Others - Panasonic SC-PMX9DB Operating Instructions Manual

Others

Decrease the brightness of the display panel
1
Press [SETUP] to select "Dimmer".
2
Press [2, 1] to select "On" and then press [OK].
Note:
• To cancel, select "Off" in step 2.
Automatically switch off the system
This function switches off the system (except in radio
source) if you do not use the system for approximately
20 minutes.
1
Press [SETUP] repeatedly to select "Auto Off".
2
Press [2, 1] to select "On" and then press [OK].
Note:
• To cancel, select "Off" in step 2.
• When connected to a Bluetooth ® device, this function does
not work.
• If "Net Standby" is set to "On", this function will also be set
to "On". To change the setting, set "Net Standby" to "Off".
( right)
Software update
Occasionally, Panasonic may release updated software
for this system that may add or improve the way a
feature operates. These updates are available free of
charge.
DO NOT DISCONNECT the AC mains lead while
one of the following messages is displayed.
– "Linking", "Updating" or " %"
(" " stands for a number.)
• During the update process, no other operations can be
performed.
Preparation
• Turn this system on.
• Connect this system to the home network. (
– Make sure that the network is connected to the
Internet.
– If "D.Connect" is set to "On", change the setting to
"Off" and connect this system to a network that is
connected to the Internet.
1
Press [SETUP] repeatedly to select "SW Update"
and then press [OK].
2
Press [2, 1] to select "Update? Yes" and then
press [OK] to start the update.
• Select "Update? No" to cancel the update.
{. After the update has finished, "Success" is displayed.
3
Disconnect the AC mains lead and reconnect it
after 3 minutes.
• If there are no updates, "No Need" is displayed.
• Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
∫ Checking the software version
1 Press [SETUP] repeatedly to select "SW Version" and
then press [OK].
{. The version of the installed software is displayed.
2 Press [OK] to exit.
Wi-Fi signal strength
To check the Wi-Fi signal strength where this system is
located.
Preparation
Connect this system to the wireless network. (
1
Press [SETUP] repeatedly to select "Signal
Level" and then press [OK].
• This system's displays show "Level ".
(" " stands for a number.)
2
Press [OK] to exit this display mode.
• It is recommended to have a signal strength of "3". Change
the position or angle of your wireless network router or this
system if the indication is "2" or "1" and see if the
connection improves.
• If "Level 0" is displayed, this system cannot establish a link
with the wireless network router. (
• This function does not work when "D.Connect" is set to
"On".
Wireless LAN setting
6)
The wireless LAN function can be enabled or disabled.
1
Press [SETUP] repeatedly to select
"Wireless LAN" and then press [OK].
2
Press [2, 1] to select "On" or "Off" and then
press [OK].
• The factory preset is "On".
Network standby
This system can turn on automatically from standby mode
when this system is selected as the AirPlay speakers.
Preparation
Connect this system to the home network. (
1
Press [SETUP] repeatedly to select
"Net Standby" and then press [OK].
2
Press [2, 1] to select "On" and then press [OK].
• To cancel this function, select "Off" in step 2.
• The factory preset is "Off". If this function is set to "On" the
standby power consumption will increase.
Wireless network name (SSID)
Display the name for the connected wireless network
(SSID).
1
Press [SETUP] repeatedly to select "Net Info"
and then press [OK].
"IP Addr." is indicated on the display.
2
Press [SETUP] repeatedly to select "SSID" and
then press [OK].
3
6) Press [OK] to exit.
• If "No Connect" is displayed this system is not connected to
a wireless network.
• All letters are displayed as capital letters, and characters
that cannot be displayed are replaced with "
IP/MAC Address
To check this system's IP address or the Wi-Fi MAC address.
1
Press [SETUP] repeatedly to select "Net Info"
and then press [OK].
"IP Addr." is indicated on the display.
17)
2
Press [SETUP] repeatedly to select "IP Addr." or
"MAC Addr."and then press [OK].
The IP address or the MAC address is partially
displayed.
3
Press [2, 1] on the remote control to show the
rest of the IP address or the MAC address.
• To exit the setting, wait 20 sec.
• The " – " displayed on the top or bottom left of the display
indicate the first and last units respectively.
6)
¢ ".
15