Simple Setup; Step1 Locating; Step2 Connecting The Speakers And Voltage Selection; Positioning - Panasonic SC-PM39D Operating Instructions Manual

Simple setup

STEP
Speaker
(SB-PM39)
Place the speakers so that the tweeter is on the inside.
Caution
•
Use the speakers only with the recommended
system. Failure to do so may lead to damage to the
amplifier and/or the speakers, and may result in the
risk of fire. Consult a qualified service person if
damage has occurred or if you experience a sudden
change in performance.
•
Do not attach these speakers to walls or ceilings.
STEP
Twist the vinyl tip and pull off.
Right speaker
RQT7502
6
1
Locating
Tweeter
Main unit Speaker
(SA-PM39D) (SB-PM39)
2
Connecting the speakers and voltage selection
Confirm the colors of the tags
on the ends of the cords.
White
Connect cords so tag colors
match the terminal colors.
Red
White
Black
Blue
Connect the left (L) side in
the same way.
Copper(White tag)
Silver(Black tag)
Silver(Blue tag)
Copper(Red tag)
•
Use only supplied speakers
Using other speakers can damage the unit and sound quality will be
negatively affected.
•
Set the speakers up on an even surface to prevent them from
falling. Take proper precautions to prevent the speakers from falling
if you cannot set them up on an even surface.
Positioning for best effect
How you set up your speakers can affect the bass and the sound
field. Note the following points.
•
Place speakers on flat secure bases.
•
Placing speakers too close to floors, walls, and corners can result in
excessive bass. Cover walls and windows with a thick curtain.
•
Keep your speakers at least 10 mm away from the system for
proper ventilation.
•
To avoid damage to the speakers, do not touch the speaker cones if
you have taken the nets off.
Notes on speaker use
•
You can damage your speakers and shorten their useful life if you
play sound at high levels over extended periods.
•
Reduce the volume in the following cases to avoid damage.
– When playing distorted sound.
– When the speakers emit strange noise (howling) from a
microphone or record player, noise from FM broadcasts, or
continuous signals from an oscillator, test disc, or electronic
instrument.
– When adjusting the sound quality.
– When turning the unit on or off.
If irregular coloring occurs on your television
These speakers are designed to be used close to a television, but
the picture may be affected with some televisions and set-up
combinations.
If this occurs, turn the television off for about 30 minutes.
The television's demagnetizing function should correct the problem.
If it persists, move the speakers further away from the television.
Note
•
Never short-circuit positive (+) and negative (–) speaker
wires.
•
Be sure to connect only positive (copper) wires to
positive (+) terminals and negative (silver) wires to
Blue Black Red
negative (–) terminals.
Incorrect connection can damage the speakers.
AM ANT FM ANT
EXT LOOP 75Ω
L SUBWOOFER
R
OUT
AUX
L
OPTICAL
OUT
R
HIGH(6Ω) LOW(6Ω)
SPEAKERS (SB-PM39)
HAUT-PARLEURS
S-VIDEO
OUT
VIDEO
OUT
VOLT ADJ
COMPONENT VIDEO OUT
P P Y
R B
For Saudi Arabia, Kuwait, the Middle East
and Southeast Asia only
Before connecting the AC power
supply cord, set the voltage.
Voltage Selector
Use a flat-head screwdriver to turn the
voltage selector on the rear panel to the
appropriate position for the area in which
this system is used.
AC IN
If the power supply in your area is 115 V
or 120 V, please set the voltage selector
as follows:
•
For 115 V: Set to 110 V.
•
For 120 V: Set to 127 V.
VOLT ADJ
220
I V
230
127 V 110 V 220-230 V 240 V