Sony HCD-CZ1 Service Manual page 24

HCD-CZ1/NAS-CZ1
QQ
3 7 63 1515 0
Error detail:
Digit Contents
1st Error number
2nd and 3rd Kind of error
4th and 5th Process when an
error occurred
Step number
6th and 7th when an error
occurred
Disc speed
TE
L 13942296513
8th and 9th
when an error
occurred
10th an 11th Not used
CD SERVICE MODE
1. Press the button to turn the power on.
I/1
2. Press the [FUNCTION] button to select "CD".
3. Press three buttons of [VOL +],
4. If this mode is activated, "SERVICE MODE" is displayed on
the fluorescent indicator tube. (Goes off that display when
release three buttons)
5. In this mode, it operation as following table.
Buttons Display
* 1 SLED OUT
.
* 1 SLED IN
>
LD ON or LD OF
N
*1) Use the remote commander (RM-ANP002)
6. To release this mode, press the
off.
www
.
24
http://www.xiaoyu163.com
Value Detail
0 to 9 "0" is latest error
01 Focus error
02 GFS error
03 Time out of wake up
04 Defocused continuously
05 Q code error
06 Can not tracking on
07 Blank disc
01 Shipping
02 Power off in progress
03 Power on in progress
04 Initializing
05 Oscillation stop status
06 Starting up the oscillation
07 Stop status
08 Stopping in progress
09 Starting up in progress
0a TOC reading
0b Searching
0c Playback in progress
0d Pause in progress
0e Playback manual searching
0f Pause manual searching
XX Step number
01 Normal speed
02 Double speed
04 4 times speed
00 Fixed at "00"
and [1] simultaneously.
N
Operation
Move the sled to outer side
Move the sled to inner side
Laser diode on / off
button to turn the power
I/1
x ao
y
i
http://www.xiaoyu163.com
8
CD SERVO TEST MODE
1. Press the button to turn the power on.
I/1
2. Press the [FUNCTION] button to select "CD"
3. Press three buttons of
4. In this mode, it the display changes as follows (Servo test
menu mode) by pressing the
commander (RM-ANP002).
5. To release this mode, press the
off.
Servo test menu:
r
bdt S CURVE
r
bdt RAM READ
r
bdt RAM WRITE
r
bdt COMOUT
r
bdt ERR RATE
1. bdt S CURVE mode
* This mode is use the S-curve check.
1. In the servo test menu mode, press the
remote commander (RM-ANP002) to select "<bdt S
Q Q
3 6 7 1 3
CURVE>".
2. Press the [ENTER] key to enter the S-curve mode.
3. To back to the servo test menu mode, press the
remote commander (RM-ANP002)
2. bdt RAM READ made
1. In the servo test menu mode, press the
remote commander (RM-ANP002) to select "<bdt RAM
READ>".
2. Press the [ENTER] key to enter the RAM read mode.
3. In this mode, the display cyclic changes as follow by pressing
the [ALBUM -] or [ALBUM+] key.
Display
DISC SIZE 00:no disc, 01:8cm disc,02:12cm disc
RFDoffset RFDC offset value
RFAoffset RFAC offset value
FE offset FE offset value
TE offset TE offset value
RF gain_2 RF AMP secondly gain value
TE gain_2 TE secondly gain value
EFBALgain EF balance gain value
EQ BOOT EQ boot setting value
4. To back to the servo test menu mode, press the
remote commander (RM-ANP002)
u163
.
2 9 9 4 2 8
, and 2 simultaneously.
VOL + N
or keys on remote
. >
button to turn the power
I/1
or
. >
1 5 0 5 8 2 9 9 4
or
. >
Item
m
co
9 9
keys on
2 8 9 9
key on
x
keys on
key on
x