quick start guide
Keep in mind!
How to turn on the power switch?
▶
When you initially purchase the product,
the power switch will be kept off.
Turn on the power switch at the bottom
of the robot cleaner. All functions will
work only when the power switch is
turned on.
When you turn the power switch off and then on,
all settings will be reset.
NOTE
Battery is naturally discharged!
▶
When you separate the robot cleaner from the charger,
the battery will naturally be discharged. Therefore keep
the cleaning robot on the charger, if possible.
If no key is pressed for approximately 5 minutes after
turning the power on, the power is automatically cut to
NOTE
prevent the battery discharging.To turn the power on
again, press and hold the power (Run/Stop) button on the
main body or on the remote control for a short while.
Auto charge is not smooth!
▶
When you execute the cleaning mode while the cleaning
robot is charged on the charger, it will return to automatically
charge more quickly and accurately.
1. In the following cases, lift the cleaning robot with your
hand and put it on the charger to charge it.
- When the charger is installed in a corner
- When the battery is fully discharged
- When the cleaning robot is trapped with an obstacle
- When the cleaning robot cannot pass over the doorsill to
the location where the charger is installed
2. When the charger and the cleaning robot are in separate
rooms, it could take a long period of time to automatically
charge the robot.
3. Check the installed condition of the charger.
(Refer to Installing the charger)
4. Wipe the obstacle sensor window lightly with a soft cloth.
To test the auto Homing, press the Charge button when the
cleaning robot is within 1.5M of the charger.
NOTE
The cleaning robot cannot cross over the doorsill!
The robotic vacuum cleaner's innovative
driving system makes it possible for it to
About 1.5 cm
About 1.5 cm
Stair type
Stair type
Vertical type
Vertical type
cross over doorsills with a height of
about 1.5 cm and clean all rooms.
The robotic vacuum cleaner may not be able to pass a 1.5
cm doorsill depending on the shape of the doorsill.
What do I do when the suction power is low
or the noise level is high?
▶
Clean the dust bin and filter.
▶
Clean the power brush.
The cleaning robot hits the obstacles such
as wall, furniture etc.
▶
The cleaning robot can bump into chair
legs, table legs, sofa etc. during the
operation. Put the chair on top of the
table while cleaning.
DJ68-00674N-1 EN.indd 1
DJ68-00674N-1 EN.indd 1
The cleaning robot is not able to clean the
corners!
▶
Because the cleaning robot cannot completely
clean the tight corners, wall between the sofas you
should regularly clean
those areas.
There is a weird noise!
▶
After turning off the power switch on the bottom, flip the
cleaning robot and remove any foreign substances
(Paper, vinyl) on the power brush or air pump.
Charging time is too long!
▶
If you charge the cleaning robot when the battery is heated
after the cleaning, the charging time could take longer.
Troubleshoting for Error Codes
ERROR
CAUSE
CODE
•
Robotic vacuum
cleaner is caught,
stuck or trapped while
navigating.
•
A foreign substance
(string, paper, toy
etc.) is caught in the
power brush.
•
A foreign substance
(string, paper, toy
etc.) is caught in the
left driving wheel.
•
A foreign substance
(string, paper, toy
etc.) is caught in the
right driving wheel.
•
Check bumper
sensor.
•
A foreign substance
(dust, stain etc.) is
on the Obstacle
sensor window.
•
A foreign substance
(Dust, stain etc.) is
on the Cliff sensor
window.
•
Dust bin not
inserted.
A foreign substance
•
(String, cloth etc.)
is caught on the
edge-cleaning side
rotating brush.
✽ If you press the Start/Stop button or turn off the Power
Switch, the error code is cleared.
Code No. DJ68-00674N REV(0.0)
SR8875
SOLUTION
•
Turn off the Power Switch
at the bottom and move
the robotic vacuum cleaner
to a different location.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the power brush.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the left driving wheel.
•
Turn off the Power Switch
at the bottom and remove
the foreign substance from
the right driving wheel.
•
Slightly pull the stuck
bumper outward.
•
Turn off the Power Switch
at the bottom and wipe
the foreign substance from
the front and rear sensor
windows using a soft cloth.
•
Turn off the Power Switch
at the bottom and wipe the
foreign substance on the
cilff sensor window with a
soft cloth.
•
Insert the dust bin until you
hear a "Click" sound.
•
Turn off the Power Switch
at the bottom and wipe
the foreign substance
from the edge-cleaning
side rotating brush.
English
13. 01. 09 오후 8:14
13. 01. 09 오후 8:14