Yamaha HTR-6290 Service Manual page 31

Av receiver/av amplifier
Hide thumbs Also See for HTR-6290:
Table of Contents

Advertisement

3.
Connect the power cable of this unit to the AC outlet.
4.
Press the "MASTER ON/OFF" key of this unit while
simultaneously pressing the "STRAIGHT" key of this
unit. Then the ADVANCED SETUP mode is activated.
(Fig. 4)
"MASTER ON / OFF" key
5.
Press and hold the "INFO" key of this unit for about 3
seconds. (Fig. 4)
Writing of the firmware is started. (Fig. 4)
6.
Turn the "PROGRAM" knob to select USB.
7.
Press the "INFO" key of this unit. (Fig. 4)
Writing of the firmware is set in the wait mode.
8.
Insert the USB flash memory to the USB terminal of
this unit. (Fig. 4)
Writing of the firmware is started.
*
It takes about 10 seconds before writing is start-
ed.
Writing in wait mode. / 書き込み待機中
USB Upgrader
Dest x
9.
When writing of the firmware is completed, the power
of this unit turns OFF/ON automatically.
*
If <Firmware Update is complete!> is not dis-
played, or the error message is displayed before
writing is completed, perform the operation pro-
cedures from step 1 to 8 all over again.
10. Press the "MASTER ON/OFF" key of this unit to turn
off the power.
11. Disconnect the power cable of this unit from the AC
outlet.
"PROGRAM" knob
"STRAIGHT" key
Fig. 4
Writing being executed. / 書き込み中
Updating...
Step x/x : yy%
Fig. 5
RX-V1900/HTR-6290/DSP-AX1900
3.
本機の電源コードを AC コンセントに接続します。
4.
本 機 の STRAIGHT キ ー を 押 し な が ら、 MASTER
ON/OFF キーを押し、アドバンスドセットアップを
起動します。 (Fig. 4)
USB terminal
ADVANCED SETUP mode
SPEAKER IMP.
Writing of the firmware mode
Firm Update
"INFO" key
SelectCDDA/USB
5.
本機の INFO キーを約 3 秒間押し続けます。 (Fig. 4)
ファームウェアの書き込みが起動します。 (Fig. 4)
6.
PROGRAM ツマミを回して、USB を選択します。
7.
本機の INFO キーを押します。 (Fig. 4)
ファームウェアの書き込み待機中になります。
8.
本機の USB 端子に USB フラッシュメモリーを差し込
みます。 (Fig. 4)
ファームウェアの書き込みが開始されます。
※ 書き込みが開始されるまで約 10 秒間かかります。
Writing is completed. / 書き込み完了
FirmwareUpdate
is complete!
9.
ファームウェアの書き込みが完了すると、自動で本
機の電源がオフ/オンします。
※ < Firmware Update is complete! >が表示されな
い場合、または途中でエラーが表示された場合は、
操作手順の 1 から 8 までをもう一度やり直してく
ださい。
10. 本機の MASTER ON/OFF キーを押し、電源オフし
ます。
11. 本機の電源コードを AC コンセントから抜きます。
8
MIN
31

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Rx-v1900Dsp-ax1900

Table of Contents