AT&T U-verse Advance Series A10 Product Manual
AT&T U-verse Advance Series A10 Product Manual

AT&T U-verse Advance Series A10 Product Manual

Advanced series

Advertisement

Quick Links

A. Manual Programming

Use the following steps to set up the TV,
DVD or AUX mode keys:
1. Power on the device you want to
program and locate the 4-digit code
from the code list.
2. Press and hold the mode key (TV,
DVD, or AUX) and while holding it
pressed, press the OK key for one
second.
3. Release both keys and all of the
mode keys will flash then the
selected mode key light will stay lit.
4. Enter the 4-digit code by pressing the
numerical keys (0-9). The selected
mode key light will blink for each digit
entry and will remain off after the entry
of the fourth digit - indicating a
successful set up.
5. Point the remote control at the selected
device and press the power key once.
The device should turn off. If the
device stayed on, repeat the steps 1
thru 4 trying each code for your brand
until you find the correct code.
Repeat above steps to set up another
device.
To use the remote control for your U-verse
unit, press the AT&T mode key.
AT&T U-verse
Advanced Series
NOTE: If an invalid code is entered or no
A10 Remote Control
key is pressed at all for 30 seconds, the
mode key light flashes for 3 seconds and
turns off. The remote control returns to
normal operation and you will need to
start over from step A2 to set up the
device.
NOTE:

B. Using the Search Function

The remote control will only control the
To search for a particular device code for
device which is selected by the
DVD or AUX e.g. VCR, use the Manual
appropriate mode key (AT&T, TV, DVD,
Programming for section A and program
and AUX). The mode key light for the
DVD or AUX with any VCR code prior
selected device flashes each time a valid
to starting a search.
key is pressed.
1. Turn on the device you want to control
Controlling Other Devices
and point the remote at that device.
2. Press and hold the mode key (TV,
In order to control other devices with your
DVD, or AUX) and while holding it
4:1 Universal Remote Control, you need
pressed, press the OK key for one
to tell the remote control what types of
second.
devices you have. Sections A and B bring
3. Release both keys and all of the
you through the steps needed to do this.
mode keys will flash then the
The volume controls will work for the
selected mode key light will stay lit.
device mode you are in. If you want to
4. Press the power button repetitively
change this, you should follow the steps
until the selected device responds.
in Section F.
Once your device has responded, press
OK to save the code.
Programming the remote to control
5. To indicate a successful set up, the
other devices
selected mode key will turn off and you
are ready to set up another device by
To use the U-verse remote control for your
following steps 1 thru 3 of this section.
other devices, you will need to set up the
TV, DVD and AUX mode keys to control

C. Learning

the devices (Section A).
If the code for your device is not found in
Please refer to the code list for a list of
the code list and the search feature does
supported brands and models. If you do
not work with your device, then the
not find the brand of your device on the
learning feature may be your best option.
supported code list, please refer to section
The learning feature lets you "learn"
B for the search function or you may use
functions from your original remote
section C for instructions on the learning
control.
feature of your remote control. If you
have an integrated or combination unit
C-I. Learning Commands
such as a TV/DVD, each component of
the unit may require being set up
1. Press and hold the mode key (TV,
separately by setting up both the TV and
DVD, or AUX) and while holding it
DVD mode keys.
pressed, press the LEARN key for one
second then release both keys.
NOTE: The DVD and AUX mode keys
2. All of the mode keys will flash and
can be set up with any code. The TV mode
then the selected mode key light will
key can only be set up with TV codes.
remain on.
4. Press and release the DELETE key.
The TV mode key light turns off. All
learned Commands in the remote are
now cleared.
3. On your U-verse remote control, press
and release the key that you want to
E. Resetting the remote control to the
teach.
Factory Default Settings
4. While pointing your original remote at
the bottom of your U-verse remote
1. Press and hold the TV key and while
approximately 1 inch apart, press and
holding it pressed, press the OK key
hold the original remote key until the
for one second and release both keys
mode key light blinks once and stays
at the same time.
on. (If there is a learning problem, the
2. All the mode keys will flash and the
mode key light blinks for three seconds
TV mode key light will stay on.
and stays on. If this happens, repeat
3. Press and hold the DELETE key for 3
the steps above.)
seconds until the TV mode LED blinks
and stays off. The remote control is
now reset to factory default settings.
If you want to use the remote control
for your TV and other devices, you will
need to set up the TV, DVD and AUX
AT&T
mode keys.
U-verse
4. If no key is pressed within 30 seconds,
remote
the remote control times out. The
selected mode key light flashes for 3
seconds and turns off. The remote
control returns to normal operation
and you will need to start over.
1 inch

