Maintenance; Optional Accessories - Makita DDF343 Instruction Manual

Screwdriving operation
009082
CAUTION:
Adjust the adjusting ring to the proper torque level
•
for your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
CAUTION:
Make sure that the driver bit is inserted straight in the
•
screw head, or the screw and/or bit may be damaged.
NOTE:
When driving wood screws, predrill pilot holes to
•
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
3.1 (1/8")
3.5 (9/64")
3.8 (5/32")
4.5 (11/64")
4.8 (3/16")
5.1 (13/64")
5.5 (7/32")
5.8 (7/32")
6.1 (15/64")
001904
Drilling operation
First, turn the adjusting ring so that the pointer points to
the marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer at
the point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled dry.
Recommended size of pilot hole
(mm)
2.0 - 2.2 (5/64" - 3/32")
2.2 - 2.5 (3/32" - 3/32")
2.5 - 2.8 (3/32" - 7/64")
2.9 - 3.2 (7/64" - 1/8")
3.1 - 3.4 (1/8" - 9/64")
3.3 - 3.6 (1/8" - 9/64")
3.7 - 3.9 (9/64" - 5/32")
4.0 - 4.2 (5/32" - 11/64")
4.2 - 4.4 (11/64" - 11/64")
CAUTION:
Pressing excessively on the tool will not speed up
•
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
There is a tremendous force exerted on the tool/bit
•
at the time of hole break through. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
A stuck bit can be removed simply by setting the
•
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
do not hold it firmly.
Always secure small workpieces in a vise or similar
•
hold-down device.
If the tool is operated continuously until the battery
•
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before attempting to
perform inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol or the
•
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
These accessories
•
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons.
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Drill bits
•
Screw bits
•
Hook
•
Various type of Makita genuine batteries and
•
chargers
7
or attachments
Only use accessory or
are