Messages On The Display; Optical Message; What To Do In The Event Of A Fault; Fault Codes - Nespresso Romeo Instructions For Use Manual

Table of Contents

Advertisement

G
Empty, clean and re–insert drip tray 14
and capsule container 15.
G
Fill the water tank 8 with fresh water.
Display 5 : Ready
The descaling alarm is automatically can-
celled.
G
Wipe the outside of the appliance with a
damp cloth.
If the descaling process is terminated, the
descaling alarm is not cancelled and the
appliance prompts the customer to carry
out a complete rinsing procedure according
to the instructions on the display.
If inadequate descaling solution or fresh
rinsing water was used, the appliance
goes back one step and the display
prompts the customer to add descaling
solution or water again.
Manually resetting the Needs to
be descaled display
If a manual descaling procedure is run, the
Needs to be descaled display can be can-
celled on display 5.
G
Hold down button
P 4 for three seconds.
G
Select Descaling alarm reset ? with button
P 4.
G
Select Yes with button
-2 or button
+3.
G
Press button
1. The Needs to be
descaled display is cancelled.
Important
The appliance must be descaled regularly,
otherwise it will be damaged.

Messages on the display

Fill and Water flash alternately on display 5
G
The water tank 8 is empty.
Fill with frFesh water.
However, one more cup can be drawn.
Important : If the appliance signals Fill
and Water even though the tank is full,
see the chapter on «What to do in the
event of a fault».
Empty and Capsules flash alternately on
display 5.
G
The capsule container 15 is full.
Dispose of the used NESPRESSO
cap-
®
sules (Fig. 6).
Check and Container flash alternately on
display 5.
G
The drip tray 14 and capsule container
15 are missing. Correctly insert the drip
tray 14 and capsule container 15.
Power save lights up on display 5.
G
The appliance switches automatically to
Power save if it was not used for one
hour.

Optical message

Float 16 rises.
During the rinsing process and when coffee
is being made, a little water runs into the
drip tray 14. When the tray is full, the float
rises (Fig. 6).
G
Pull the drip tray 14 forwards.
G
Remove the capsule container 15.
10
G
Empty the drip tray 14 and rinse with a
little detergent solution.
G
Place the capsule container 15 on the
drip tray 14 and re–insert.
What to do in the event
of a fault ?
The appliance is not functioning.
G
Check whether there has been a power
failure or the main plug has been
pulled out.
Hot water or steam cannot be drawn.
G
The nozzle 13 is blocked. Clean the noz-
zle 13 with a detergent solution and a
blunt needle.
Milk froth is too little or too runny.
G
The CAPPUCCINO/CAFFELATTE frothing
device 12 is blocked. Clean with a mild
detergent solution according to the
instructions.
G
Use cold, semi–skimmed milk.
Message on the display Fill // Water
despite full water tank
G
Check whether the water tank 8 is calci-
fied. If required, descale water tank 8.
G
The appliance is not detecting the water
level. Condensation may be forming on
the tank wall, then fill up the water tank.
If the water tank 8 is scratched, rotate
the tank slightly.
If the message is still displayed, please
order a new tank.

Fault codes

Risk of electric shock
Pull out the mains plug immediately if one
of the fault codes F1 to F10 lights up.
Fault
Remedial action
code
F1,F2,
Electrical malfunction.
F4, F6,
Pull out main plug and re-
F7, F9
insert after approx. 5 seconds.
F 3
Mechanical malfunction.
Pull out mains plug and proceed
F 5
as follows :
A capsule may have been left
connected near the brewing
F 8
unit. Remove and empty the
capsule container 15. If no cap-
sule was found, pull out the
main plug. Push in the ledge 20
as far as possible (Fig. 10). The
capsule could block the ejector
or the brewing unit. If the cap-
sule can be seen, carefully con-
vey it with a spoon into the cap-
sule container 15. When the
capsule has been removed,
switch on the appliance again.
F 10
Electrical malfunction or missing
capsule support 19.
Check that the capsule support
has been inserted correctly.
If the fault code lights up again when
the appliance has been switched on,
call the Hotline : 800-562-1465.
11

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents