http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block 3 7 63 1515 0 When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B E C B B C E 2SB1370 CSA952K 2SC5342Y CSC4115BC KTA1266GR KTC3198GR S D G B C E 2SK360E 2SA1235F KRA107S 2SJ460 2SB1342 2SC2714O KRC104S 2SK2541 2SD1933 RT1N441C 2SC3052F...
Page 11
http://www.xiaoyu163.com WIRING 1 ( MAIN / FRONT ) 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 11 http://www.xiaoyu163.com...
Page 20
http://www.xiaoyu163.com IC DESCRIPTION IC, M38B57MCH - E249FP 3 7 63 1515 0 Pin No. Pin Name Description — Not connected. I-HOLD Hold input. I-TRAY SW CD tray SW AD input. I-D-SW CD door open/close AD detection input (Not used). I-KEY2 Key AD input 2.
Page 22
http://www.xiaoyu163.com IC, LC78641NE-D 3 7 63 1515 0 Pin No. Pin Name Description PDO1 Internal VCO control phase comparator output pin. (Pull down) Internal VCO control phase comparator output pin. PDO2 OFF for rough servo, ON for phase servo. (Pull down) VVSS —...
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description EFLG C1, C2 error correction monitor pin. (Not used) TEST Test input pin. (Connected to GND) Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This EMPH becomes an emphasis monitor pin under control by command.
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description Synchronization signal detection output pin. FSEQ Outputs a high level when the synchronization signal detected from the EFM signal and the internally generated synchronization signal agree. (Not used) Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes DEFECT the defect monitor pin under control by command.
Page 25
http://www.xiaoyu163.com ADJUSTMENT <TUNER / DECK / FRONT> < TUNER SECTION > < DECK SECTION > 3 7 63 1515 0 1. Clock frequency Check 1. Tape Speed Adjustment (DECK 1) Settings : • Test point : TP2 (CLK) Settings : • Test tape : TTA–100 Method : Set to AM 1710kHz and check that the test point is •...
http://www.xiaoyu163.com GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units.