F. Volume Control Set Up Options

apart
The volume controls will work for the
device mode you are in, e.g. if AT&T
mode is selected then volume controls
your AT&T U-verse unit, if TV mode is
selected then volume controls your TV,
Your
etc. If you'd like the volume commands
original
to operate from just one device, e.g.
remote
always TV, then follow the instructions
in Section F-I. If you'd like the volume
commands to be sent to different devices
depending which mode you are in
(Factory Default), then follow the
instructions in Section F-II.
5. Repeat Steps above for each key you
F-I. Volume Always Controls the same
want the U-verse remote to learn.
Device
Press and release the LEARN key when
1. Press and hold the TV key and while
all desired remote commands have been
holding it pressed, press the OK key
learned.
for 1 full second.
2. Release both keys and all of the mode
NOTE:
keys will flash followed by the TV
It is not necessary to have your U-verse
mode key light remaining on.
remote control learn every key from your
3. Press and hold the MUTE key for 3
original remote since most of the keys will
seconds until the TV mode key light
not be used under normal daily use. Best
briefly turns off then remains on. Press
practice is to teach only the keys that help
and release the mode key that you
you navigate for the best experience, like
always want to operate the volume
your volume up and down, channel up
commands (AT&T, TV, DVD, and
and down, and DVR functions.
AUX). The selected mode key light
will remain on.

D. Clearing Commands

4. Press and release the MUTE key to
save the setting. The selected mode key

D-I. To Clear all Learned Commands

light will turn off indicating a
(under a single mode)
successful initial set up. The volume
commands will be set up for the
1. Press and hold the mode key (TV,
selected device despite what mode is
DVD, or AUX) and while holding it
selected. If the selected mode key light
pressed, press the LEARN key for one
flashes for 3 seconds and turns off,
second then release both keys.
then the selected mode will have no
2. All the mode keys will flash and the
volume commands of its own and will
selected mode key light will stay on.
need to start over from step 1 above
3. Press and release the LEARN key
and select a different mode to program
once. The mode key light blinks off.
the device.
4. Press and release the DELETE key.
The mode key light turns off. All
F-II. Volume Control Depends on
learned Commands under that mode
Device Selected (Factory Default)
are now cleared.
1. Press and hold the TV key and while
D-II. To Clear all learned Commands
holding it pressed, press the OK key
(under ALL modes)
for one second.
2. Release both keys and all of the mode
1. Press and hold the mode key (TV,
keys will flash followed by the TV
DVD, or AUX) and while holding it
mode key light remaining on.
pressed, press the LEARN key for one
3. Press and hold the MUTE key for 3
second then release both keys.
seconds until the TV mode key light
2. All the mode keys will flash and the
briefly turns off then stays on.
selected mode key light will stay on.
3. Press and release the LEARN key twice.
The TV mode key light blinks off.
4. Release the MUTE key to save the
H-I. Setting the Clock
setting. The TV mode key light will
turn off indicating successful set up.
Use the +H and +M buttons to set the
The volume commands will now work
Hours and Minutes for the clock. Both
for different devices.
the +H and +M buttons are located at the
bottom on your new Charging Base.
NOTE:
If a programmed mode key has no volume

