Download Print this page

Toshiba SD-R1002 Installation Instructions Manual

Cd-rw/dvd-rom drive.
Hide thumbs

Advertisement

TOSHIBA
Storage Device Divsion
CD-RW/DVD-ROM
DRIVE
SD-R1002
Installation Instructions
®
with Adaptec
Easy CD Creator
TM
and
CyberLink PowerDVD
Software
TM
VERSION 3.0
DECEMBER 2000

Advertisement

   Also See for Toshiba SD-R1002

   Related Manuals for Toshiba SD-R1002

   Summary of Contents for Toshiba SD-R1002

  • Page 1

    TOSHIBA Storage Device Divsion CD-RW/DVD-ROM DRIVE SD-R1002 Installation Instructions ® with Adaptec Easy CD Creator CyberLink PowerDVD Software VERSION 3.0 DECEMBER 2000...

  • Page 2

    2. DO NOT disassemble or modify this equipment. Toshiba shall not make any guarantee to the reliability, safety and performance of this equipment expressly provided in the specification and nor be liable for any damages resulting from such unauthorized disassembly or modification.

  • Page 3: System Requirements

    Windows 95 or higher Amplified stereo speakers ™ * These requirements are only required if you are using the CyberLink PowerDVD software. The SD-R1002 CD-RW/DVD-ROM will work as a CD-ROM and CD- RW when using a lower speed Pentium system.

  • Page 4

    The following steps must be performed to properly install your CD-RW/DVD- ROM. Set drive’s jumpers Connect audio cable Attach IDE BUS cable Connect power cable Mount CD-RW/DVD-ROM ™ Install CyberLink PowerDVD software (used for viewing DVD movies) ® ™ Install Adaptec Easy CD Creator software (used for recording CDs) SETTING JUMPERS...

  • Page 5

    2. If the CD-RW/DVD-ROM is replacing a CD-ROM, disconnect all connectors and remove the CD-ROM presently installed in your system. 3. Your Toshiba CD-RW/DVD-ROM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) 4.

  • Page 6

    Connect secondary IDE BUS cable to CD-RW/DVD-ROM drive, assuring that pin 1 of the cable (side with red stripe) is connected to pin 1 on the drive. • If the CD-RW/DVD-ROM is the only drive connected on the secondary IDE BUS cable: connect drive to the last set of pins on IDE BUS cable.

  • Page 7

    ATAPI CD/DVD Software Driver: Toshiba’s CD-RW/DVD-ROM drives do not require any unique device drivers for Windows '95/'98/2000/NT. After installing your drive and re-booting, your sys- tem should recognize your drive. Win '95/'98/2000/NT operating systems support all Toshiba ATAPI CD-RW, CD-ROM and DVD-ROM drives natively.

  • Page 8

    Busy Light Volume Control Eject Button Loading Tray Emergency Eject Hole CD-RW/DVD-ROM BACK PANEL The photo below illustrates the following features of the SD-R1002 and CD-RW/ DVD-ROMs back panel: Digital Audio Out Connector ATAPI Connector Analog Audio Out Connector Power Connector...

  • Page 9: Technical Support

    SD-R1002 SPECIFICATIONS DATA CAPACITY mode 1 mode 2 (bytes/block) 2,048 2,048 2,336 ROTATIONAL SPEED DVD: 2,800rpm CD: 5,100rpm (2 - 4.8X CAV) (10.3 - 24 CAV) DVD-R: 1,100 - 2,800rpm CD-RW: 3,400rpm (2X CLV) (6.9 - 16X CAV) CD-R, CD-RW (Write):...

  • Page 10: Warranty Information

    WARRANTY INFORMATION Toshiba America Electronic Components, Inc. (“TAEC”) warrants that all prod- ucts will, upon delivery by TAEC to the customer in new condition, be free from defects in material and workmanship for a period of twelve (12) months after delivery.

  • Page 11

    460018-c0 P/N 460018-C0...

Comments to this Manuals

Symbols: 0
Latest comments: