Vertex Standard VXR-9000E Operating Manual page 6

Programmable Function ( PF ) Key Details
t t D
Wo one ec
Press (or Press and hold in for one second) the PF
key assigned to "Two Tone Dec" to turn the 2-Tone
Decoder "On" or "Off" (toggle).
cW iD S
ingle
Press (or Press and hold in for one second) the PF
key assigned to "CW ID Single" to send the station
callsign, via Morse Code, once. Programming of the
callsign is performed by your Vertex Standard deal-
er.
cW M 1 - cW M
eSSage
Press (or press and hold in for one second) the PF
key assigned to "CW Message 1 - 8" to send a pre-
programmed Morse Code message on the transmit-
ted signal. Programming of the message(s) is per-
formed by your Vertex Standard dealer.
Dc p S
oWeR ave
Press (or Press and hold in for one second) the PF
key assigned to "DC Power Save" to turn the DC
Power Save feature "On" or "Off" (toggle).
When DC Power Save feature is set to "ON," activate
the various power save feature (determined from
your Vertex Standard dealer) while the repeater op-
erates from the Backup Power Source.
e
ncRyption
Press (or Press and hold in for one second) the PF
key assigned to "Encryption" to turn off the Option-
al Encryption Unit temporarily.
e c
ncRyption oDe
Press (or Press and hold in for one second) the PF
key assigned to "Encryption Code" to select the
Encryption Code (determined from your Vertex
Standard dealer; require the FVP-35 Rolling Code
Encryption Unit).
k l
ey ock
Press (or Press and hold in for one second) the PF
key assigned to "Key Lock" to lock the repeater's
front panel keys (except "Key Lock" key); this fea-
ture can be enabled to prevent repeater settings from
being disturbed.
l ptt
ocal
Press (or Press and hold in for one second) the PF
key assigned to "Local PTT" to enable ("On") or dis-
able ("Off") operation using a PTT switch connected
to the front panel's Microphone Jack.
4
8
eSSage
VXR-9000E FM R
M
onitoR
Press (or Press and hold in for one second) the PF
key assigned to "Monitor " to cancel CTCSS and
DCS squelch decoding, so as to enable reception of
signals present on the channel that do not contain a
matching CTCSS tone or DCS code.
M M
onitoR
This function provides to "Monitor" to cancel CTC-
SS and DCS squelch decoding, so long as the PF key
assigned to "Monitor M" is pressed and held in.
M t
ulti one
Press (or Press and hold in for one second) the PF
key assigned to "Multi Tone" to switch the Tone
Table between "Main" and "Sub."
p i
anel nDicatoR
Press (or Press and hold in for one second) the PF
key assigned to "Panel Indicator" to turn the Front
Panel's Illumination "On" or "Off" (toggle).
R
eMote
Press (or Press and hold in for one second) the PF
key assigned to "Remote" to toggle the operating
mode between the "Remote" mode and "Local"
mode.
When the "Remote" mode is selected, the repeater
operates according to the control instructions re-
ceived from the external device (connected to the
ACC jack on the rear panel). While in the "Local"
mode, the repeater operates from the front panel's
PF keys.
R
epeat
Press (or Press and hold in for one second) the PF
key assigned to "Repeat" to toggle the operating
mode between the "Repeater" mode and "Base
Transceiver" mode.
For normal operation, set this key to the "Repeat"
mode. When the "Base Transceiver" mode is se-
lected, you can speak into the microphone to use this
repeater as a transceiver.
R
eSet
Press (or Press and hold in for one second) the PF
key assigned to "Reset" to reset (same function as
the POWER switch "off" and "on") the repeater.
EpEatER
O M
pERating anual