H-II. Finding more than one remote

commands of its own, then the volume
control will normally operate the TV. If
If there is more than one remote and
an invalid key is pressed, the selected
Charging Base, you can set each Charging
mode key light flashes for 3 seconds and
Base to find only its own remote with 16
turns off. The remote control returns to
unique codes. With the first power up of
normal operation and you will need to
the Charging Base, it will be set to find
start over. If no key is pressed within 30
ALL remotes.
seconds, the remote control times out, the
selected mode key light flashes for 3
To set the Charging Base so that it finds
seconds and turns off. The remote control
a specific remote when there are multiple
returns to normal operation at which time
remote in the household, follow these
you can start over.
instructions:
G. Battery saving backlight
1. Press and hold both clock setting keys
cancellation feature
(+H and +M) at the same time for 3
seconds. The display shows the
In order to extend the life of your battery
current ID, from 1 to 16 or ALL.
between charges, your U-verse remote
2. Press the +M key to cycle from 1 to
control has the ability to toggle between
16 including a selection for all remotes
turning the backlights on or off. If you
in the household.
wish to use this feature, follow these in-
3. Then press the +H key to confirm the
structions.
selection.
1.
Press and hold the TV key and while
To set the remote to the same ID as the
holding it pressed, press the OK key
Charging Base, follow these instructions:
for one second and release both keys
at the same time.
1. Press and hold the TV key and while
2. All the mode keys flash and the TV
holding it pressed, press the OK key
mode key light stays on.
for one second and release both keys
3. Press the GUIDE key and all back-
at the same time. Next press the
lights will no longer turn on.
MENU key to enter ID learn mode
(both the AT&T and AUX lights
To reverse this process so that the back-
remain on).
lights turn on when the remote control is
2. Press the Find key on the Charging
being used, simply follow the same steps
Base – the remote will accept the new
of this section one more time.
ID and the lights will flash once and
then turn off.
H. Charging Base setup
3. To exit this mode without changing the
code, simply press any key.
Connect the Charging Base to the back
of your U-verse set top box via the
H-III. Dimming and brightening the
supplied USB connector or by using the
clock on the Charging Base:
included plug-in power supply. Place the
remote into the Charging Base to charge
Simply pressing and holding the Charging
the rechargeable battery in the remote
Base find key while the remote is in the
control. It takes approximately 12 hours
Charging Base causes the display to dim.
to fully charge the battery in the remote
Holding down the find key until fully dim
but you will be able to use your new
followed by releasing the find key and
remote control within 30 minutes of
holding it down again causes the clock to
charging. To ensure that you have placed
be brighter and return to its original
the remote control on the charging base,
illumination.
the charging indicator located next to the
clock will
show that the battery is being

I. Troubleshooting Learning

charged.
You can only learn one device type under
any one mode key. For example, only
learn TV codes under the TV mode, DVD
codes under the DVD mode, etc. If you
are trying to learn from a "Universal"
remote, it might have more than one code
type stored under a mode.
a. No functions may be stored under the
LEARN key in the AT&T mode.

H. Find feature

b. Depending on the remote you are
trying to learn, some keys may not be
Never lose your remote again! If you have
learnable.
misplaced the remote control and can not
c. Only one original device type can be
locate it, simply press the AT&T globe on
learned per individual mode.
the Charging Base and the remote control
d. Use fresh batteries for your original
will play the AT&T ring tone as well as
remote, and make sure the batteries in
flash several of the remote keys. This
your U-verse remote are fully charged.
should help you locate your lost remote
e. Keep at least three feet away from
control.
incandescent or low-energy lights
when learning.
f. Before learning, clear all learned
commands (refer to Section D-II) then
try learning 2 or 3 commands initially.
Find key
g. Point your original remote at the
Caring for the environment by
bottom end of your U-verse remote so
recycling
the IR elements on both remotes are
This symbol on an AT&T
directly in line with each other (see
product means the product
diagram to the right). You may need
should not be disposed of
to adjust the height of either remote to
with household waste.
achieve this.
h. Avoid learning your original remote's
Disposal of your charging base, power
Volume/Mute keys unless you are sure
supply or remote control.
these operate the same device.
i. Avoid learning your original remote's
VCR or DVD transport keys unless
Please do not dispose of any of the items
in this package with your household
you're sure these operate the same
waste. These items should be disposed of
device.
j. If learning the first or second keys for
accordance with the national collection
a mode results in continuous errors
and recycling schemes operated by your
then try the following:
local or regional authority. Alternatively
you may return unwanted items to any
i. End the learn session by pressing the
approved AT&T Service Center in your
LEARN key.
ii. Clear out the learned commands for
region.
that mode.

