1. Manuals
  2. Brands
  3. Quantum Manuals
  4. Wheelchair
  5. edge 2.0
  6. Owner's manual

Quantum edge 2.0 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Quantum edge 2.0

Summary of Contents for Quantum edge 2.0

  • Page 1 Owner’s Manual...
  • Page 2 On the product, this icon is represented as a black symbol with a red circle and red slash. Intended Use The intended use of the Quantum Rehab device is to provide mobility to persons limited to a seated position that have the capability of operating a powered wheelchair.

  • Page 3: Table Of Contents

    NOTE: This product meets IPX4 classifi cation (IEC 60529). NOTE: The Q6 Edge 2.0 and its components are not made with natural rubber latex. Consult with the manufacturer regarding any after- market accessories.
  • Page 4 Identifi cation Key ...
  • Page 5 Identifi cation Key  Seat Assembly Armrest Seatback Seat Base Controller Joystick Trapeze Bar Location Power Base Assembly Rear Shroud (If Equipped) Spring Shock/ Drive Wheel Manual Freewheel Lever Gas Damper Location Front Rigging Caster Wheel Front Shroud (Foot Platform Shown)

  • Page 6: Introduction

    Quantum to enhance or preserve the safe use of this product.

  • Page 7: Safety

    Safety  Product Safety Symbols The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. NOTE: There are more warnings identifi ed and explained in the Consumer Safety Guide that is included with your power chair.
  • Page 8 The contents of this manual are based on the expectation that a mobility device expert has properly fi tted the power chair to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Provider in the instruction process for the use of the product.
  • Page 9  Check the brakes. See “Care and Maintenance.”  Check battery charge. See “Batteries and Charging.”  Ensure the manual freewheel levers are in drive mode before sitting on the power chair. NOTE: If you discover a problem, contact your Quantum Rehab Provider for assistance.

  • Page 10: Your Power Chair

    Your Power Chair  The Q6 Edge 2.0 Power Chair Your power chair has two main assemblies: the seat assembly and the power base assembly. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/ brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses.
  • Page 11 3. Controller Connector 8. Suspension Spring 4. To Battery Connectors 9. Fender Light Connector 5. To Motor Connector (Optional) 6. Main Circuit Breaker Figure 1. Q6 Edge 2.0 Electrical Components Freewheel Mode Drive Mode Figure 2. Manual Freewheel Lever Operation...
  • Page 12 Your power chair may be equipped with the iLevel® feature that will be used in conjunction with your TRU-Balance® 3 Power Positioning System. The iLevel® feature is mounted on a Quantum power base for maximum stabil- ity when the seating system is elevated. See fi gure 3.
  • Page 13  Single Switch iLevel® Boot (1 of 2 shown) Q-Logic 2 Controller NE+ Controller iLevel® engaged iLevel® not iLevel® engaged engaged iLevel® not engaged Figure 3. Q6 Edge 2.0 with iLevel® Feature and Controller Indicators...
  • Page 14 WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specifi c requirements.
  • Page 15 25% when elevated. If this warning appears while on level ground, please discontinue use of iLevel® feature and consult your Quantum Rehab Provider for assistance. Fender Lights (Optional) Your power chair may be equipped with fender lights. The lights are com- posed of three white LEDs in the front and three red LEDs in the rear and are mounted on the fenders of your power base.
  • Page 16  Single Switch Fender Light (1 of 2 shown) Figure 4. Q6 Edge 2.0 with Single Switch to operate Fender Lights To activate the fender lights using the controller/single switch com- bination: 1. Turn on the power to the controller.
  • Page 17  If operated through the controller/single switch combination, the fender lights will turn on when the power chair is turned on and the joystick is de- fl ected in any direction. The power chair must remain powered on for the lights to stay illuminated.

  • Page 18: Assembly

    fi t. Replacement nylon insert lock nuts are available at local hardware stores or through your Quantum Rehab Provider. Seat Installation It may be necessary to install the seat either prior to initial operation or after transporting your power chair.
  • Page 19  MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie-down points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways....
  • Page 20 4. Foot Platform Height/Depth 2. Controller Position Adjustment 3. Foot Platform Angle Adjustment Figure 5. Q6 Edge 2.0 Assembly View Identifi cation Key 1. Rear Extrusion 3. Front Extrusion 2. Seat Latch Safety 4. Trapeze Bars Figure 6. Universal Mounting System and Contour Seat...
  • Page 21  Identifi cation Key 1. Wire Ties 2. To Power Base Figure Controller Harness Figure Controller Harness Routing on a TRU-Balance® 3 Routing on a Contour Seat Identifi cation Key Identifi cation Key 1. Seat Plate Interface Bracket 1. Securement Brackets (2 of 4 2.

