Table of Contents
Advertisement
12
! If an update file is provided on the Pioneer website, download it onto your computer. When downloading an
update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before
saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models
on the USB memory device, delete them.
http://www.pioneer.eu/eur (for Europe)
http://www.pioneer.com.au (for Australia and New Zealand)
! If an update file does not exist in the Pioneer's website, updating the software for the receiver is not necessary.
Important
! DO NOT unplug the power cord during updating.
! When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device,
do not disconnect the USB memory device.
! If updating is interrupted before it is completed, start updating over from the beginning.
! The receiver's settings may be reset when the software is updated. Information on the models for which the
settings are reset is provided on the Pioneer website. Check the website before updating.
1
Select 'Software Update' from the Other Setup menu.
2
Select the update procedure.
! Update via Internet – The receiver checks whether updatable software is available via the Internet.
! Update via USB Memory – The receiver checks whether the USB memory device inserted into the USB port
on the receiver's front panel contains updatable software.
"Accessing" is displayed and the update file is checked. Wait a while.
3
Check on the screen whether or not an update file was found.
If "New version found." is displayed, the update file has been found. The version number and updating time are
displayed.
If "This is the latest version. There is no need to update." is displayed, no update file has been found.
4
To update, select OK.
The updating screen appears and updating is performed.
! The power turns off automatically once updating is completed.
Software Update messages
Status messages
Descriptions
Try disconnecting then reconnecting the USB device or storing the update file again. If the error still
occurs, try using a different USB memory device.
FILE ERROR
No update file was found on the USB memory device. Store the file in the USB memory device's root
directory.
UPDATE ERROR 1 to
Turn the receiver's power off, then turn it back on and try updating the software again.
UPDATE ERROR 7
If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a
Update via USB
USB memory device and connect the device to the USB port. When the file is found, software updating
starts automatically.
UE11
UE22
Updating has failed. Use the same procedure to update the software again.
UE33
ZONE Setup
Switches the sub-zone setting.
MAIN/HDZONE setting (setting for how to use the HDMI OUT 3 terminal)
1
Select 'ZONE Setup' from the Other Setup menu.
2
Select 'MAIN/HDZONE', then press ENTER.
3
Set how the HDMI OUT 3 terminal is to be used.
! MAIN: Select this to output the same input source as in the main zone.
After setting this to MAIN, exit the home menu, then press OUT P. and select the terminal for HDMI output
(page 83
).
! HDZONE (default): Use the HDMI output's multizone function (HDZONE) to output an input source different
from the one in the main zone
(page 84
).
4
Select 'OK', then press ENTER.
ZONE 2/ZONE 3/HDZONE setting
The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted
here.
! When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and
performing playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the
receiver or to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment
from the factory, allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from
the connected amplifier, make the setting below.
! HDZONE can be set when Speaker System is 7.2ch + HDZONE, 5.2 Bi-Amp+HDZONE or
5.2 +ZONE 2+HDZONE.
! HDZONE is set to Variable. It cannot be set to –40 dB Fixed and 0 dB Fixed.
CAUTION
! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals
is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may
be produced even when Volume Level is set to –40 dB Fixed.
1
Select 'ZONE Setup' from the Other Setup menu.
2
Select a sub zone for which you wish to change the setting.
3
Select the Volume Level setting you want.
! Variable (default) – Adjusts the sound volume of the sub zone using this unit.
! –40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set
here.
4
Select the Power ON Level setting you want.
Sets the sound volume of the sub zone when the multi-zone function is used to turn on the sub zone. Volume can
be set for ZONE 2, ZONE 3, and HDZONE, respectively.
When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot
be set here.
! LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were
listening to that zone.
! "---" – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.
! –80.0dB to 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be
set up to the value set at Volume Limit below.
108
The System Setup and Other Setup menus
Advertisement
Table of Contents