Code List

iii. Check the IR elements are correctly
aligned between the two remotes.
TV
iv. Adjust the distance between the two
remotes to be closer (e.g. half an inch)
Abex
or a further away (e.g. 2 inches) from
Acme
each other.
Admiral
0020 0226 0001
v. Try learning the original remote for
Advent
0116 0176 0922
Adventura
that mode again. If problems reoccur
Aiko
with the same key check the original
Aiwa
0195 0196 0227 0269
remote key being learned – does it
Alleron
transmit? Does it operate the target
Amark
device? Try learning that key under a
Amtron
different clear mode. If it learns OK
Akai
0105 0002 0077 1137
1138 0254 1105 1113 1139
then it is likely to be a different code
Anam National
type from the others and cannot be
0025 0042 0193
learned under the same mode.
AOC
0004 0005 0009 1009
0014 0156 0175 0187
FCC Caution
Apex
0214 0216 0215 1132
Archer
THIS DEVICE COMPLIES WITH PART
Aspect
15 OF THE FCC RULES.
Audiovox
0053 1019 1117
Axion
OPERATION IS SUBJECT TO THE FOL-
Bang & Olufsen
LOWING TWO CONDITIONS:
Belcor
(1) THIS DEVICE MAY NOT CAUSE
Bell & Howell
0031 0049 0000 0001
HARMFUL INTERFERENCE, AND
Benq
0081 0083 0101
(2) THIS DEVICE MUST ACCEPT ANY
Bluesky
INTERFERENCE RECEIVED, INCLUD-
Bradford
Broksonic
0147 0135 0310
ING INTERFERENCE THAT MAY
Brokwood
CAUSE UNDESIRED OPERATION.
Candle
0004 0009 0174 0008
Capehart
This equipment generates and uses radio
CCE
frequency energy, and if not installed and
Celera
Celebrity
used properly, that is, in strict accordance
Centrios
with the manufacturers instructions, it may
Centurion
cause interference to radio and television
Cetronic
reception. It has been type tested and found
Changhong
to comply with the limits for remote con-
Cineral
trol devices in accordance with the speci-
Citizen
0004 0009 0053 0105 0109
fications in Sub-Parts B and C of Part 15
0189 0135 0001 0008 0042 0058
Clairtone
of FCC Rules, which are designed to pro-
Classic
0214 0401 0042
vide reasonable protection against such in-
Coby
terference in a residential installation.
Color Voice
However, there is no guarantee that inter-
Colortyme
0004 0009 0010
ference will not occur in a particular in-
Concerto
stallation. If this equipment does cause in-
Concierge
Contec/Cony
0053 0012 0014 0042
terference to radio or television reception,
Cornea
which can be determined by unplugging
Craig
the equipment, try to correct the interfer-
Crosley
ence by one or more of the following mea-
Crown
sures.
Curtis Mathes
0031 0105 0130 0004
0009 0000 0049 0109 0358 0001 0015
CTX
• Reorient the antenna of the radio/TV
CXC
experiencing the interference.
Cybervision
• Relocate the equipment with respect to
Daewoo
0130 0004 0009 0100 0005
the radio/TV.
0138 0043 0140 0039 0444 0080 0042
• Move the equipment away from the ra-
0058 0017 0010 0126 0018 0127 0019
dio/TV.
Daytron
Dell
0209 0028 0132
• Plug the equipment into an outlet on a
Diamond Vision
0210 0948 0092
different electrical circuit from the ra-
Digimate
dio/TV experiencing the interference.
Digistar
1019 0165 0118 0116
• If necessary, consult your local dealer
0167 0132 1020 1151 1152
for additional suggestions.
Dimensia
The manufacturer is not responsible for
any radio or TV interference caused by un-
authorized modifications to this equipment.
Such modifications could void the user's
authority to operate the equipment.
0185
0010
0174
0058
0051
0020
0053
0053 0003
0020
0059
0177
0190
0004
1155 0144
0053
0004
0175
1153
0214
0002
0169
0009
0042
0214 0401
0058 0144
0014
1091 1124
0010
0004 0009
0121
0050
0053 0042
0062
0053 0042
0020
0053 0042
0144
0004 0009
1017
0031 0000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the U-verse Advance Series A10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for AT&T U-verse Advance Series A10

  • Page 1 3. On your U-verse remote control, press and release the key that you want to A. Manual Programming teach. 4. While pointing your original remote at Use the following steps to set up the TV, the bottom of your U-verse remote DVD or AUX mode keys: approximately 1 inch apart, press and hold the original remote key until the...
  • Page 2 Semp Sharp Shogun Memorex 0004 0009 0049 0051 0135 Signature 0031 0000 1007 0268 0310 0001 Simpson 0004 0005 0009 0051 TV (continued) Sonic 0012 0022 0141 0180 Sony Midland 0031 0121 0054 0107 0015 Disney 0158 0135 Mintek 0146 Dukane 0059 0072 Sova...

Table of Contents