Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Monoprice Monolith 11X
Summary of Contents for Monoprice Monolith 11X
- Page 1 Monolith™ 11X Multi-Channel Power Amplifier Model 33307 User's Manual...
-
Page 2: Table Of Contents
CONTENTS SAFETY WARNINGS AND GUIDELINES ............................3 INTRODUCTION ........................................ 4 FEATURES ..........................................4 CUSTOMER SERVICE ....................................5 PACKAGE CONTENTS ....................................5 PRODUCT OVERVIEW ....................................6 CABLE PREPARATION ....................................7 Speaker Wires ......................................7 RCA or XLR Cables ....................................8 Trigger Cables ......................................8 REMOTE POWER ON.................................... -
Page 3: Safety Warnings And Guidelines
SAFETY WARNINGS AND GUIDELINES This device is intended for indoor use only. Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately unplug it from the power outlet and allow it to fully dry before reapplying power. -
Page 4: Introduction
Do not plug this device into the switched output of a preamplifier or other audio component. This amplifier requires higher current levels than these devices are designed to handle. Unplug this device from the power source when not in use. ... -
Page 5: Customer Service
If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-... -
Page 6: Product Overview
PRODUCT OVERVIEW INPUTS: XLR and RCA line-level inputs for connection to the preamplifier outputs on a dedicated preamplifier or AV receiver. The XLR/RCA switches switch between the XLR and RCA inputs. You can use a mix of XLR and RCA inputs. OUTPUTS: Paired 5-way binding posts for connecting the speakers. -
Page 7: Cable Preparation
CABLE PREPARATION You will need several cables for this installation. None of the cables or connectors mentioned in this section are included with the system. Important Safety Note! If you plan on running any of these cables through the walls, through a connecting floor, or inside an air duct, they should be rated for In-Wall, Riser (between floors), or Plenum (air duct) use in commercial installations. -
Page 8: Rca Or Xlr Cables
RCA or XLR Cables You will need RCA or XLR cables to connect the preamp outputs on your preamplifier to the inputs on this amplifier. In most cases, ordinary RCA cables are sufficient. However, if there is a significant distance between the amplifier and the preamplifier, it is recommended to use RCA cables manufactured using shielded RG6 or RG59 cable. -
Page 9: Installation
INSTALLATION Perform the following steps to install this amplifier into an audio system. 1. Power off and unplug all equipment that will be connected to this amplifier. 2. Prepare lengths of speaker wire (not included) to connect each of the output channels to its respective speaker. -
Page 10: Main Circuit Breaker
12. Power on all equipment connected to the amplifier, then flip the Circuit Breaker on the amp to the ON position. The power button LED will blink until the circuitry is properly warmed up. Once the LED stops blinking and illuminates steadily, the amplifier has finished the start-up process and is ready for operation. -
Page 11: Troubleshooting
TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. -
Page 12: Specifications
SPECIFICATIONS Model 33307 Total Number of Channels EIA 1kHz Output Power at 8 Ohms* 250 watts (3 channels) EIA 1kHz Output Power at 4 Ohms* 375 watts (3 channels) FTC Full Bandwidth Output Power 200 watts (3 channels) or 100 watts (8 channels) at 8 Ohms** FTC Full Bandwidth Output Power 300 watts (3 channels) -
Page 13: Regulatory Compliance
Modifying the equipment without Monoprice's authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to... -
Page 14: Notice For Industry Canada
Consult the dealer or an experienced radio/TV technician for help. Notice for Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Monolith™ and the Monolith logo are trademarks of Monoprice Inc.
Need help?
Do you have a question about the Monolith 11X and is the answer not in the manual?
Questions and answers