 DRAM data 8 187 NC – – 136 DQS1 GPIO 188 NC – – DV-585A-S...
Page 68
236 LPFIP The positive input terminal of loop filter amplifier GPIO 237 LPFIN The negative input terminal of loop filter amplifier 212 DVDD3 – 3.3V power pin for internal digital circuitry 238 LPFOP The positive output of loop filter amplifier DV-585A-S...
Page 69
RF path. Connect 246 RFRPAC RF ripple detect input (through AC-coupling) an external 15K resistor to this pin and 247 HRFZC High frequency RF ripple zero crossing AVSS 248 CRTPLP Defect level filter capacitor connecting 256 AVDD3 – Analog power 3.3V DV-585A-S...
Page 73
Logic Power Supply 13,43 High-Voltage Segment Output Pins 14 to SG1/KS1 to SG16/KS16 Also acts as the Key Source – Pull-Down Level 31 to SG17/GR12 to SG24/GR5 High Voltage Segment/Grid Output Pins 39 to GR4 to GR1 High-Voltage Grid Output Pins DV-585A-S...
Page 74
Super VCD also supports the widescreen size. Player for Windows XP, or Windows MediaPlayer 9 Series. Microsoft, Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. Super VCD DV-585A-S...
Page 75
Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information. • The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10. DV-585A-S...
8. PANEL FACILITIES 8.1 FRONT PANEL SECTION Front panel STANDBY/ON AU D IO/VIDEO STANDBY/ON Disc tray OPEN/CLOSE Remote control sensor Display RW Compatible DV-585A-S...
Indicates that the character display is showing a DVD title number. Lights during multi-angle scenes on a DVD disc. PRGSVE Lights when the player is set to output progressive scan video. Lights in any of the repeat play modes. DV-585A-S...
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-585A-S...
Page 79
Use to select menu options, etc. playing. 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-585A-S...
Page 80
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Refer to "2.3 05 DVD MECHA SECTION" , "7.2 DISASSEMBLY SECTION". Cleaning paper : GED-008 DV-585A-S...