Monoprice Monolith 7X User Manual

Monoprice Monolith 7X User Manual

7-channel 200-watt power amplifier

Advertisement

Quick Links

Monolith 7X 7-Channel 200-Watt Power Amplifier
Model 14566
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Monolith 7X and is the answer not in the manual?

Questions and answers

Summary of Contents for Monoprice Monolith 7X

  • Page 1 Monolith 7X 7-Channel 200-Watt Power Amplifier Model 14566 User's Manual...
  • Page 2: Table Of Contents

    CONTENTS SAFETY WARNINGS AND GUIDELINES ............................3 INTRODUCTION ........................................ 4 FEATURES ..........................................4 CUSTOMER SERVICE ....................................5 PACKAGE CONTENTS ....................................5 PRODUCT OVERVIEW ....................................6 CABLE PREPARATION ....................................7 Speaker Wires ......................................7 RCA Cables ........................................8 Trigger Cables ......................................8 REMOTE POWER ON....................................
  • Page 3: Safety Warnings And Guidelines

    SAFETY WARNINGS AND GUIDELINES  This device is intended for indoor use only.  Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device. If moisture does get in or on the device, immediately unplug it from the power outlet and allow it to fully dry before reapplying power.
  • Page 4: Introduction

     Do not plug this device into the switched output of a preamplifier or other audio component. This amplifier requires higher current levels than these devices are designed to handle.  Unplug this device from the power source when not in use. ...
  • Page 5: Customer Service

    If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-...
  • Page 6: Product Overview

    PRODUCT OVERVIEW A. INPUT 1-7: RCA and XLR line-level inputs for connection to the preamplifier outputs on a dedicated preamplifier or AV receiver. The Input Select switch switches between the RCA and XLR inputs. B. TRIGGER INPUT: 3.5mm TS jack for connection to the trigger output of a source device.
  • Page 7: Cable Preparation

    CABLE PREPARATION You will need several cables for this installation. None of the cables or connectors mentioned in this section are included with the system. Important Safety Note! If you plan on running any of these cables through the walls, through a connecting floor, or inside an air duct, they should be rated for In-Wall, Riser (between floors), or Plenum (air duct) use in commercial installations.
  • Page 8: Rca Cables

    RCA or XLR Cables You will need seven single RCA or XLR cables to connect the preamp outputs on your preamplifier to the inputs on this amplifier. In most cases, ordinary RCA cables are sufficient. However, if there is a significant distance between the amplifier and the preamplifier, it is recommended to use RCA cables manufactured using shielded RG6 or RG59 cable.
  • Page 9: Installation

    INSTALLATION Perform the following steps to install this amplifier into a 7.1-channel audio system. 1. Power off and unplug all equipment that will be connected to this amplifier. 2. Prepare seven lengths of speaker wire (not included) to connect each of the seven output channels to its respective speaker.
  • Page 10: Main Circuit Breaker

    circuitry is properly warmed up. Once the LED stops blinking and illuminates steadily, the amplifier has finished the start-up process and is ready for operation. Note: It is recommended to always turn the amplifier on last and to turn it off first whenever powering your audio system on or off.
  • Page 11: Troubleshooting

    TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates.
  • Page 12: Specifications

    SPECIFICATIONS Model 14566 Number of Channels EIA 1kHz Output Power at 8 Ohms* 250 watts EIA 1kHz Output Power at 4 Ohms* 375 watts FTC Full Bandwidth Output Power 200 watts at 8 Ohms** FTC Full Bandwidth Output Power 300 watts at 4 Ohms** RCA Input: 1.49 Volts Input Sensitivity for Full Rated Power...
  • Page 13 Input Impedance 28 kilohms (nominal) Remote Trigger Voltage 3.3 ~ 24 VDC at 5mA or greater DC Output Offset Less than ±5mV Input Power 120 VAC (nominal) Chassis Dimensions 17.0" x 7.0" x 16.5" (432 x 178 x 419 mm) Net Weight 93.2 lbs.

This manual is also suitable for:

14566

Table of Contents