Disassembly - Sharp CD-C1W Service Manual

CD-C1W,CP-C1W
Caution on Disassembly
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need be
removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.
4. Take suff cient care on static electricity of integrated
circuits and other circuits when servicing.
CD-C1W
REMOVAL
STEP
1 Top Cabinet 1. Screw ....................... (A1) x4
2 Side Panel 1. Screw ....................... (B1) x6
(Left/Right) 2. Screw ...................... (B2) x4
3 CD Changer Block 1. Flat cable ................. (C1) x1
2. Screw ....................... (C2) x2
3. Screw ....................... (C3) x2
4 Tuner PWB 1. Screw ....................... (D1) x8
2. Screw ....................... (D2) x1
3. Screw ....................... (D3) x4
5 Main PWB 1. Socket ...................... (E1) x3
2. Flat Cable ................ (E2) x1
3. Flat Wire ................... (E3) x2
4. Screw ....................... (E4) x2
5. Screw ....................... (E5) x2
6 Front Panel 1. Flat Wire ................... (F1) x2
2. Screw ....................... (F2) x1
3. Screw ....................... (F3) x2
7 Display PWB 1. Knob ......................... (G1) x2
2. Nut ........................... (G2) x1
3. Screw ................... (G3) x12
8 CD Switch PWB 1. Screw ...................... (H1) x3
9 Headphones PWB 1. Screw ....................... (J1) x1
10 Tape Mechanism 1. Open the cassette holder ....
2. Screw ....................... (K1) x6
11 Power Amp. PWB 1. Socket ...................... (L1) x1
2. Screw ....................... (L2) x4
3. Screw ....................... (L3) x2
12 Power Supply 1. Screw ..................... (M1) x1
PWB 2. Screw ..................... (M2) x4
13 CD Changer Holder 1. Screw ....................... (N1) x3
14 CD Servo PWB 1. Socket ...................... (P1) x6
(Note) 2. Screw ....................... (P2) x3
15 Tray Switch PWB 1. Screw ...................... (Q1) x1
16 CD Mechanism 1. Screw ....................... (R1) x2
2. Top Bord .................. (R2) x1
3. Disc Holder .............. (R3) x1
4. Disc Tray .................. (R4) x3
5. Screw ....................... (R5) x1
6. Mechanism Holder ...............
7. Screw ....................... (R7) x2
8. Mechanism Holder ...............
9. Mechanism Holder ... (R9) x1
10. Screw ................... (R10) x4
Note : After removing the connector for the optical pickup
fromthe connector wrap the conductive aluminium foil
around the front end of connector so as to protect the
optical pickup from electrostatic damage.
PROCEDURE
Guide ....................... (R6) x1
Bracket ..................... (R8) x1

DISASSEMBLY

CP-C1W
STEP REMOVAL
1 Front Panel
2 Speaker
FIGURE
8-1
8-1
8-2
CD-C1W
9-1
9-1
Side Panel
(Right)
(B1)x3
Ø3x10mm
9-1
9-2
9-2
(B2)x4
9-2
Ø3x10mm
9-2
9-3
9-4
9-4
Front Panel
9-5
9-5
10-1
CD Servo
PWB
(C1)x1
Main
PWB
– 8 –
PROCEDURE
1. Net ........................... (A1) x1
2. Net Holder ............... (A2) x4
3. Screw ...................... (A3) x4
4. Screw ...................... (A4) x2
1. Screw ...................... (B1) x2
2. Screw ...................... (B2) x2
3. Bracket .................... (B3) x1
4. Screw ...................... (B4) x2
5. Screw ...................... (B5) x4
Top Cabinet
(A1)x2
Ø3x12mm
Side Panel
(Left)
Rear Panel
Figure 8-1
Figure 8-2
FIGURE
10-2
10-3
Front Panel
(A1)x2
Ø3x12mm
(B1)x3
Ø3x10mm
(C3)x2
Ø3x12mm
CD Changer Block
CD Changer
Holder
(C2)x2
Ø3x10mm
Rear
Panel