Cd Test Mode - Pioneer deh-1100mp Service Manual

5

6.2 CD TEST MODE

QQ
3 7 63 1515 0
- Flow Chart
[Key]
Contents
Display
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TRK MIN SEC
[BAND]
Power Off
TE
L 13942296513
TRK MIN SEC
*1) TYP
TRK MIN SEC
*2) Focus Close → S Curve check setting → F EQ measurement setting
TRK MIN SEC
00 00 00
TRK MIN SEC
( 99 99 99)
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the
*4) 1TR/4TR/10TR/32TR/100TR
→ 4TR → 10TR → 32TR → 100TR → CRG Move
*5) Single
9x(8x):91(81) 92(82)
*6) Only at the time of CRG move, 100TR jump
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
*8) CRG motor voltage = 2 [V]
*9) TYP (1X)
TRK MIN SEC
www
• As for the double speed (2x), audio output cannot be supported
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
.
sticks to Wall, causing the actuator to be damaged).
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
5
http://www.xiaoyu163.com
6
[4] + [6] + Reset or
[4] + [6] + BU + ACC
Test Mode In
[CD] or [SOURCE]
Source On
TRK MIN SEC
[BAND] [3]
Power On Power On
(T.Offset is adjusted) (T.Offset is not adjusted)
TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99
[3] [6]
Focus Close Focus Mode switching
*2
S curve check
TRK MIN SEC TRK MIN SEC
91 91 91 0X 0X 0X
[1] [6]
T.Close & AGC
T.Close
Applicable servomechanism
Applicable servomechanism
TRK MIN SEC TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec
[1] [3]
*7
F,T,RF AGC F,T AGC / F.Bias
F.Bias display switching RF AGC
TRK MIN SEC TRK MIN SEC
?? ?? ?? ?tr ?min ?sec
→ →
+ 6 dB + 12 dB
TRK MIN SEC TRK MIN
06 06 06 12
TRK MIN SEC TRK
01 01 01 02
order of the original display
93(83) 94(84) 95(85)
→ →
2X 1X
TRK MIN SEC TRK MIN
22 22 22 11 11
x ao u163
y
i
6
http://www.xiaoyu163.com
2 9
8
[2] [4]
*1 *9
RF AMP SPINDLE
Gain switching Speed switching
TRK MIN SEC TRK MIN SEC
GG GG GG SP SP SP
[1] [>]
Tracking Servo CRG +
*8
Close
00 00 00 00 00 00
or 99 99 99 or 99 99 99
[3] [>]
RF AGC / CRG +
RF AGC coefficient display
TRK MIN SEC 8X 8X 8X
?? ?? ?? or 9X 9X 9X
*5
[6] [>]
CRG/TR jump CRG/TR Jump +
*4
value switching
TRK MIN SEC TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec
Q Q
3 6 7 1 3 1 5
SEC
[Key]
12 12
[BAND] Power On/Off
CRG + / TR Jump +
[>]
(Direction of the external surface)
MIN SEC
02 02
CRG - / TR Jump -
[<]
(Direction of the internal surface)
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
[2] RF Gain switching / Offset adjustment display /
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
F,T,RF AGC
SPDL 1X/2X switching
[4]
As for the double speed(2x), audio output cannot be
96(86)
supported.
Error Rate measurement
[5]
[6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*10) OFF(TYP)
SEC TRK MIN SEC
11
co
.
DEH-1100MP/XN/UC
7
9 4 2 8
[<] [2]
CRG - Self-adjusting
*8 *3
switching
Gop Mode switching
00 00 00 TRK MIN SEC
or 99 99 99 ?? ?? ??
[<] [2]
CRG - T.Balance adjustment /
T.BAL coefficient display
8X 8X 8X TRK MIN SEC
or 9X 9X 9X ?? ?? ??
[<] [2]
CRG/TR Jump - Tracking Open
*4
8X 8X 8X
TRK MIN SEC
?tr ?min ?sec or 9X 9X 9X
*6
[2]
Tracking Open
0 5 8 2 9 9 4
8X 8X 8X
or 9X 9X 9X
Operation
Test Mode
ON : ERR 30Counts Start
BER display data[%]
→ →
FORCUS TRACKING
TRK MIN SEC TRK
70 70 70 71
m
7
8
9 9
A
B
[5]
Gop Mode *10
TRK MIN SEC
OL OL OL
C
2 8 9 9
D
E
MIN SEC
71 71
F
23
8