Important Safety Instructions RISK OF ELECTRIC SHOCK DO NOT OPEN APPLICABLE FOR USA, CANADA OR WHERE RISQUE DE CHOQUE ÉLECTRIQUE N'OUVREZ PAS APPROVED FOR USAGE CAUTION: TO PREVENT ELECTRIC SHOCK, CAUTION: To reduce the risk of electric shock, do not remove cover (or back). MATCH WIDE BLADE PLUG TO WIDE SLOT, No user-serviceable parts inside.
Table of Contents Important Safety Instructions ....................2 Introduction ..........................4 Features ................................. 5 What’s Included ............................5 D2.1 Inputs & Outputs ....................... 6 D2.1 Side Vents .......................... 7 D2.1 IR Remote .......................... 8 Installation ..........................9 Shelf Mount ..............................9 Wall Mount ..............................
D2.1 will also team up nicely with other branded speakers...when those situations are just unavoidable. Are you a bass freak? If so, the D2.1 has a line level subwoofer output that can be used to drive an Xpress subwoofer amplifier and subwoofer for additional bass extension and pres- ence.
Digital Optical Audio Input • Bluetooth Compatible (audio and control) • Line Level Subwoofer Output (RCA) • 5VDC power supply output for Xpress Accessories • 10 Band Graphic EQ • Adjustable High-Pass or full range speaker settings • Adjustable Subwoofer crossover frequency, slope and phase settings •...
AC Power Cord to an unswitched AC power outlet. 2. IR SENSOR - IR sensor ‘sees’ the IR commands from the D2.1 IR Remote, or other properly configured programmable remote to control D2.1 Power, Volume, EQ Input, etc.
9. USB - Provides 5VDC to Xpress Accessories. D2.1 Side Vents Even though the D2.1 will typical run cool, the side vents allow air to circulate through the chassis allowing optimum performance, and besides...they just look cool...get it...air vents... look cool...never mind...
D2.1 RJ45 Receiver IN jack. Press ►► to forward scan the current track. 11. INPUT SELECT - IN 1 - Press to select the source connected to the D2.1 L&R Line Level IN 2 - Press to select the source connected to the D2.1 Optical IN.
Shelf SHELF MOUNT The D2.1 can be conveniently mounted on a shelf top as shown. Use wood screws to secure the amp to the shelf to avoid having the amp slide off the shelf and possibly damage the amp, connected cables or other equipment. Leave room for wires. Allow adequate space for airflow.
All connections are conveniently placed on the side panel for sane wire management, conve- nient connections and simple service. The illustration shows the D2.1 in a typical home entertainment system for TV audio with stereo in ceiling speakers with a subwoofer amp and subwoofer.
OPTICAL IN (TV AUDIO CONNECTION) 1. Using a Digital Optical Audio cable, connect the Digital Optical Audio OUT on the TV (or other source) to the Optical IN on the D2.1. To select this input, press IN 2 on the D2.1 IR Remote.
Press again to turn Night Mode OFF. SOURCE SELECT IN 1 - Press to select the source connected to the Line L&R jacks on the D2.1. IN 2 - Press to select the source connected to the Digital Optical jack on the D2.1.
Module. This device will not only allow you to stream your favorite audio content via Bluetooth from almost any current Bluetooth device to the D2.1, but it will also allow IR control of D2.1 functions, (source select, volume, mute, EQ etc) but also allow IR control of most current Bluetooth devices using either the D2.1 IR Remote or other properly...
3. Status LED will turn ON. POWER 1. Press the Power button on the D2.1 IR Remote. The Status LED will flash once and turn OFF. 2. Press the button on the system remote to be used for turning the D2.1 ON/OFF.
5. To exit Learning Mode, press IN 1, otherwise press the next button to be learned. INPUT 3 SELECT 1. Press the IN 3 button on the D2.1 IR Remote. The Status LED will flash once and turn OFF. 2. Press the button on the system remote to be used for IN 3.
Specifications AUDIO Maximum Output Power per Channel ....................50W THD+N ................................. <0.5% Signal to Noise (RCA/Bluetooth) ......................78dB Signal to Noise (Optical) ...........................90dB Input Sensitivity ............................. 500mV GENERAL DC Power Supply Output ......................+5VDC/0.5A Line Voltage Range ........................100~240 VAC Standby Power ...............................1W Dimensions ..........5.3”W x 6.9”H x 2”...
This warranty shall not apply to products which have been abused, modified, disassembled, or repaired by anyone other than Xpress or one of its appointed service centers. Products to be repaired under this warranty must be returned to the factory or designated service center with all transportation and insurance charges pre-paid.