Konica Minolta bizhub 363 Installation Manual page 9

<Main Scanning (Front)/ Main Scanning (Back)>
Note:
For the 423 machine or the 363 machine that
comes with the ADF as standard, perform this
adjustment during their installation if necessary.
For the 363 machine that does not have the ADF
as standard or the 283/223 machines, follow the
ADF installation manual and perform the adjust-
ment during the ADF installation.
14. Place the chart in the document feeding tray
(with the side having an arrow facing up).
A01HIXC011DC
15. Make full size copies.
16. Place the chart in the document feeding tray
(Make sure that the blank surface of the chart
faces up).
A1DMIXC005DA
17. Make full size copies.
* Make copies in duplex mode.
18. Check whether the difference in the width A
between the chart and the copy sample is within
the specified range.
Difference in the width A = A of the copy sample
– A of the chart
Specifications: 0 ± 2.0 mm
* If the difference in the width A does not fall within
the specified range, perform the following
adjustment.
A1DMIXC016DA
19. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
20. Touch "ADF."
21. Touch "Original Stop Position."
22. Touch "Main Scanning (Front)" or "Main Scan-
ning (Back)."
23. While looking at the copy sample, enter a value
using the ten-key pad. (To switch the signs,
press the +/- key.)
Adjustable range: -3.0 mm to +3.0 mm
(0.1 mm per step)
If the difference in the width A is greater than the
specifications, enter a positive (+) value.
If the difference in the width A is smaller than the
specifications, enter a negative (-) value.
24. Touch "END."
25. Touch "Exit" on the Service Mode screen.
26. Make copies again and check the difference in
the width A.
XX. Date/Time setting
1. Make sure that the Service Mode screen is dis-
played.
2. Display the Date & Time Setting screen.
(To display the Date & Time Setting screen, press
Stop → 1 → 1 → 4 → 4 → Clear on the control
panel.)
3. Press the clear key.
4. Enter the data for the year, month, day, and time-
of-day from the 10-key pad.
5. Touch "Entry."
Note:
Touching the Entry key returns the figures in the
Date & Time Setting screen to 0 and Date & Time
Setting has been completed.
6. Touch "END."
7. Touch "Exit" on the Service Mode screen.
8. Select the Date/Time Setting function as follows:
Utility/Counter → Administrator Settings → Enter
the Administrator Password (Default setting:
12345678) → System Settings → Date/Time Set-
tings.
9. Select the item you want to set and press the
clear key.
10. Enter the data for the year, month, day, and
time-of-day from the 10-key pad.
11. Touch "OK."
12. Touch "Close" three times.
XXI. Install date
1. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
2. Select the Install Date function as follows:
System 1 → Install Date.
3. Press the clear key.
4. Enter the data for the year, month, and day from
the 10-key pad.
5. Touch "Entry."
Note:
Touching the Entry key returns the figures in the
Install Date screen to 0 and Install Date has been
completed.
6. Touch "END."
E-9
XXII. Serial number input
Note:
Serial number input is needed only for optional
devices that will be installed later.
1. Select the Serial Number Input function as fol-
lows: System 1 → Serial Number.
2. Touch the item you want to enter and input the
serial number.
3. Touch "END."
4. For other devices, enter their serial number in the
same way.
5. Touch "END."
XXIII. Unit change
Note:
This function allows the user to select the type of
message that will appear when the replacement
time arrives for each of the different units.
1. Select the Unit Change function as follows:
System 2 → Unit Change.
2. Select the appropriate message type for each
unit.
3. Touch "END."
XXIV. List output
1. Load the tray 1 with A4 or Letter paper.
2. Touch "List Output."
3. Check that "Machine Management List" is
selected and press the start key.
The list will be output.
4. Output "Adjustments List" in the same way.
5. Touch "2."
6. Check that "Service Parameter" is selected and
press the start key.
The list will be output.
7. Touch "END."
Note:
If installing paper feed options is unnecessary,
touch "Exit" on the Service Mode Screen.