Denon AVR-2313CI Service Manual page 70

3.3. About the error code
See the table below for error codes and details of faults when the firmware is updated through USB memory.
Error
Details of Error code
Code
01 Unable to detect USB.
02 No FirmwareFile in USB.
FirmwareFile in USB for unsupported
03
Model name/area
Failed to obtain entire Firmware
04
information.
TimeOut while obtaining entire
05
Firmware information
Failed to obtain individual Firmware
06
information.
TimeOut while obtaining individual
07
Firmware information
Error notification received while
08
requesting FirmwareInfo.
TimeOut while obtaining Firmware
09
information
Unable to detect USB for
0A
FirmwareDownload.
No FirmwareFile for
0B
FirmwareDownload.
Received value with invalid
0C
PackageVersion.
No UpdatePacket received from
10
DM860A (TimeOut).
Abnormal data in UpdatePacket
11
received from DM860A (FormatError).
Abnormal data in UpdatePacket
12 received from DM860A
(CheckSumError).
BlockErase failed before rewriting
13
Main.
14 BlockWrite failed while rewriting Main.
Error in Verify after rewriting Main
15
(CheckSumError).
20 Unable to detect USB after SBLMode.
Display
C o n n e c t i o n F a i l 0 1
F i l e s N o t F o u n d
N o t M a t c h F i r m
C o n n e c t i o n F a i l 0 4
C o n n e c t i o n F a i l 0 5
C o n n e c t i o n F a i l 0 6
C o n n e c t i o n F a i l 0 7
C o n n e c t i o n F a i l 0 8
C o n n e c t i o n F a i l 0 9
C o n n e c t i o n F a i l 0 A
F i l e s N o t F o u n d
C o n n e c t i o n F a i l 0 C
U p d a t i n g
U p d a t i n g
U p d a t i n g
E r a s e f a i l
U p d a t i n g
U p d a t e C h e c k N G
C o n n e c t i o n F a i l 2 0
70
Disconnect and connect the USB
memory.
Make sure that the FirmwareFile is in
0 2
the USB memory.
Check the supported Model name/area
0 3
for the FirmwareFile.
Start the USB Update again.
Start the USB Update again.
Start the USB Update again.
Start the USB Update again.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the "Power
operation ( X )" button for five seconds.
Disconnect and connect the USB
memory.
Disconnect and connect the USB
0 B
memory.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
f a i l 1 0
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
f a i l 1 1
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
f a i l 1 2
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
1 3
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
f a i l 1 4
display, press and hold the "Power
operation ( X )" button for five seconds.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error
1 5
display, press and hold the "Power
operation ( X )" button for five seconds.
Disconnect and connect the USB
memory.
Coping strategies