Circuit Boards Location - Sony HCD-GNZ55D Service Manual

HCD-GNZ55D
Q Q
3 7 6 3 1 5 1 5 0

6-6. CIRCUIT BOARDS LOCATION

SW board
DMB15 board
MOTOR (LD) board
VIDEO board
POWER UNIT
IR board
PANEL board
VOLUME board
MIC board
T E
L 1 3 9 4 2 2 9 6 5 1 3
w w w
HCD-GNZ55D
SENSOR board
DRIVER board
MOTOR (TB) board
MAIN board
SPEAKER board
S-MASTER board
ADC board
x a o
y
. i
http://www.xiaoyu163.com
8
• Note For Printed Wiring Boards And Schematic Diagrams
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layer's patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Component Side) the parts face are indicated.
• Indication of transistor.
C
Q
These are omitted.
B E
Q
B C E
These are omitted.
Q
B C E
These are omitted.
Q Q
3 7 6 3
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
u 1 6 3
.
32 32
http://www.xiaoyu163.com
2 4
9 9 8
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /
specified.
• 2 : nonflammable resistor.
• C : panel designation.
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• B : B– Line.
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : AUDIO
f : TUNER
L : VIDEO (COMPONENT)
g : VIDEO (COMPOSITE)
E
: TAPE PLAY (DECK A)
d
: TAPE PLAY (DECK B)
G
1 5 1 5 0 8 : TAPE REC (DECK B) 9 2 4
J
: DVD (AUDIO)
c : DVD (RF)
I : DVD (DIGITAL)
• Abbreviation
E3 : 240 V AC area in E model
E12 : 220-240 V AC area in E model
E13 : 220-230 V AC area in E model
E15 : Iran model
EA : Saudi arabia model
MY : Malaysia model
PH : Philippine model
SP : Singapore model
TH : Thai model
m
c o
2
9 9
W or less unless otherwise
4
9 8 2 9 9