Diagrams; Circuit Boards Location; Reference Information - Sony Trinitron CPD-G220R Service Manual

4-1. CIRCUIT BOARDS LOCATION

U Board
4-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS INFORMATION
All capacitors are in µF unless otherwise noted. pF : µµF 50WV or less
are not indicated except for electrolytics and tantalums.
All electrolytics are in 50V unless otherwise specifi ed.
All resistors are in ohms. KΩ=1000Ω, MΩ=1000kΩ
Indication of resistance, which does not have one for rating electrical
power, is as follows: Pitch : 5mm
Rating electrical power :
/ W in resistance, / W and
1 1 1
4 10
: nonfl ammable resistor.
: fusible resistor.
: internal component.
: panel designation and adjustment for repair.
All variable and adjustable resistors have characteristic curve B, unless
otherwise noted.
Readings are taken with a color-bar signal input.
Readings are taken with a 10MΩ digital multimeter.
Voltages are DC with respect to ground unless otherwise noted.
Voltage variations may be noted due to normal production tolerances.
All voltages are in V.
S : Measurement impossibillity.
: B+line.
: B-line. (Actual measured value may be different).
: signal path. (RF)
Circled numbers are waveform references.
SECTION 4: DIAGRAMS
H1 Board D Board
1 / W
4
/ W in chip resistance.
8
The components identifi ed by shading and
only with part number specifi ed.
The symbol
side of the board. Replace only with fuse of the same rating as marked.
A Board
Les composants identifi es per un trame et une marque
securite. Ne les remplacer que par une piece portant le numero specifi e.
Le symbole
fusible de meme yaleur, comme maque.
The components identifi ed by X in this basic schematic diagram
have been carefully factory-selected for each set in order to
satisfy regulations regarding X-ray radiation. Should replacement be
necessary, replace only with the value originally used.
When replacing components identifi ed by Y, make the necessary
adjustments as indicated. If the results do not meet the specifi ed value,
change the component identifi ed by X and repeat the adjustment until
the specifi ed value is achieved.
When replacing the parts listed in the table below, it is important to
perform the related adjustments.
HV ADJ
HV Regulator
Circuit
HV HOLD
DOWN Circuit
Beam Current
Protector Circuit

REFERENCE INFORMATION

RESISTOR
: RN METAL FILM
: RC SOLID
: FPRD NONFLAMMABLE CARBON
: FUSE NONFLAMMABLE FUSIBLE
: RW NONFLAMMABLE WIREWOUND
: RS NONFLAMMABLE METAL OXIDE
: RB NONFLAMMABLE CEMENT
: ADJUSTMENT RESISTOR
COIL
: LF-8L MICRO INDUCTOR
— 12 —
symbol are critical for safety. Replace
!
indicates a fast operating fuse and is displayed on the component
indique une fusible a action rapide. Doit etre remplace par une
Part Replaced (
RV501
Part Replaced (
D board T501, IC501, RV501, R540,
R541, R542, R544, R564, R567,
R568, C532, C534, C539, C553,
C554, C555, C556, C558, C561
D board T501, R510, R543, R547, R549,
R552, R595, D515, D517, C540,
C542, C544, IC607, IC901, C951
D board T501, R545, R546, R548, R550,
R596, R934, C535, C541, IC605,
IC607, IC901
CAPACITOR
: TA TANTALUM
: PS STYROL
: PP POLYPROPYLENE
: PT MYLAR
: MPS METALIZED POLYESTER
: MPP METALIZED POLYPROPYLENE
: ALB BIPOLAR
: ALT HIGH TEMPERATURE
: ALR HIGH RIPPLE
CPD-G220R/G220S
sont critiques pour la
!
)
)