Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Monoprice MONOLITH 7
Summary of Contents for Monoprice MONOLITH 7
- Page 1 MONOLITH 7 MULTI-CHANNEL POWER AMPLIFIER 14566 User’s Manual...
-
Page 2: Table Of Contents
CONTENTS SAFETY WARNINGS AND GUIDELINES ............................3 INTRODUCTION ........................................ 4 FEATURES ..........................................4 CUSTOMER SERVICE ....................................5 PACKAGE CONTENTS ....................................5 PRODUCT OVERVIEW ....................................6 CABLE PREPARATION ....................................7 Speaker Wires ......................................7 RCA Cables ........................................8 Trigger Cables ......................................8 REMOTE POWER ON.................................... -
Page 3: Safety Warnings And Guidelines
SAFETY WARNINGS AND GUIDELINES This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately unplug it from the power outlet and allow it to fully dry before reapplying power. -
Page 4: Introduction
INTRODUCTION Thank you for purchasing this Monolith 7-Channel 200-Watt Power Amplifier! This power amplifier features seven independent channels, each capable of delivering more than 200 watts of power into 8 ohm loads. A trigger input jack allows for remote power on/power off when a source device is powered on. -
Page 5: Customer Service
If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-... -
Page 6: Product Overview
PRODUCT OVERVIEW A. INPUT 1-7: RCA line-level inputs for connection to the preamplifier outputs on a dedicated preamplifier or AV receiver. B. TRIGGER INPUT: 3.5mm TS jack for connection to the trigger output of a source device. The presence of voltage on this input will cause the amplifier to power on. The amplifier will automatically power down into standby mode after the trigger signal has been removed. -
Page 7: Cable Preparation
F. GND: Chassis ground. While a grounding wire is rarely needed, occasionally there is a hum issue when components are interconnected. This can be remedied by tying their chassis grounds together. POWER SWITCH (Front Panel, not pictured): Switches the amplifier between standby mode and full power on. -
Page 8: Rca Cables
The identified conductor is usually used for the positive (+/red) connection and the other for the negative (-/black) side. Note: When cutting speaker wire, ensure that the length of each stereo pair is the same. This ensures that the overall impedance of each paired channel is identical. If there is any excess speaker wire, it should not be coiled, as it could create an antenna to receive stray radio signals. -
Page 9: Installation
To use the amplifier with remote power on, the Master Power switch on the rear panel should be in the ON position and the Power switch on the front panel in the Standby position. To override the remote power on feature or to use the amp without it, simply use the Power switch on the front panel to turn the amp on and off (standby). -
Page 10: Peak Indicator
Warning! Do not plug the amplifier into a switched outlet on a preamplifier or other audio component. The amplifier should be plugged directly into an AC wall outlet. 10. Ensure that the volume on the preamplifier is set to the minimum level. 11. -
Page 11: Protection Circuitry
PROTECTION CIRCUITRY If the amplifier senses a short on one of the speaker wires the built-in protection circuit will cut off audio output. The circuit will continue to monitor the line and will stay cut off as long as the short continues to exist. If this occurs, inspect the speaker wire connections at each end and fix any shorts that exist. -
Page 12: Technical Support
TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. - Page 13 Total Harmonic Distortion (THD) Less than 0.03% at full rated FTC power Less than 0.005% at full EIA power at 1kHz Intermodulation Distortion (IMD) Less than 0.03% at full rated FTC power Less than 0.005% at full EIA power at 1kHz Load Impedance Safe with all types of loads Rated for 4 to 16 ohms...
-
Page 14: Regulatory Compliance
REGULATORY COMPLIANCE Notice for FCC This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifying the equipment without authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices.
Need help?
Do you have a question about the MONOLITH 7 and is the answer not in the manual?
Questions and answers