Page 1
Home Network System Window/Door Sensor KX-HNS101AZ Model No. Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 17).
Table of Contents Introduction Accessory information ....3 Important Information About this system ......4 For your safety ......4 Important safety instructions ..5 For best performance ....5 Other information .......6 Setup Part names and functions ..7 LED indicator ......7 Setup overview ......7 Inserting the battery ....8 Registering the window/door sensor ........8...
Introduction Accessory information Supplied accessories Accessory item/Part number Quantity Battery Mounting screws (20 mm) Mounting double-sided tapes When replacing the battery, see “Power source” of “Specifications”, page 17 for battery information. 2 screws for the sensor unit and 2 screws for the magnet unit 2 pieces of tape for the sensor unit 1 piece of tape for the magnet unit Other information...
R Keep small parts (magnet unit, protection from property loss. magnet unit cover, screws, etc.) out Panasonic will not be held of the reach of children. There is a responsible in the event that risk of swallowing. In the event they...
Hub location/avoiding noise swallowing. If the battery is The hub and other compatible swallowed, seek medical attention Panasonic devices use radio waves to immediately. communicate with each other. R Remove the battery if it becomes unusable. There is a risk of leakage, HNS101AZ_(en_en)_0325_ver.031.pdf...
Important Information R For maximum coverage and noise-free communications, place Other information your hub: – at a convenient, high, and central CAUTION: Risk of explosion if battery location with no obstructions is replaced by an incorrect type. between the product and hub in Dispose of used batteries according to an indoor environment.
Setup Indicator Status Part names and Red, Sensor is out of range blinking of the hub functions Green, Registration mode n Sensor unit blinking (You pressed and held No battery power Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 8).
Setup operation was confirmed (page 13). Registering the window/door sensor Inserting the battery This procedure is not required for devices that were included as part of R USE ONLY a CR2 Lithium battery. a bundle. R Confirm the polarities ( Before you can use the window/door Remove the sensor unit cover.
Setup devices and group them by location. For more information, refer to the Wireless User’s Guide (page 17). communication range Changing the sensor The wireless communication range of type each device in the system from the hub is approximately 50 m indoors and You can select whether a window/door approximately 300 m outdoors.
Setup Temporary placement Before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing M Important: R Attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door.
Page 11
Setup Example 1: Installed on the left side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Page 12
Setup Example 2: Installed on the right side of a window Correct Green “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect “...
Setup Installation Install the window/door sensor in the same position where proper operation was confirmed (page 10). You can install the window/door sensor using screws or double-sided tape, depending on your preference or the material of the installation area. Note: R When installing, make sure the battery is inserted properly and the sensor unit cover is completely closed.
Page 14
Setup Sensor unit: Attach the sensor unit. Screws 86.2 mm Magnet unit: Attach the magnet unit. Screws 24.4 mm Attach the covers. Important: Align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm apart. HNS101AZ_(en_en)_0325_ver.031.pdf 2015/03/25 14:20:39...
Page 15
Setup Securing with double-sided tape Note: R Make sure the surfaces of the sensor unit, magnet unit, and the installation area are clean and dry before applying double-sided tape. Check that the sensor unit cover and magnet unit cover are attached. Affix double-sided tape to the sensor unit and magnet unit.
Appendix You can configure the window/door sensor to trigger other system Testing the window/ events, such as camera recording, door sensor turning on an electric device (such as a lamp), etc. (Appropriate device You can check the window/door required.) sensor’s LED indicator and test the –...
Sensor unit: Approx. 102 mm ´ 31 mm ´ 22 mm Magnet unit: Approx. 37 mm ´ 14 mm ´ 14 mm R Mass (weight) Sensor unit: Approx. 39 g, www.panasonic.net/pcc/support/tel/ excluding the battery homenetwork/manual/ Magnet unit: Approx. 8 g HNS101AZ_(en_en)_0325_ver.031.pdf 2015/03/25...
6) Damage to the product caused by accident, misuse or Act of God. 7) Repairs when the product has been dismantled, repaired, modified or serviced by other than a Panasonic Authorised Dealer authorised to service that type of product. IF YOUR PANASONIC PRODUCT FAILS WITHIN THE...