  • Page 22: Comfort Adjustments

    WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specifi c requirements.
  • Page 23  4. Flip up the seat latch safety. See fi gure 6. 5. Squeeze the seat latch and release the seat from the front trapeze bar. 6. Slide the seat forward and remove it from the power base. 7. Remove the hardware that attaches the trapeze bars to the seat interface weldments.
  • Page 24  Identifi cation Key Identifi cation Key 1. Seat Interface Weldment 1. Seat Mounting Holes 2. Trapeze Bars 3. Hardware Figure 11. Seat Height/Angle Figure 12. Seat Position Adjustment Adjustment Seatback Angle Adjustment If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90, 102, 105, or 107.
  • Page 25  To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See fi gure 13. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. Armrest Angle Adjustment To change the armrest angle: 1.
  • Page 26  Identifi cation Key 1. Jam Nut 5. Armrest Knob 2. Armrest Angle Adjusting Screw 6. Controller Bracket 3. Armrest Height Adjusting Screws 7. Setscrew 4. Seatback Angle Adjusting Screw Figure 13. Seatback/Armrest Adjustment 9. Tighten the setscrews in both armrests. 10.
  • Page 27 NOTE: For more information on operating the power elevating seat through the controller, contact your Quantum Rehab Provider. WARNING! The power elevating seat option is intended for use on a level surface only. Never raise the seat from its lowest position on an inclined surface.
  • Page 28  Identifi cation Key 1. Foot Platform Bracket 2. Hardware 3. Screw Figure 14. Foot Platform Adjustment Figure 15. Power Elevating Seat Toggle Switch NOTE: The power elevating seat option is equipped with a system that reduces the speed of the power chair to one quarter when the seat is elevated.
  • Page 29 MANDATORY! Inspect the positioning belt for loose parts or damage, including tears, worn spots, bent hardware, damaged latch mechanisms, dirt or debris, before each use of the power chair. If you discover a problem, contact your Quantum Rehab Provider for maintenance and repair. Figure 16. Positioning Belt Adjustment...

  • Page 30: Batteries And Charging

    Batteries and Charging  Batteries and Charging The Q6 Edge 2.0 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fl uid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge.
  • Page 31  WARNING! Inspect the battery charger, wiring, and connectors for damage before each use. Contact your Quantum Rehab Provider if damage is found. WARNING! Do not attempt to open the battery charger case. If the battery charger does not appear to be working correctly, contact your Quantum Rehab Provider.
  • Page 32 NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero voltage. If this happens, call your Quantum Rehab Provider for assistance. How often must I charge the batteries? Many factors come into play when deciding how often to charge the batteries.
  • Page 33   Daily Use If you use your power chair on a daily basis, charge the batteries as soon as you are fi nished using your power chair. Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the batteries at least 8 to 14 hours after daily use.
  • Page 34 We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specifi c demands. Fresh batteries arrive regularly at Quantum and are promptly shipped with a full charge. During shipping, the batteries encounter temperature extremes that may infl uence initial performance.
  • Page 35  What about public transportation? AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s specifi...

  • Page 36: Care And Maintenance

    Care and Maintenance  Care and Maintenance Your Q6 Edge 2.0 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Provider.
  • Page 37 Check the rubber boot around the base of the joystick for damage. Visually inspect the boot. Do not handle or try to repair it. See your Quantum Rehab Provider if there is a problem.
  • Page 38 Monthly Checks  Check for drive tire wear. See your Quantum Rehab Provider for repair.  Check the caster wheels for wear. Replace them as necessary.  Check the caster forks for damage or fl uttering which indicates that they may need to be adjusted or have the bearings replaced.
  • Page 39 Provider for repair. Yearly Checks Take your power chair to your Quantum Rehab Provider for yearly maintenance, especially if you use your power chair on a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.
  • Page 40 Quantum Rehab Provider. WARNING! The wheels on your power chair should only be serviced or replaced by a Quantum Rehab Provider or a qualifi ed technician. WARNING! Be sure that the controller’s power is turned off and the power chair is not in freewheel mode before performing this procedure.
  • Page 41 Identifi cation Key 1. Lug Nuts 2. Wheel Hub Figure 18. Q6 Edge 2.0 Drive Wheel Identifi cation Key 1. Front Rim Half 4. Rear Rim Half 2. Tube 5. Screws 3. Tire Figure 19. Q6 Edge 2.0 Drive Wheel Disassembled...
  • Page 42 WARNING! The batteries in your power chair should only be serviced or replaced by a Quantum Rehab Provider or a qualifi ed technician. WARNING! Do not replace batteries when seat is occupied. WARNING! Power chair batteries are heavy. See specifi cations table. If you are unable to lift that much weight, be sure to get help.
  • Page 43  Identifi cation Key 1. Quick Release Battery 4. Front Cover Connectors 5. Release Handles 2. Rear Battery 6. Battery Wiring Diagram 3. Front Battery Label Battery Seat Confi guration: + = Positive (Red) Terminal Post - = Negative (Black) Terminal Post Connect Red wire to Red Positive (+) Terminal Posts.
  • Page 44 When to See Your Quantum Rehab Provider for Service The following symptoms could indicate a serious problem with your power chair. If necessary, contact your Quantum Rehab Provider. When calling, have the model number, serial number, nature of the problem, and the error code if available.
  • Page 45 ...
  • Page 46 ...
  • Page 47 Quick Reference Information Quantum Rehab Provider: Address: Phone Number: Purchase Date:...
  • Page 48 401 York Avenue Duryea, PA 18642 Canada 5096 South Service Road Beamsville, Ontario L0R 1B3 32 Wedgwood Road Bicester, Oxfordshire OX26 4UL Australia 20-24 Apollo Drive Hallam, Victoria 3803 Italy Via del Progresso, ang. Via del Lavoro Loc. Prato della Corte 00065 Fiano Romano (RM) B.V.

Table of Contents