Service Adjustment Data Table - Sanyo PDG-DET100L Service Manual

Electrical Adjustment

Service Adjustment Data Table

Grp / No. Item
0 AD Converter (PW392)
3 ADC G-GAIN
4 ADC R-GAIN
5 ADC B-GAIN
10 SOGTH
11 SOGHYSDIS
12 HS1TH
13 HS0TH
10 AD Converter (ISL51002/ISL98001)
3 ADC G-GAIN
4 ADC R-GAIN
5 ADC B-GAIN
20 Video Decoder
0 Y Level
1 C Level
10 XCXL Parameter
11 Sync Amp Low
12 Sync Amp High
13 Luma Setup Enable
14 Anti-Alias Filter
15 Anti-Alias Downsample
16 Anti-Alias High Frequency
Comb 3D Cross-Luma Top/Bottom
20
Amplitude
35 DVI Equalizer (DS16E5110)
0 CH0 Boost Data
1 CH1 Boost Data
2 CH2 Boost Data
40 General
0 IP Mode
1 3:2 PullDown Mode
2 Detect Film Mode Enable
3 NR Enable for Analog YUV
4 NR Enable for Digital YUV
41 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE Low Pass Filter Enable
42 Deinterlacer setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE Low Pass Filter Enable
47 Noise Reduction (time)
0 Noise Pixel Range
1 Noise Region 0
2 Noise Region 1
3 Noise Region 2
4 Noise Gain Level
49 Noise Reduction (time)
0 Noise Pixel Range
1 Noise Region 0
Function
RGB (OnBoard/Slot) / YCbCr (OnBoard/Slot) / SCART
RGB (OnBoard/Slot) / YCbCr (OnBoard/Slot) / SCART
RGB (OnBoard/Slot) / YCbCr (OnBoard/Slot) / SCART
RGB / COMPONENT / SCART
RGB / COMPONENT / SCART
H Sync1 Threshold RGB / COMPONENT / SCART
H Sync0 Threshold RGB / COMPONENT / SCART
RGB (OnBoard) / RGB (Slot) / YCbCr (OnBoard/Slot)
RGB (OnBoard) / RGB (Slot) / YCbCr (OnBoard/Slot)
RGB (OnBoard) / RGB (Slot) / YCbCr (OnBoard/Slot)
XCXL Level
Minimum sync amplitude threshold for HLOCK 1 to 0 transition
Minimum sync amplitude threshold for HLOCK 0 to 1 transition
7.5IRE Mode (NTSC only)
Anti-Alias Filter
Anti-Alias Downsample
Anti-Alias High Frequency
for PAL/SECAM only
Boost Setting Value
Boost Setting Value
Boost Setting Value
Set at IP OFF 0: Not used IP Block 1: Used IP Block and IP OFF
bit0: Global Motion bit1: Video Motion
0: 2:3pull down & 2:2pull down 1: 2:3pull down 2: 2:2pull down
0 : Noise Reduction detected with Y and UV motion 1 : Noise
Reduction detected with Y motion
Progressive Mode1, Film Parameter
<KDEINT>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
Progressive Mode2 Parameter
<KDEINT>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
NR L1 Parameter
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
<NSREGIONY1> / <NSREGIONUV1>
<NSREGIONY2> / <NSREGIONUV2>
<NSFILTERY**> / <NSFILTERUV**>
NR L2 Parameter
<NSRANGEY> / <NSRANGEUV>
<NSREGIONY0> / <NSREGIONUV0>
These initial values are the reference data written from the
CPU ROM to memory IC when replaced new memory IC. The
adjustment items indicated with "✻" are required to readjust fol-
lowing to the "Electrical adjustments". Other items should be
used with the initial data value.
Range
0 - 1023
0 - 1023
0 - 1023
0 - 15
0 - 1
0 - 15
0 - 15
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 1023
0 - 4
0 - 9999
0 - 9999
0 - 1
0 - 7
0 - 3
0 - 3
0 - 3
0 - 7
0 - 7
0 - 7
0 - 1
1 - 3
0 - 2
0 - 1
0 - 1
0 - 255
0 - 5
0 - 255
0 - 255
0 - 5
0 - 255
0 - 2
0 - 1023
0 - 1023
0 - 1023
0 - 255
0 - 2
0 - 1023
-46-
Initial Note
265/210/229
265/235/232
255/225/233
2 / 4 / 4
2 / 1 / 0
4 / 4 / 4
4 / 4 / 4
290/290/170
290/290/170
290/290/140
153
410
2
1792
4096
0
4
0
3
3
1
1
1
1
1
0
1
0
30/30/30
4/4/4
0/0/0
0/0/0
2/2/2
0/0/0
1
12
24
40
100
1
12