Page 1: Quick Reference
CAMRY CUSTOMER EXPERIENCE CENTER 2 0 1 0 1-800-331-4331 QUICK REFERENCE GUIDE Printed in U.S.A. 1/09 00505-QRG10-CAM 08-TCS-02939 I n f o r ma t i o n P r o v i d e d b y :...
Page 2 Wheel nut wrench Without compact spare tire Jack Your dealership and the entire staff of Toyota Motor Sales, Spare tire U.S.A., Inc. wish you many years of satisfied driving in your new Camry. Removing the spare tire A word about safe vehicle operations (1) Loosen and remove the nut.
Page 3: Table Of Contents
Seatbelts-Shoulder belt anchor Spare tire & tools Tire Pressure Monitoring (warning) System 24 Trunk-Internal release Visit your Toyota dealer for information on customizing this feature. Programmable by customer. Refer to the Owner’s Manual for instructions and more information. ® HomeLink is a registered trademark of Johnson Controls, Inc.
Page 4: Steering Wheel Audio Controls
OVERVIEW Instrument panel Steering wheel controls XLE and LE models Steering wheel controls SE model Steering wheel audio controls Steering wheel climate controls Multi-information display button Voice command button Telephone controls “ENGINE START STOP” button (Smart Key) Ignition switch (standard key) Headlight and turn signal controls/Headlight, turn signal and front fog light controls...
Page 5 Automatic Air Conditioning Manual Air Conditioning Audio system Tire Pressure Monitoring (warning) System Cruise control Tilt and telescopic steering lock release VSC OFF switch Power outside rearview mirror controls Air Conditioning controls Outside rearview mirror /Rear window defogger button AUX or USB/AUX audio jack 12V DC Power outlet Seat heater controls If equipped...
Page 6: Instrument Cluster
If indicator does not turn off within a few seconds of starting engine, there may be a malfunction. Have vehicle inspected by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 7 Driver seatbelt reminder (alarm will sound if speed is over 12 mph) Front passenger seatbelt reminder (alarm will sound if speed is over 12 mph) Charging system warning Front passenger occupant classification or front passenger AIR BAG ON/OFF indicator Low engine oil pressure warning Malfunction/Check Engine indicator Engine oil replacement reminder Low fuel level warning...
Page 8 OVERVIEW Keyless entry (if equipped) Locking operation Without Smart Key system With Smart Key system Push Unlocking operation Without Smart Key system With Smart Key system Push ONCE: Driver door TWICE: All doors NOTE: If a door is not opened within 60 seconds of unlocking, all doors will relock for safety.
Page 9 Smart Key system (if equipped) Start function Green indicator ON Carrying Depress Push brake pedal NOTE: Gear shift lever must be in Park and brake pedal depressed. Power (without starting engine) Without depressing the brake pedal, pressing the “ENGINE START STOP” switch will change the operation mode in succession from: Accessories such as the radio will operate.
Page 10: Fuel Tank Door Release And Cap
OVERVIEW Fuel tank door release and cap Pull up Turn Store NOTE: Tighten until one click is heard. If the cap is not tightened enough, Check Engine “ ” indicator may illuminate. Light control-Instrument panel Brightness control I n f o r ma t i o n P r o v i d e d b y :...
Page 11: Engine Maintenance
Hood release Pull Pull up latch and raise hood Engine maintenance 4 cylinder (2AR-FE) engine 6 cylinder (2GR-FE) engine Engine oil filler cap Engine oil level dipstick Windshield washer fluid tank Engine coolant reservoir Note: Regularly scheduled maintenance, including oil changes, will help extend the life of your vehicle and maintain performance.
Page 12: Auto Lock Functions 2
FEATURES/OPERATIONS Auto lock functions Automatic door locks can be programmed to operate in four different modes, or turned OFF. -Doors lock when shifting from Park.* -Doors lock when the vehicle speed goes above approximately 12 mph. -Doors unlock when shifting into Park.* Vehicles without Smart Key system -Doors unlock when the engine switch is set from “ON”...
Page 13: Parking Brake
Steering lock release Smart Key system* Without Smart Key system Turn Turn Turn Push * Gently turn wheel while pressing the ENGINE START STOP switch. If the lock does not release, the switch will flash green. Tilt and telescopic steering wheel Angle Length Lock release lever...
Page 14: Moonroof
FEATURES/OPERATIONS Windows-Power Driver side Window lock switch Down Automatic operation Push the switch completely down or pull it completely up and release to fully open or close. To stop window midway, lightly push the switch in the opposite direction. Window lock switch Deactivates all passenger windows. Driver’s window remains operable.
Page 15: Seat Adjustments-Front
Seat adjustments-Front Manual seat Power seat Seat position (forward/backward) Height crank (driver side only) Seatback angle Position, cushion angle (driver side only) and height (driver side only) Lumbar support (driver side only) Seat adjustments-Rear (if equipped) Reclining type (XLE model) Fold down type (LE model) Pull Seatback angle...
Page 16: Windshield Wipers & Washers
FEATURES/OPERATIONS Windshield wipers & washers Single wipe Adjust frequency* Interval wipe Slow Fast Pull to wash and wipe * Intermittent windshield wiper frequency adjustment Rotate to increase/decrease wipe frequency. Lights & turn signals Headlights Low beam High beam Headlights Parking lights Auto DRL OFF High beam flasher...
Page 17: Multi-Information Display
Power outlets-12V DC Front console Center console (if equipped) The “ENGINE START STOP” switch/engine switch must be in the “ACC” or “ON” position to be used. Multi-information display (if equipped) Push “DISP” to change information in the following: (1) Outside temperature (2) Miles left on remaining fuel (3) Current gas mileage (4) Running distance from engine start...
Page 18: Cruise Control
Refer to “Garage door opener,” Section 3-7 in the Owner’s Manual for more details. For programming assistance, contact the Toyota Customer Experience Center at 1-800-331-4331, or visit http://www.homelink.com. ®...
Page 19: Sunshade-Rear
Telephone controls (Bluetooth ® (if equipped) Audio unit Microphone Steering wheel telephone switches XLE and LE models SE model Volume Volume Start call End call End call Start call Voice command Voice command button button ® Bluetooth technology allows dialing or receipt of calls without taking hands from the steering wheel or using a cable to connect the compatible telephone and the system.
Page 20: Clock
FEATURES/OPERATIONS Clock H-Hour set M-Minute set Air Conditioning/Heating Manual Air Conditioning Fan speed Temperature selector Airflow vent In “ ” mode, use fresh air (“ ” indicator OFF) to reduce window fogging. “ ” mode uses fresh air only. Outside rearview mirror*/Rear defogger Air Conditioning ON/OFF Use fresh air to quickly cool interior, then change to recirculate for cooler air.
Page 21: Seat Heaters
Automatic Air Conditioning Temperature selector (driver side) “DUAL” button Indicator ON: Separate temperature settings for driver and passengers. Indicator OFF: Synchronize temperature settings for driver and passengers. Fan speed Airflow vent In “ ” mode, use fresh air (“ ” indicator OFF) to reduce window fogging.
Page 22 FEATURES/OPERATIONS Audio Type 1 Eject CD Push to adjust tone & balance Push to turn ON/OFF Push to skip up/down folder Seek station/ CD track select Station/CD track scan Mode Mute/pause View CD text Preset buttons - functions in other modes indicated above number Type 2 additional functions Load CD(s)
Page 23: Steering Wheel Switches
RADIO To preset stations Tune in the desired station and hold down a preset button until you hear a beep. Push desired preset button to select. To scan stations Push and hold “SCAN” to scan preset stations. Push again to hold selection. AUX or USB/AUX audio jack AUX audio jack USB/AUX audio jack...
Page 24: Cup Holders
FEATURES/OPERATIONS Cup holders Front Manual Transmission models Not removable Automatic Transmission models XLE and SE models LE model Push to open Pull to open Rear XLE and SE models LE model I n f o r ma t i o n P r o v i d e d b y :...
Page 25: Door Locks
SAFETY AND EMERGENCY FEATURES Door locks Unlock Lock Doors-Child safety locks Rear door Moving the lever to “LOCK” will allow the door to be opened only from the outside. Seatbelts Take up slack Too high Keep as low on hips as possible If belt is fully extended, then retracted even slightly, it cannot be re-extended beyond that point, unless fully retracted again.
Page 26: Child Comfort Guide
If the tire pressure indicator flashes for more than 60 seconds and then remains on, take the vehicle to your local Toyota dealer. Note: The warning light may come on due to temperature changes or changes in tire pressure from natural air leakage. If the system has not been initialized recently, setting the tire pressures to factory specifications should turn off the light.
Page 27 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor Child Restraint System DISP Display Electronic Control Unit Event data recorder Emergency Locking Retractor GAWR Gross Axle Weight Ratings GVWR Gross Vehicle Weight Rating Emission inspection and maintenance LATCH Lower Anchors and Tethers for Children Light Emitting Diode...
Page 28 TABLE OF CONTENTS Index 1-6. Theft deterrent system Before driving Engine immobilizer system ........ 80 Alarm ........82 1-1. Key information Theft prevention labels Keys ........24 (for U.S.A.) ......84 1-2. Opening, closing and 1-7. Safety information locking the doors Correct driving posture ..
Page 29 2-3. Operating the lights Using the CD player ... 223 and wipers Playing MP3 and WMA discs ......... 232 Headlight switch....159 ® Operating an iPod Fog light switch ....163 player ....... 240 Windshield wipers and Operating a USB memory washer ......
Page 30 TABLE OF CONTENTS Index 3-5. Using the interior lights Maintenance and care Interior lights list ....313 • Interior light ...... 314 • Personal lights ....315 4-1. Maintenance and care Cleaning and protecting 3-6. Using the storage features the vehicle exterior ... 348 List of storage features..
Page 31 When trouble arises Vehicle specifications 5-1. Essential information 6-1. Specifications Maintenance data Emergency flashers .... 424 (fuel, oil level, etc.) ... 482 If your vehicle needs to Fuel information....495 be towed ......425 If you think something Tire information ....498 is wrong ......
Page 32: For Your Information
A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that these parts are not covered by Toyota warranty and that Toyota is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 33 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 34 CAUTION ■ General precautions while driving Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 35 This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
Page 36 I n f o r ma t i o n P r o v i d e d b y :...
Page 37: Before Driving
TABLE OF CONTENTS Adjusting and operating features such as door locks, Before driving mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior fea- Air conditioning and audio systems, as well as other in- tures terior features for a comfortable driving experience. Maintenance Cleaning and protecting your vehicle, performing do-it- and care...
Page 38 Pictorial index Exterior Headlights (low beam) Side marker/parking lights P. 159 P. 159 ∗ Moon roof P. 72 Headlights (high beam) P. 160 Outside rear view Hood P. 362 mirrors P. 68 Turn signal lights P. 144 Windshield wipers P. 164 ∗...
Page 39 Rear window defogger P. 209 Rear turn signal lights P. 144 Fuel filler door P. 76 Trunk P. 47 Doors P. 42 Stop/tail lights P. 159 Tires ●Rotation P. 382 ●Replacement P. 454 Rear side marker light P. 159 ●Inflation pressure P.
Page 40 Pictorial index Interior Head restraints SRS driver airbag P. 55 P. 87 Floor mat P. 335 Seat belts P. 57 Power window SRS front passenger switches airbag P. 70 P. 87 Glove box P. 317 Armrest P. 332 Front seats P.
Page 41 Vehicles with moon roof Vanity mirrors P. 325 Sun visors P. 324 Auxiliary box P. 321 Moon roof switches P. 72 Front personal lights P. 315 Interior light P. 313 SRS curtain shield airbags P. 87 Rear personal lights P. 315 ∗...
Page 42 Pictorial index Interior Vehicles without moon roof Vanity mirrors P. 325 Sun visors P. 324 Auxiliary box P. 321 Front personal lights P. 315 SRS curtain shield airbags P. 87 Interior light P. 314 ∗ Garage door opener switches P. 338 Anti-glare inside rear view mirror P.
Page 43 Inside lock button Door lock switch P. 43 P. 42 Window lock switch P. 70 Power window switches P. 70 ∗ : If equipped I n f o r ma t i o n P r o v i d e d b y :...
Page 44 Pictorial index Interior Automatic transmission Automatic transmission shift lever P. 138 Shift lock override Cup holders P. 319 button P. 467 Auxiliary box P. 321 Power outlet P. 328 Manual transmission Manual transmission shift lever P. 142 Cup holders P. 319 Parking brake lever P.
Page 45: Instrument Panel
Pictorial index Instrument panel Headlight switch Gauges and meters P. 159 P. 147 ∗ Turn signal lever Multi-information display P. 144 P. 155 ∗ Fog light switch P. 163 VSC OFF switch P. 171 Clock P. 326 Security indicator P. 80, 82 Emergency Audio system P.
Page 46 Pictorial index Instrument panel Automatic air conditioning system Air conditioning system P. 196 Rear window and outside rear view mirror defogger switch P. 209 Manual air conditioning system Air conditioning system P. 204 Rear window defogger switch P. 209 ∗ Outside rear view mirror defogger switch P.
Page 47 Type A ∗ “DISP” switch P. 156 Audio remote control Air conditioning remote ∗ switches P. 260 control switches P. 201 ∗ Telephone switches P. 284 Engine (ignition) switch (vehicles without smart key system) P. 135 ∗ Talk switch P. 284 Cruise control switch P.
Page 48 Pictorial index Instrument panel Type B Engine (ignition) switch (vehicles without smart key system) P. 135 Audio remote control ∗ Telephone switches switches P. 260 P. 284 Cruise control switch P. 166 Engine (ignition) switch (vehicles with smart key system) P.
Page 49 Power outlet P. 328 ∗ USB/AUX adapter P. 240, 246 ∗ AUX adapter P. 258 Cable pass-through P. 323 ∗ Seat heater switches P. 330 ∗ : If equipped : Refer to “Navigation System Owner’s Manual”. I n f o r ma t i o n P r o v i d e d b y :...
Page 50: 1-1. Key Information
1-1. Key information Keys The following keys are provided with the vehicle. Vehicles with smart key system Electronic keys • Operating the smart key system (→P. 27) • Operating wireless remote control function (→P. 38) Mechanical keys Key number plate Vehicles without smart key system (type A) Master keys Operating the wireless remote...
Page 51 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 468) ■...
Page 52 1-1. Key information NOTICE ■ To prevent key damage ● Do not subject the keys to strong shocks, expose them to high tempera- tures by placing them in direct sunlight, or get them wet. ● Do not expose the keys to electromagnetic materials or attach any mate- rial that blocks electromagnetic waves to the key surface.
Page 53: Opening, Closing And
1-2. Opening, closing and locking the doors and trunk ∗ Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) Locks and unlocks the doors (→P.
Page 54 1-2. Opening, closing and locking the doors and trunk Unlocking and locking the doors (front door handles only) Grip the handle to unlock the door. Make sure to touch the sensor on the back of the handle. The door cannot be unlocked for 3 seconds after the door is locked.
Page 55 1-2. Opening, closing and locking the doors and trunk Antenna location and effective range ■ Antenna location Antennas outside the cabin Antenna outside the trunk Antenna inside the trunk Antennas inside the cabin I n f o r ma t i o n P r o v i d e d b y :...
Page 56 1-2. Opening, closing and locking the doors and trunk ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the outside front door handles.
Page 57 1-2. Opening, closing and locking the doors and trunk ● Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise ● When carrying a portable radio, cellular phone, cordless phone or other wireless communication devices ●...
Page 58 1-2. Opening, closing and locking the doors and trunk STEP Unlock the doors using the electronic key and open one of the doors. If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set. In case that the alarm is triggered, immediately stop the alarm.
Page 59 1-2. Opening, closing and locking the doors and trunk ■ Note for the smart key system ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases. • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
Page 60 1-2. Opening, closing and locking the doors and trunk ■ Alarms and warning indicators A combination of exterior and interior alarms as well as warning messages shown on the multi-information display are used to reduce the chance of vehicle theft and accidents resulting from erroneous operation. ●...
Page 61 When the electronic key battery is fully depleted →P. 401 ■ Customization that can be configured at Toyota dealer It is possible to deactivate the smart key system, etc. (Customizable features →P. 510) I n f o r ma t i o n P r o v i d e d b y :...
Page 62 1-2. Opening, closing and locking the doors and trunk ■ Certification for the smart key system For vehicles sold in the U.S.A. FCC ID: NI4TMLF-3 NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 63 (→P. 29) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves.
Page 64: Wireless Remote Control
1-2. Opening, closing and locking the doors and trunk ∗ Wireless remote control The wireless remote control can be used to lock and unlock the vehi- cle from outside the vehicle. Vehicles with smart key system Locks all doors Unlocks all doors Pressing the button unlocks the driver’s door.
Page 65 1-2. Opening, closing and locking the doors and trunk ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Trunk: A buzzer sounds to indicate that the trunk has been unlocked. ■...
Page 66 1-2. Opening, closing and locking the doors and trunk ■ Key battery depletion Vehicles with smart key system →P. 32 Vehicles without smart key system The standard battery life is 1 to 2 years. (The battery becomes depleted even if the key is not used.) If the wireless remote control function does not operate, the battery may be depleted.
Page 67 1-2. Opening, closing and locking the doors and trunk ■ Customization that can be configured at Toyota dealer Settings (e.g. trunk unlocking function) can be changed. (Customizable features →P. 510) ■ Certification for wireless remote control For vehicles sold in the U.S.A.
Page 68: Doors
1-2. Opening, closing and locking the doors and trunk Doors The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with smart key system) →P. 27 ■ Wireless remote control (if equipped) →P.
Page 69 1-2. Opening, closing and locking the doors and trunk ■ Inside lock button Unlocks the door Locks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position. Locking the front doors from the outside without a key Vehicles with smart key system The door cannot be locked if the “ENGINE START STOP”...
Page 70 1-2. Opening, closing and locking the doors and trunk Automatic door locking and unlocking systems The following functions can be set or cancelled: Function Operation Shift position linked Shifting the shift lever out of P locks all door locking function doors.
Page 71 1-2. Opening, closing and locking the doors and trunk ■ Setting and canceling the functions To switch between setting and canceling, follow the procedure below: Vehicles with smart key system: STEP Close all the doors and switch the “ENGINE START STOP” switch to IGNITION ON mode.
Page 72 1-2. Opening, closing and locking the doors and trunk When the setting or canceling operation is complete, all doors are locked and then unlocked. ■ Customization that can be configured at Toyota dealer Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 510) CAUTION ■...
Page 73: Trunk
1-2. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the key, trunk opener, entry function or wireless remote control. ■ Opening the trunk from outside the vehicle Entry function (vehicles with smart key system) →P.
Page 74 1-2. Opening, closing and locking the doors and trunk Luggage security system To protect luggage stored in the trunk against theft, do the following procedure. Turn the master key (vehicles without smart key system) or mechanical key (vehicles with smart key system) counterclock- wise to lock the trunk opener fea- ture.
Page 75 1-2. Opening, closing and locking the doors and trunk CAUTION ■ Caution while driving ● Keep the trunk lid closed while driving. If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
Page 76 ● Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to fall closed again after it is opened.
Page 77: Adjustable Components
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats Power seat Seat position switch Seatback angle switch Seat cushion (front) angle switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support switch (driver’s side only) I n f o r ma t i o n P r o v i d e d b y :...
Page 78 1-3. Adjustable components (seats, mirrors, steering wheel) Manual seat Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only) CAUTION ■ Seat adjustment ● Do not recline the seat more than necessary when the vehicle is in motion to reduce the risk of sliding under the lap belt.
Page 79: Rear Seats
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats ■ Adjusting the rear seat (if equipped) Pull up the seatback angle adjustment lever until the lock is completely released. I n f o r ma t i o n P r o v i d e d b y :...
Page 80 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Folding down rear seatbacks (if equipped) Pull the seatback lever in the trunk for the seatback you wish to fold down. CAUTION ■ After returning the seatback to the upright position Observe the following precautions. Failure to do so may result in death or serious injury.
Page 81: Head Restraints
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Pull the head restraints up. Down Push the head restraint down while pushing the lock release button. Lock release button ■ Removing the head restraints Pull the head restraint up while pressing the lock release button.
Page 82 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. ■ Adjusting the rear center seat head restraint Always raise the head restraint one level from the stowed position when using.
Page 83: Seat Belts
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
Page 84 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the belt (front seats) Down Move the height adjuster up and down as needed until you hear a click. Seat belt comfort guide (outside rear seat) If the shoulder belt fits close to a person's neck, use the seat belt comfort guide.
Page 85 1-3. Adjustable components (seats, mirrors, steering wheel) Buckle, position and release the STEP seat belt. Seat belt pretensioners (front seats) The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal collision.
Page 86 1-3. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Page 87 Toyota dealer free of charge. ■ Rear seat belt Use the seat belt after passing it through the guide if the seat belt comes free from the guide.
Page 88 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
Page 89 ● Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 90 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Using a seat belt comfort guide ● Make sure the belt is not twisted and that it lies flat. The elastic cord must be behind the belt and the guide must be on the front. ●...
Page 91: Steering Wheel
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and STEP press the lever down. Adjust to the ideal position by STEP moving the steering wheel horizontally and vertically.
Page 92: Anti-Glare Inside Rear View Mirror
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions. Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Page 93 1-3. Adjustable components (seats, mirrors, steering wheel) ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them. CAUTION ■ Caution while driving Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
Page 94: Outside Rear View Mirrors
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. Select a mirror to adjust. STEP Left Right Adjust the mirror. STEP Right Down Left ■ Mirror angle can be adjusted when Vehicles with smart key system The “ENGINE START STOP”...
Page 95 1-3. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When driving the vehicle Observe the following precautions while driving. Failing to do so may result in loss of control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●...
Page 96: Power Windows
1-4. Opening and closing the windows Power windows The power windows can be opened and closed using the following switches. Closing One-touch closing Opening One-touch opening Pressing the switch in the opposite direction will stop win- dow travel partway. Lock switch Press the switch down to lock passenger window switches.
Page 97 1-4. Opening and closing the windows ■ The power windows can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
Page 98: Moon Roof
1-4. Opening and closing the windows ∗ Moon roof Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing Open The moon roof stops slightly before the fully open position. Push the switch again to fully open.
Page 99 1-4. Opening and closing the windows ■ The moon roof can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
Page 100 If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 101 1-4. Opening and closing the windows CAUTION ■ Opening the moon roof Observe the following precautions. Failing to do so may cause death or serious injury. ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 102: Refueling Opening The Fuel Tank Cap
1-5. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle Vehicles with smart key system Turn the “ENGINE START STOP” switch OFF and ensure that all the doors and windows are closed. Vehicles without smart key system Turn the engine switch to the “LOCK”...
Page 103 1-5. Refueling Hang the fuel tank cap on the STEP back of the fuel filler door. Closing the fuel tank cap When replacing the fuel tank cap, turn it until a clicking sound is heard. After releasing your hand, the cap will turn slightly to the opposite direction.
Page 104 ■ When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury. I n f o r ma t i o n P r o v i d e d b y :...
Page 105 1-5. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface. I n f o r ma t i o n P r o v i d e d b y :...
Page 106: 1-6. Theft Deterrent System
1-6. Theft deterrent system Engine immobilizer system The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. Vehicles with smart key sys- tem: The indicator light flashes after the “ENGINE START...
Page 107 1-6. Theft deterrent system ■ Certifications for the engine immobilizer system (for vehicles sold in U.S.A.) Vehicles with smart key system FCC ID: NI4TMIMB-1 Vehicles without smart key system FCC ID: MOZRI-20BTY (Made in Japan) FCC ID: MOZRI-21BTY (Made in Canada) This device complies with Part 15 of the FCC Rules.
Page 108: Alarm
1-6. Theft deterrent system ∗ Alarm The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations: ● A locked door or trunk is unlocked or opened without the key, wireless remote control or entry function of the smart key sys- tem.
Page 109 1-6. Theft deterrent system ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ● Nobody is in the vehicle. ● The windows and moon roof are closed before the alarm is set. ●...
Page 110: Theft Prevention Labels (For U.s.a.)
1-6. Theft deterrent system Theft prevention labels (for U.S.A.) These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law. I n f o r ma t i o n P r o v i d e d b y :...
Page 111: 1-7. Safety Information
1-7. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 51) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
Page 112 1-7. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver's seat while driving. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Page 113: Srs Airbags
1-7. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas-...
Page 114 1-7. Safety information Airbag system components Front airbag sensors Airbag sensor assembly Front passenger occupant Curtain shield airbag sen- classification system (ECU sors and sensors) Driver airbag Side and curtain shield air- Driver’s seat position sen- bag sensors sor (with power seat) Front passenger airbag Driver’s seat belt buckle Side airbags...
Page 115 1-7. Safety information Your vehicle is equipped with ADVANCED AIRBAGS designed based on US motor vehicle safety standards (FMVSS208). The airbag sys- tem controls airbag deployment power for the driver and front pas- senger. The driver airbag system consists of the driver seat's position sensor etc.
Page 116 1-7. Safety information ■ SRS warning light This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensors, curtain shield airbag sen- sors, driver's seat position sensor, driver's seat belt buckle switch, front pas- senger occupant classification system, “AIR BAG ON”...
Page 117 1-7. Safety information ■ SRS airbag deployment conditions (side airbags and curtain shield air- bags) ● The SRS side airbags and SRS curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to the impact force produced by a 3300 lb.
Page 118 1-7. Safety information ■ Types of collisions that may not deploy the SRS airbag (side airbags and curtain shield airbags) The SRS side airbags and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a col- lision to the side of the vehicle body other than the passenger compartment.
Page 119 1-7. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer. ● Any of the SRS airbags have been inflated.
Page 120 1-7. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly. The SRS airbags are supplemental devices to be used with the seat belts.
Page 121 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children.
Page 122 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. ● Do not drive the vehicle while the driver or passenger has items resting on their knees.
Page 123 1-7. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip. ● Do not hang coat hangers or other hard objects on the coat hooks.
Page 124 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillars garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ■ Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer.
Page 125: Front Passenger Occupant Classification System
1-7. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
Page 126 1-7. Safety information Conditions and operation of the front passenger occupant classification system ■ Adult “AIR BAG ON” and “AIR BAG OFF” indicator “AIR BAG lights ON” Indicator/ SRS warning light warning light Front passenger’s seat belt reminder light Flashing Front passenger airbag Side airbag on the front passenger seats...
Page 127 1-7. Safety information ■ Unoccupied “AIR BAG ON” and “AIR BAG OFF” indicator Not illuminated lights Indicator/ warning light SRS warning light Front passenger’s seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seats Devices Curtain shield airbag in the front Activated passenger side...
Page 128 1-7. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 104) : In case the indicator is not illuminated, consult this manual as for installing the child restraint system properly.
Page 129 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 130: Child Restraint Systems
1-7. Safety information Child restraint systems A child restraint system for a small child or baby must be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of U.S.A. and Canada now require the use of child restraint systems.
Page 131 1-7. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child. Rear facing ⎯ Infant seat/convertible seat Forward facing ⎯ Convertible seat Booster seat I n f o r ma t i o n P r o v i d e d b y :...
Page 132 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 133 1-7. Safety information CAUTION ■ Child restraint precautions ● Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or collision.
Page 134: Installing Child Restraints
1-7. Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the outside rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
Page 135 1-7. Safety information Anchor bracket (for top tether strap) Anchor brackets are provided for all rear seats. Installation with LATCH system Vehicles with reclining type rear seat: Adjust the seatback as STEP upright as possible. Type A Widen the gap between STEP the seat cushion and seatback slightly.
Page 136 1-7. Safety information Type B Widen the gap between STEP the seat cushion and seatback slightly. Latch the buckles onto STEP the LATCH anchors. If the child restraint has a STEP top tether strap, the top tether strap should be latched onto tether strap anchor.
Page 137 1-7. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear facing ⎯ Infant seat/convertible seat ■ Place the child seat on the rear STEP seat facing the rear of the vehi- cle. Run the seat belt through the STEP child seat and insert the plate into the buckle.
Page 138 1-7. Safety information While pushing the child seat STEP down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that in cannot be extended.
Page 139 1-7. Safety information While pushing the child seat into STEP the rear seat, allow the shoulder belt to retract until the child seat is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 140 1-7. Safety information Removing a child restraint installed with a seat belt Push the release button and fully retract the seat belt. Child restraint systems with a top tether strap Secure the child restraint using STEP the seat belt or LATCH anchors. Remove the head restraint.
Page 141 1-7. Safety information ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819. CAUTION ■...
Page 142 1-7. Safety information CAUTION ■ When installing a child restraint system Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.
Page 143 1-7. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder.
Page 144 1-7. Safety information I n f o r ma t i o n P r o v i d e d b y :...
Page 145: 2-1. Driving Procedures
2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing: ■ Starting the engine →P. 131, 135 ■ Driving Automatic transmission With the brake pedal depressed, shift the shift lever to D. STEP (→P.
Page 146 2-1. Driving procedures ■ Parking the vehicle Automatic transmission With the shift lever in D, depress the brake pedal. STEP Set the parking brake. (→P. 145) STEP Shift the shift lever to P. (→P. 138) STEP When parking on a hill, if necessary, block the wheels. Vehicles with smart key system: STEP Turn the “ENGINE START STOP”...
Page 147 ■ Breaking in your new Toyota To extend the life of the vehicle, the following precautions are recommended to observe: ●...
Page 148 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.
Page 149 If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately. ●...
Page 150 2-1. Driving procedures CAUTION ● When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident. ● Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving.
Page 151 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not race the engine. If the vehicle is in any gear other than P (automatic transmission only) or N the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.
Page 152 The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
Page 153 2-1. Driving procedures CAUTION ■ When braking the vehicle ● When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.
Page 154 2-1. Driving procedures NOTICE ■ When driving the vehicle Manual transmission ● Do not shift gears unless the clutch pedal is fully depressed. After shifting, do not release the clutch abruptly. Doing so may damage the clutch, trans- mission and gears. ●...
Page 155 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed.
Page 156: Engine (Ignition) Switch (Vehicles With Smart Key System)
2-1. Driving procedures Engine (ignition) switch (vehicles with smart key system) Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine Check that the parking brake is set. STEP Check that the shift lever is set in P.
Page 157 2-1. Driving procedures ■ Changing “ENGINE START STOP” switch mode Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal released. (The mode changes each time the switch is pressed.) OFF* Emergency flashers can be used.
Page 158 ■ When the “ENGINE START STOP” switch indicator flashes in amber The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. ■ Auto power OFF function If the vehicle is left in ACCESSORY mode for more than an hour with the shift lever in P, the “ENGINE START STOP”...
Page 159 2-1. Driving procedures CAUTION ■ When starting the engine Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury. ■...
Page 160: Engine (Ignition) Switch (Vehicles Without Smart Key System)
2-1. Driving procedures Engine (ignition) switch (vehicles without smart key system) ■ Starting the engine Automatic transmission Check that the parking brake is set. STEP Check that the shift lever is set in P. STEP Sit in the driver’s seat and firmly depress the brake pedal. STEP Turn the engine switch to the “START”...
Page 161 2-1. Driving procedures ■ Turning the key from “ACC” to “LOCK” Shift the shift lever to N (manual STEP transmission) or P (automatic transmission). (→P. 138, 142) Push in the key and turn to the STEP “LOCK” position. ■ Steering lock release When starting the engine, the engine switch may seem stuck in the “LOCK”...
Page 162 2-1. Driving procedures NOTICE ■ To prevent battery discharge Do not leave the key in the “ACC” or “ON” position for long periods if the engine is not running. ■ When starting the engine ● Do not crank for more than 30 seconds at a time. This may overheat the starter and wiring systems.
Page 163: Automatic Transmission
2-1. Driving procedures ∗ Automatic transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, depress the brake pedal and move the shift lever. Vehicles without smart key system: While the engine switch is in the “ON”...
Page 164 2-1. Driving procedures ■ Shift position uses Shift position Function Parking the vehicle or starting the engine Reversing Neutral Normal driving S mode driving (→P. 139) : Shifting to the D position allows the system to select a gear suitable for the driving conditions.
Page 165 2-1. Driving procedures ■ Shift ranges and their functions Shift range Function A gear between 1 and 6 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 5 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 4 is automatically selected according to vehicle speed and driving conditions.
Page 166 If the “S” indicator does not come on even after shifting the shift lever to S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the vehicle will operate as if the shift lever is in D.) ■...
Page 167: Manual Transmission
2-1. Driving procedures ∗ Manual transmission ■ Shifting the shift lever Fully depress the clutch pedal before operating the shift lever, and then release it slowly. ■ Shifting the shift lever to R Shift the shift lever to the R position while lifting up the ring section.
Page 168 2-1. Driving procedures ■ Maximum allowable speeds Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary. mph (km/h) Shift position Maximum speed 32 (52) 56 (91) 83 (135) 118 (191) 130 (210) NOTICE ■ To prevent damage to the transmission ●...
Page 169: Turn Signal Lever
2-1. Driving procedures Turn signal lever Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change.
Page 170: Parking Brake
2-1. Driving procedures Parking brake Manual transmission U.S.A. Canada Sets the parking brake Fully apply the parking brake while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while pressing the but- ton. Automatic transmission Sets the parking brake* (Depressing the pedal again...
Page 171: Horn
2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
Page 172: Instrument Cluster Gauges And Meters
2-2. Instrument cluster Gauges and meters Vehicles with multi-information display Vehicles with smart key system: The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: The following gauges, meters and displays illuminate when the engine switch is in the “ON”...
Page 173 2-2. Instrument cluster Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button.
Page 174 2-2. Instrument cluster Vehicles without multi-information display The following gauges, meters and displays illuminate when the engine switch is in the “ON” position. Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed.
Page 175 2-2. Instrument cluster Odometer, trip meter and outside temperature display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
Page 176: Indicators And Warning Lights
2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster (vehicles with multi-information display) Instrument cluster (vehicles without multi-information display) I n f o r ma t i o n P r o v i d e d b y :...
Page 177 2-2. Instrument cluster Center panel I n f o r ma t i o n P r o v i d e d b y :...
Page 178 2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. Turn signal indicator Headlight indicator (→P. 144) (→P. 159) (U.S.A.) Headlight high beam Tail light indicator indicator (→P. 160) (→P. 159) (CANADA) Slip indicator Front fog light indicator...
Page 179: Warning Lights
Have the vehicle inspected by your Toyota dealer immediately if this occurs.
Page 180: Multi-Information Display
2-2. Instrument cluster ∗ Multi-information display The multi-information display presents the driver with a variety of driving-related data, including the outside temperature. ● Outside temperature dis- play (→P. 156) Indicates the outside tempera- ture. ● Trip information (→P. 156) Displays driving range, fuel consumption and other cruis- ing-related information.
Page 181 2-2. Instrument cluster Switch the display Display items can be switched by pressing the “DISP” button. The display will return to the out- side temperature display when the “DISP” button is pressed and held. ● Outside temperature Displays the outside air temperature. The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).
Page 182 2-2. Instrument cluster ● Driving distance Displays the driving distance since the engine was started. ● Average vehicle speed Displays the average vehicle speed since the engine was started. ● Cruise information off Displays the odometer and trip meters only. ●...
Page 183 2-2. Instrument cluster NOTICE ■ The multi-information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed. I n f o r ma t i o n P r o v i d e d b y :...
Page 184: Headlight Switch
2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. For U.S.A. The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn The headlights and parking lights turn on and off automatically.
Page 185 2-3. Operating the lights and wipers For Canada The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn The headlights and parking lights turn on and off automatically. (When the “ENGINE START STOP”...
Page 186 2-3. Operating the lights and wipers ■ The headlights can be operated automatically when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position. ■...
Page 187 If any of the doors or trunk lid is kept open, the lights automatically turn off after 20 minutes. ■ Customization that can be configured at Toyota dealer Settings (e.g. Light sensor sensitivity) can be changed. (Customizable features →P. 510) NOTICE ■...
Page 188: Fog Light Switch
2-3. Operating the lights and wipers ∗ Fog light switch The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam. Front fog lights on ∗...
Page 189: Windshield Wipers And Washer
2-3. Operating the lights and wipers Windshield wipers and washer Wiper intervals can be adjusted for intermittent operation. Intermittent windshield wiper operation Low speed windshield wiper operation High speed windshield wiper operation Temporary operation Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency I n f o r ma t i o n P r o v i d e d b y :...
Page 190 2-3. Operating the lights and wipers Wash/wipe operation Wipers operate automatically. ■ The windshield wiper and washers can be operated when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON”...
Page 191: 2-4. Using Other Driving Systems
2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without using the accelerator. Indicators Cruise control switch ■ Setting the vehicle speed Turn the “ON-OFF” button on. STEP At this time, the cruise control indicator will come on.
Page 192 2-4. Using other driving systems ■ Adjusting the speed setting Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.
Page 193 Contact your Toyota dealer and have your Toyota inspected. I n f o r ma t i o n P r o v i d e d b y :...
Page 194 2-4. Using other driving systems CAUTION ■ To avoid operating the cruise control by mistake Keep the “ON-OFF” button off when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause an accident resulting in death or serious injury.
Page 195: Driving Assist Systems
2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
Page 196 2-4. Using other driving systems To disable TRAC and/or VSC If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■...
Page 197 ■ If the slip indicator comes on... It may indicate a malfunction in the VSC and TRAC. Contact your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 198 2-4. Using other driving systems CAUTION ■ ABS does not operate effectively when ● Tires with inadequate gripping ability are used (such as excessively worn tires on a snow covered road). ● The vehicle hydroplanes while driving at high speed on the wet or slick road.
Page 199 In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.
Page 200: Driving Information Cargo And Luggage
2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the trunk whenever possible. ● Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for- ward as possible helps maintain vehicle balance.
Page 201 2-5. Driving information (6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 183) Example on your vehicle Cargo capacity Total load capacity...
Page 202 2-5. Driving information CAUTION ■ Storage precautions Observe the following precautions. Failing to do so may result in death or serious injury. ● Vehicles with fold-down type rear seat: To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk.
Page 203: Vehicle Load Limits
2-5. Driving information Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 900 lb. (410 kg) Total load capacity means the combined weight of occupants, cargo and luggage. ■...
Page 204: Winter Driving Tips
2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
Page 205 2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P (automatic trans- mission) or R (manual transmission) without setting the parking brake.
Page 206 2-5. Driving information ■ Tire chains Observe the following precautions when installing and removing chains. ● Install and remove tire chains in a safe location. ● Install tire chains on the front tires only. Do not install tire chains on rear tires.
Page 207 NOTICE ■ Repairing or replacing snow tires Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 208: Trailer Towing
Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. ■...
Page 209 Total trailer weight Tongue load Towing a trailer Contact your Toyota dealer for further information about additional requirements such as a towing kits, etc. Hitch Trailer hitch assemblies have different weight capacities established by the hitch manufacturer.
Page 210 ■ Break-in schedule Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.
Page 211 40% in the rear. ■ Hitches ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the total trailer weight requirement. ● Follow the directions supplied by the hitch manufacturer.
Page 212 ■ When installing a trailer hitch ● Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage. ● Do not use axle-mounted hitches, as they can cause damage to the axle housing, wheel bearings, wheels or tires.
Page 213 2-5. Driving information ● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right.
Page 214 2-5. Driving information ● In order to maintain efficient engine braking and electrical charging performance, do not use overdrive (automatic transmission) or the 5th gear (manual transmission). ● Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade.
Page 215 2-5. Driving information CAUTION ■ To avoid an accident ● Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.
Page 216: Dinghy Towing (Automatic Transmission)
2-5. Driving information Dinghy towing (automatic transmission) Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. I n f o r ma t i o n P r o v i d e d b y :...
Page 217: Dinghy Towing (Manual Transmission)
2-5. Driving information Dinghy towing (manual transmission) Your vehicle can be dinghy towed in a forward direction (with 4 wheels on the ground) behind a motor home. Towing your vehicle with 4 wheels on the ground To prevent damage to your vehicle, perform the following procedures before towing.
Page 218 2-5. Driving information NOTICE ■ Dinghy towing direction Do not tow the vehicle backwards. Doing so may cause serious damage. ■ To prevent the steering from locking Ensure the engine switch is in the “ACC” position. I n f o r ma t i o n P r o v i d e d b y :...
Page 219: Automatic Air Conditioning
3-1. Using the air conditioning system and defogger ∗ Automatic air conditioning system Air outlets are automatically selected and fan speed is automatically adjusted according to the temperature setting. Front passenger’s side temperature Air outlet display setting display Driver’s side temperature Fan speed setting display Change the air outlets used...
Page 220 3-1. Using the air conditioning system and defogger Using the automatic mode Press STEP The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting. Turning to the right increases the temperature and STEP turning to the left decreases the temperature on the...
Page 221 3-1. Using the air conditioning system and defogger ■ Adjusting the fan speed Press “∧” (increase) or “∨” (decrease) on the fan speed selector. The fan speed is shown on the display. (7 levels) Press to turn the fan off. ■...
Page 222 3-1. Using the air conditioning system and defogger Air flows to the feet and the windshield defogger operates. Recirculated air mode will auto- matically switch to outside air mode. ■ Switching between outside air and recirculated air modes Press The mode switches between outside air mode (indicator off) and recircu- lated air mode (indicator on) modes each time is pressed.
Page 223 3-1. Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Center outlets Direct air flow to the left or right, up or down. Right and left side outlets Direct air flow to the left or right, up or down.
Page 224 3-1. Using the air conditioning system and defogger Steering wheel switches (if equipped) Some air conditioning features can be controlled using the switches on the steering wheel. Temperature selector “DUAL” button indicator on: Indi- vidual setting on the driver's side only.
Page 225 There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer. ■ Windshield air flow button When any of the following conditions occurs, the indicator light on the button may flash and a motor sound may be heard.
Page 226 Do not disassemble or repair the system because it contains high voltage parts. Call your Toyota dealer if the system needs repair. I n f o r ma t i o n P r o v i d e d b y :...
Page 227 3-1. Using the air conditioning system and defogger NOTICE ■ To prevent battery discharge Do not leave the automatic air conditioning system on longer than necessary when the engine is stopped. ■ To prevent damage to the Plasmacluster™ Do not insert anything into the driver's side vent, attach anything to it, or use sprays around the drive's side vent.
Page 228: Manual Air Conditioning System
3-1. Using the air conditioning system and defogger ∗ Manual air conditioning system Fan speed dial Temperature control dial Air outlet selection dial Air conditioning on/off switch Air intake mode switch Adjusting the settings ■ Adjusting the temperature setting Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).
Page 229 3-1. Using the air conditioning system and defogger ■ Adjusting the fan speed Turn the fan speed dial clockwise (increase) or counterclockwise (decrease). Set the dial to “OFF” to turn the fan off. ■ Selecting the air outlets Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment.
Page 230 3-1. Using the air conditioning system and defogger Air flows to the feet and the windshield defogger operates. The air intake is automatically switched to outside air mode. Pressing to turn the air conditioning on clears the wind- shield and side windows faster. Air flows to the windshield and side windows.
Page 231 3-1. Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Center outlets Direct air flow to the left or right, up or down. Right and left side outlets Direct air flow to the left or right, up or down.
Page 232 There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer. ■ Air conditioning odors ●...
Page 233 3-1. Using the air conditioning system and defogger NOTICE ■ To prevent battery discharge Do not leave the air conditioning system on longer than necessary when the engine is stopped. I n f o r ma t i o n P r o v i d e d b y :...
Page 234: Rear Window And Outside Rear View Mirror Defoggers
3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers Clear the rear window using the defogger. Vehicles with automatic air conditioning system On/off The defoggers will automati- cally turn off the operation time. The operation time is between 15 minutes and 1 hour depending on the ambient temperature...
Page 235 3-1. Using the air conditioning system and defogger CAUTION ■ Outside rear view mirror defoggers (if equipped) The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself. I n f o r ma t i o n P r o v i d e d b y :...
Page 236: 3-2. Using The Audio System
3-2. Using the audio system Audio system types With navigation system Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”. Without navigation system Type A: CD player with changer controller and AM/FM radio Type B: CD player with changer and AM/FM radio I n f o r ma t i o n P r o v i d e d b y :...
Page 237 3-2. Using the audio system Type C: CD player with changer controller and AM/FM radio Title Page Using the radio P. 215 Using the CD player P. 223 Playing MP3 and WMA discs P. 232 ® Operating an iPod player P.
Page 238 3-2. Using the audio system Language settings (type B and C) The language used for all voice guidance, voice recognition and mes- sages may be changed. Press STEP Press that corresponds to “MORE”. STEP Press that corresponds to “LANG”. STEP Press that corresponds to the desired language.
Page 239 3-2. Using the audio system CAUTION ■ For vehicles sold in U.S.A. and Canada ● Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device. ●...
Page 240: Using The Radio
3-2. Using the audio system Using the radio Type A Power Volume Adjusting frequency (AM, FM mode) or channel (SAT mode) Scanning for Station selector receivable stations AM⋅SAT/FM Displaying radio text mode buttons messages Seeking the frequency Changing the channel Type B and C Power Volume...
Page 241 3-2. Using the audio system ® Setting station presets (excluding XM Satellite Radio) Search for desired stations by turning STEP ∧ pressing “ ” or “∨” on Press and hold a button (from or one of STEP ) until you hear a beep. Type B and C: Each time is pressed, station pages are changed.
Page 242 3-2. Using the audio system ■ Displaying radio text messages (for type B and C, FM mode only) When a new radio text message is received, “MSG” is shown on the display. To display the message, press If the text continues past the end of the display, “ ”...
Page 243 3-2. Using the audio system ® ■ Setting XM Satellite Radio channel presets Select the desired channel. Press and hold a button (from or one of ) until you hear a beep. Type B and C: Each time is pressed, station pages are changed. There are a total of 6 pages.
Page 244 3-2. Using the audio system ■ Displaying text information Press Type A: Each time is pressed, the display changes in the following order: Channel name → Title (song/program title) → Name (artist name/feature) → Channel number. Type B and C: Each time is pressed, the display changes in the fol- lowing order: Title (song/program title) →...
Page 245 3-2. Using the audio system ■ When the battery is disconnected All preset stations are erased. (type A only) ■ Reception sensitivity ● Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.
Page 246 ANTENNA securely. CHECK There is a short-circuit in the antenna or the sur- ANTENNA rounding antenna cable. See a Toyota certified dealer. ® You have not subscribed to XM Satellite Radio. The radio is being updated with the latest encryp- ®...
Page 247 3-2. Using the audio system The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. ® Contact the XM Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 438-9677 (Canada) ■...
Page 248: Using The Cd Player
3-2. Using the audio system Using the CD player Type A Power Volume CD eject Playback Selecting a track Searching playback Fast-forward Reverse Displaying text messages Repeat play Random playback Type B and C Power Volume CD eject CD load Searching playback (type B only)
Page 249 3-2. Using the audio system Loading CDs ■ Loading a CD (type A and C) Insert a CD. ■ Loading a CD (type B) Press STEP When the indicator on the slot turns from amber to green, STEP insert a CD. ■...
Page 250 3-2. Using the audio system Ejecting CDs ■ Ejecting a CD (type A and C) Press and remove the CD. ■ Ejecting a CD (type B) To select the CD to be ejected, press that corre- STEP sponds to “ ”...
Page 251 3-2. Using the audio system Scanning tracks Press STEP The first ten seconds of each track will be played. To cancel, press again. Press again when the desired track is reached. STEP Selecting a CD (type B only) ■ Selecting a CD to play Press that corresponds to “...
Page 252 3-2. Using the audio system Random playback ■ Current CD Press (RAND) or that corresponds to “RDM”. Songs are played in random order. To cancel, press the same button until “OFF” is displayed. ■ All CDs (type B only) Press that corresponds to “RDM”...
Page 253 3-2. Using the audio system Switching the display Press Type A: Each time is pressed, the display changes in the following order: Track no./Elapsed time → CD title → Track name. Type B and C: Each time is pressed, the display changes in the fol- lowing order: Track title →...
Page 254 “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played back. ■ Discs that can be used Discs with the marks shown below can be used.
Page 255 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Discs. Doing so may damage the CD player and/or the CD insert/eject function. ●...
Page 256 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ●...
Page 257: Playing Mp3 And Wma Discs
3-2. Using the audio system Playing MP3 and WMA discs Type A Power Volume Selecting a file CD eject Selecting a folder Playback Selecting a file Reversing Fast-forwarding Searching playback Repeat play Displaying text messages Random playback Type B and C Power Volume Selecting a file...
Page 258 3-2. Using the audio system Loading and ejecting MP3 and WMA discs →P. 224 Selecting MP3 and WMA discs (type B only) →P. 225 Selecting and scanning a folder ■ Selecting folders one at a time Press “∧” or “∨” on to select the desired folder.
Page 259 3-2. Using the audio system ■ Selecting the desired file by cueing the files in the folder Press When the desired file is reached, press once again. Fast-forwarding and reversing files Type A: Press ) or ∧ Type B and C: Press and hold “ ”...
Page 260 3-2. Using the audio system Repeat play ■ Repeating a file Press (RPT) or that corresponds to “RPT”. To cancel, press the same button until “OFF” is displayed. ■ Repeating all of the files in a folder Type A: Press and hold (RPT) until you hear a beep.
Page 261 “WAIT” or “PLEASE WAIT”: Operation has stopped due to a high tempera- ture inside the player. Wait for a while and then press . Contact your Toyota dealer if the CD still cannot be played. ■ Discs that can be used →P.
Page 262 3-2. Using the audio system ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format.
Page 263 3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
Page 264 3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played.
Page 265: Operating An Ipod ® Player
3-2. Using the audio system ® ∗ Operating an iPod player ® Connecting an iPod player enables you to enjoy music from the vehicle speakers. ® ■ Connecting an iPod player Open the cover and connect STEP ® an iPod player using an ®...
Page 266 3-2. Using the audio system Selecting a play mode ® Press that corresponds to “BROWSE” to select iPod STEP menu mode. Press that corresponds to the desired play mode. STEP ■ Play mode list First Second Third Fourth Play mode selection selection selection...
Page 267 3-2. Using the audio system ■ Selecting a list Turn to display the first selection list. STEP Press to select the desired item. STEP Pressing that corresponds to “MORE” changes to the second selection list. Repeat the same procedure to select the desired song name. STEP To return to the previous selection list, press that corresponds...
Page 268 3-2. Using the audio system Selecting songs Turn or press “∧” or “∨” on to select the desired song. Playing and pausing songs Press Fast-forwarding and reversing songs ∧ Press and hold “ ” or “∨” on Shuffle playback ■ Playing songs from one playlist or album in random order Press that corresponds to “RDM”.
Page 269 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ® ■ About iPod ® iPod is registered trademarks of Apple computer, Inc.
Page 270 3-2. Using the audio system ■ Compatible models ® ● iPod 5th generation Version 1.2 or later ® ● iPod nano 3rd generation Version 1.0 or later ® ● iPod nano 2nd generation Version 1.1.2 or later ® ● iPod nano Version 1.2 or later ®...
Page 271: Operating A Usb Memory Player
3-2. Using the audio system ∗ Operating a USB memory player Connecting a USB memory player enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory player Open the cover and connect a STEP USB memory player. Press STEP ■...
Page 272 3-2. Using the audio system Selecting and scanning a folder ■ Selecting a folder Press “∧” or “∨” on to select the desired folder. ■ Returning to the first file of the first folder Press and hold “∨” on until you hear a beep. ■...
Page 273 3-2. Using the audio system Playing and pausing files Press Fast-forwarding and reversing files ∧ Press and hold “ ” or “∨” on Random playback ■ Playing files from a folder in random order Press that corresponds to “RDM”. To cancel, press the button twice. ■...
Page 274 3-2. Using the audio system Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time ■ USB memory player functions Depending on the USB memory player that is connected to the system, cer- tain functions may not be available.
Page 275 3-2. Using the audio system ■ USB memory player ● Compatible device USB memory players that can be used for MP3 and WMA playback. Depending on the type of USB device, playback may not be possible. ● Compatible device formats The following device formats can be used: •...
Page 276 3-2. Using the audio system ● MP3 file compatibility • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III, MPEG2.5) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) MPEG2.5: 8, 11.025, 12 (kHz) •...
Page 277 3-2. Using the audio system ● Extensions If the file extensions .mp3 and .wma are used for files other than MP3 and WMA files, they will be mistakenly recognized and played as MP3 and WMA files. This may result in large amounts of interference and damage to the speakers.
Page 278: Optimal Use Of The Audio System
3-2. Using the audio system Optimal use of the audio system Type A Adjusting the sound quality and ASL Type B and C Adjusting the sound quality Menu button Selector buttons I n f o r ma t i o n P r o v i d e d b y :...
Page 279 3-2. Using the audio system Using the audio control function ■ Changing sound quality modes Type A Pressing selects the mode to be changed in the following order: “BAS”→“TRE”→“FAD”→“BAL”→“ASL” Type B and C Press STEP Press that corresponds to the desired mode. STEP “BASS”, “MID”...
Page 280 3-2. Using the audio system Type B and C Mode Sound qual- Turn to the Turn to the Level displayed ity mode left right BASS Bass* -5 to 5 Mid-range* -5 to 5 High (type B only) TREB Treble* -5 to 5 Front/rear Shifts to FADE...
Page 281 3-2. Using the audio system Type B and C Press STEP Press that corresponds to “MORE”. STEP Press that corresponds to “ASL”. STEP Press that corresponds to the desired mode. STEP Type B: “ON” or “OFF” Type C: “LOW”, “MID”, “HIGH”, or “OFF” ASL automatically adjusts the volume and tone quality according to vehi- cle speed.
Page 282 3-2. Using the audio system ■ Trademark owned by SRS Labs, Inc. (type A only) ® ® The audio systems utilize SRS FOCUS and SRS TruBass audio enhancement technologies, under license from SRS Labs, Inc., in all modes except AM radio mode. FOCUS, TruBass, SRS and symbols are trademarks of SRS Labs, Inc.
Page 283: Using The Aux Adapter
3-2. Using the audio system Using the AUX adapter This adapter can be used to connect a portable audio device and lis- ten to it through the vehicle’s speakers. Open the cover and connect the portable audio device. STEP Type A Type B Press STEP...
Page 284 3-2. Using the audio system ■ Operating portable audio devices connected to the audio system The volume can be adjusted using the vehicle's audio controls. All other adjustments must be made on the portable audio device itself. ■ When using a portable audio device connected to the power outlet Noise may occur during playback.
Page 285: Using The Steering Wheel Audio Switches
3-2. Using the audio system Using the steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. 4-spoke steering wheel Increases/decreases vol- Radio mode: Select radio stations CD mode: Select tracks, files (MP3 and WMA) and discs ®...
Page 286 3-2. Using the audio system Turning the power on Press when the audio system is turned off. The audio system can be turned off by holding the switch down until you hear a beep. Changing the audio source Press when the audio system is turned on. The audio source changes as follows each time the switch is pressed.
Page 287 3-2. Using the audio system Selecting a track/file or folder ® Press to select the CD, iPod player or USB STEP memory player mode. Press “∨” or “∧” on to select the desired STEP track/file or folder. Selecting a folder Press to select the MP3 and WMA mode.
Page 288: Using The Bluetooth
® 3-3. Using the Bluetooth audio system ® ∗ Bluetooth audio system ® The Bluetooth audio system enables you to enjoy music played on a portable digital audio player (portable player) from the vehicle speakers via wireless communication. ® This audio system supports Bluetooth , a wireless data system capable of playing portable audio music without cables.
Page 289 ® 3-3. Using the Bluetooth audio system ■ When transferring ownership of the vehicle Be sure to initialize the system to prevent personal data from being improp- erly accessed. (→P. 303) ® ■ About Bluetooth Bluetooth is a registered trademark of Bluetooth SIG.
Page 290 ® 3-3. Using the Bluetooth audio system CAUTION ■ FCC WARNING Changes or modifications in construction not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radio frequency exposure. This device is approved for Mobile Application only and, to comply with applicable FCC radio frequency exposure regula- tions, must be used with a distance of at least 7.9 in.
Page 291: Using The Bluetooth ® Audio System
® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system ■ Audio unit Display A message, name, number, etc. is displayed. Lower-case characters and special characters cannot be displayed. Displays information that is too long to be displayed at one time on the display (press and hold) Selects items such as menu...
Page 292 ® 3-3. Using the Bluetooth audio system Operating the system using voice commands By following voice guidance instructions output from the speaker, ® audio sys- voice commands enable to the operation of the Bluetooth tem without the need to check the display or operate ■...
Page 293 ® 3-3. Using the Bluetooth audio system ® Using the Bluetooth audio system for the first time ® Before using the Bluetooth audio system, it is necessary to register ® a Bluetooth enabled portable player in the system. Follow the proce- dure below to register (pair) a portable player: Press until “BT AUDIO”...
Page 294 ® 3-3. Using the Bluetooth audio system ® If the portable player has a Bluetooth phone, the phone can be reg- istered at the same time. (→P. 286) ® Menu list of the Bluetooth audio system ■ Normal operation Second First menu Third menu Operation detail...
Page 295 ® 3-3. Using the Bluetooth audio system ■ When using a voice command For numbers, say a combination of single digits from zero to nine. Say the command correctly and clearly. ■ Situations that the system may not recognize your voice ●...
Page 296: Operating A Bluetooth
® 3-3. Using the Bluetooth audio system ® Operating a Bluetooth enabled portable player Power Volume Selector knob Fast- forwarding Selecting tracks reversing Playback Playback/pause Displaying text messages Selecting an album Press “∨” or “∧” on Selecting tracks Press “∧” or “∨” on Playing and pausing tracks Press I n f o r ma t i o n P r o v i d e d b y :...
Page 297 ® 3-3. Using the Bluetooth audio system Fast-forwarding and reversing tracks ∧ Press and hold “ ” or “∨” on Switching the display Press Each time is pressed, the display changes in the following order: Track title → Track title/Artist name → Track title/Album name → Track title/Elapsed time Using the steering wheel audio switches →P.
Page 298: Setting Up A Bluetooth ® Enabled Portable Player
® 3-3. Using the Bluetooth audio system ® Setting up a Bluetooth enabled portable player ® Registering a portable player in the Bluetooth audio system allows the system to function. The following functions can be used for reg- istered portable players: ■...
Page 299 ® 3-3. Using the Bluetooth audio system Registering a portable player Select “Pair Audio Player” using a voice command or , and perform the procedure for registering a portable player. (→P. 268) Selecting a portable player to be used Select “Select Audio Player” using a voice command or STEP Select the portable player to be used by either of the following STEP...
Page 300 ® 3-3. Using the Bluetooth audio system Press the talk switch and say “From Car” or “From Audio”, and STEP select “Confirm” by using a voice command or Vehicles with smart key system: If “From Car” is selected, the porta- ble player will be automatically connected whenever the “ENGINE START STOP”...
Page 301 ® 3-3. Using the Bluetooth audio system Listing the registered portable players Select “List Audio Players” using a voice command or . The list of registered portable players will be read aloud. When listing is complete, the system returns to “BT•A Setup”. Pressing the talk switch while the name of a portable player is being read aloud selects the portable player, and the following functions will become available:...
Page 302 ® 3-3. Using the Bluetooth audio system Deleting a registered portable player Select “Delete Audio Player (Delete Audio)” using a voice STEP command or Select the portable player to be deleted by either of the follow- STEP ing methods and select “Confirm” using a voice command or a.
Page 303: Bluetooth Audio System Setup
® 3-3. Using the Bluetooth audio system ® Bluetooth audio system setup ■ System setup items and operation procedures →P. 301 I n f o r ma t i o n P r o v i d e d b y :...
Page 304: Using The Hands-Free Phone System (For Cellular Phone)
3-4. Using the hands-free phone system (for cellular phone) ∗ Hands-free phone system (for cellular phone) features ® This system supports Bluetooth , which allows you to make or receive calls without using cables to connect a cellular phone and the system, and without operating the cellular phone.
Page 305 3-4. Using the hands-free phone system (for cellular phone) Title Page Using the hands-free phone system ■ Operating the system by using a voice command ■ Using the hands-free phone system for P. 283 the first time ■ Menu list of the hands-free phone system Making a phone call ■...
Page 306 3-4. Using the hands-free phone system (for cellular phone) ■ Conditions affecting operation The hands-free phone system may not operate normally in the following situ- ations: ● The cellular phone is turned off, or located outside the service area. ● The cellular phone has a low battery.
Page 307 3-4. Using the hands-free phone system (for cellular phone) ■ Certification for the hands-free phone system Type B FCC ID: BABFT0001A IC ID: 2024B-FT0001A MADE IN JAPAN Type C FCC ID: ACJ932C5ZZZ035 IC ID: 216J-C5ZZZ035 MADE IN JAPAN This device complies with Part 15 of the FCC Rules and RSS-210 Rules. Operation is subject to the following two conditions;...
Page 308: Using The Hands-Free Phone System (For Cellular Phone)
3-4. Using the hands-free phone system (for cellular phone) Using the hands-free phone system (for cellular phone) ■ Audio unit Display A message, name, phone number, etc. is displayed. Lower-case characters and special characters, such as an umlaut, cannot be dis- played.
Page 309 3-4. Using the hands-free phone system (for cellular phone) ■ Steering wheel 4-spoke steering wheel Volume The voice guidance volume cannot be adjusted using this button. On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Off-hook switch Turns the hands-free sys- tem on/starts a call Talk switch...
Page 310 3-4. Using the hands-free phone system (for cellular phone) 3-spoke steering wheel Volume The voice guidance volume cannot be adjusted using this button. Off-hook switch Turns the hands-free sys- tem on/starts a call On-hook switch Turns the hands-free sys- tem off/ends a call/refuses a call Talk switch Turns the voice command...
Page 311 3-4. Using the hands-free phone system (for cellular phone) Operating the system by using a voice command By following voice guidance instructions output from the speaker, voice commands enable to the operation of the hands-free phone system without the need to check the display or operate ■...
Page 312 3-4. Using the hands-free phone system (for cellular phone) Select “Pair Phone” using a voice command or STEP Register a phone name by either of the following methods. STEP a. Select “Record Name” by using , and say a name to be registered.
Page 313 3-4. Using the hands-free phone system (for cellular phone) Menu list of the hands-free phone system ■ Normal operation Second First menu Third menu Operation detail menu Dialing a number stored in Callback the incoming call history memory Dialing a number stored in Redial the outgoing call history memory...
Page 314 3-4. Using the hands-free phone system (for cellular phone) Second First menu Third menu Operation detail menu Set PIN Setting a PIN code Phonebook Lock Locking the phone book Security Phonebook Unlocking the phone book Unlock Registering the cellular Pair Phone phone to be used Changing a registered name Change Name...
Page 315 3-4. Using the hands-free phone system (for cellular phone) ■ Using a short cut key First menu Second menu Operation detail Dialing a number registered Dial “XXX (name)” in the phone book Dial “XXX (number)” Dialing the input numbers Phone book add Adding a new number entry Changing the name of a...
Page 316 3-4. Using the hands-free phone system (for cellular phone) ■ Automatic volume adjustment When vehicle speed is 50 mph (80 km/h) or more, the volume automatically increases. The volume returns to the previous volume setting when vehicle speed drops to 43 mph (70 km/h) or less. ■...
Page 317: Making A Phone Call
3-4. Using the hands-free phone system (for cellular phone) Making a phone call ■ Making a phone call ● Dialing by inputting a number “Dial by number” ● Dialing by inputting a name “Dial by name” ● Speed dialing ● Dialing a number stored in the outgoing history memory “Redial”...
Page 318 3-4. Using the hands-free phone system (for cellular phone) Dialing by inputting a name Press the talk switch and say “Dial by name”. STEP Select a registered name to be input by either of the following STEP methods: a. Press the talk switch and say a registered name. b.
Page 319 3-4. Using the hands-free phone system (for cellular phone) Transferring a call A call can be transferred between the cellular phone and system while dialing, receiving a call, or during a call. Use one of the follow- ing methods: a. Operate the cellular phone. Refer to the manual that comes with the cellular phone for the oper- ation of the phone.
Page 320 3-4. Using the hands-free phone system (for cellular phone) The following operations can be performed: Dialing: Press the off-hook switch or select “Dial” by using a voice command or Storing the number in the phone book: Select “Store” by using a voice command or Deleting: Select “Delete”...
Page 321: Setting A Cellular Phone
3-4. Using the hands-free phone system (for cellular phone) Setting a cellular phone Registering a cellular phone in the hands-free phone system allows the system to function. The following functions can be used for reg- istered cellular phones: ■ Functions and operation procedures To enter the menu for each function, follow the steps below by using a voice command or ●...
Page 322 3-4. Using the hands-free phone system (for cellular phone) Selecting the cellular phone to be used Select “Select Phone” by using a voice command or STEP Pattern A Select the cellular phone to be used by either of the following STEP methods, and select “Confirm”...
Page 323 3-4. Using the hands-free phone system (for cellular phone) c. Select the desired phone name by using Press the talk switch or select “Record Name” by using STEP and say a new name. Select “Confirm” by using a voice command or STEP Listing the registered cellular phones Selecting “List Phones”...
Page 324 3-4. Using the hands-free phone system (for cellular phone) Deleting a cellular phone Select “Delete Phone” by using a voice command or STEP Select the cellular phone to be deleted by either of the follow- STEP ing methods and select “Confirm” by using a voice command a.
Page 325 3-4. Using the hands-free phone system (for cellular phone) Turning the hands-free phone automatic connection on/off ■ Turning off the automatic connection Select “Handsfree Power” by using a voice command or STEP Select “Turn off” by using a voice command or STEP ■...
Page 326: Security And System Setup
3-4. Using the hands-free phone system (for cellular phone) Security and system setup To enter the menu of each setting, follow the steps below: ■ Security setting items and operation procedure ● Setting or changing the PIN (Personal Identification Number) 1.
Page 327 3-4. Using the hands-free phone system (for cellular phone) ■ Changing the PIN Select “Set PIN” by using a voice command or STEP Enter the registered PIN by using a voice command or STEP Enter a new PIN by using a voice command or STEP When using , input the code 1 digit at a time.
Page 328 3-4. Using the hands-free phone system (for cellular phone) Setting voice guidance volume Select “Guidance Volume” by using STEP Change the voice guidance volume. STEP To decrease the volume: Turn counterclockwise. To increase the volume: Turn clockwise. Initialization Select “Initialize” and then “Confirm” by using STEP Select “Confirm”...
Page 329 3-4. Using the hands-free phone system (for cellular phone) ■ Initialization ● The following data in the system can be initialized: • Phone book • Outgoing and incoming call history • Speed dials • Registered cellular phone data • Security code ●...
Page 330: Using The Phone Book
3-4. Using the hands-free phone system (for cellular phone) Using the phone book To enter the menu of each setting, follow the steps below: ● Adding a new phone number 1. “Phonebook” → 2. “Add Entry” ● Setting speed dial 1.
Page 331 3-4. Using the hands-free phone system (for cellular phone) ■ Adding procedure Select “Add Entry” by using a voice command or STEP Use one of the following methods to input a telephone num- STEP ber: Inputting a telephone number by using a voice command STEP2-1 Select “By Voice”...
Page 332 3-4. Using the hands-free phone system (for cellular phone) Inputting a phone number by using STEP2-1 Select “Manual Input” by using STEP2-2 Input a phone number by using , and press once again. Input the phone number 1 digit at a time. Selecting a phone number from outgoing or incoming call history STEP2-1 Select “Call History”...
Page 333 3-4. Using the hands-free phone system (for cellular phone) Select the name to be registered by either of the following STEP methods, and select “Confirm” by using a voice command or a. Press the talk switch and say the desired name. b.
Page 334 3-4. Using the hands-free phone system (for cellular phone) Setting speed dials Select “Set Speed Dial (Speed Dial)” by using a voice com- STEP mand or Select the data to be registered as a speed dial by either of STEP the following methods: a.
Page 335 3-4. Using the hands-free phone system (for cellular phone) Changing a registered name Select “Change Name” by using a voice command or STEP Select the name to be changed by either of the following STEP methods. a. Press the talk switch, say desired name, and select “Con- firm”...
Page 336 3-4. Using the hands-free phone system (for cellular phone) Deleting registered data Select “Delete Entry” by using a voice command or STEP Select the data to be deleted by either of the following meth- STEP ods, and select “Confirm” by using a voice command or a.
Page 337 3-4. Using the hands-free phone system (for cellular phone) Listing the registered data Selecting “List names” by using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following function will be available.
Page 338: 3-5. Using The Interior Lights
3-5. Using the interior lights Interior lights list Personal lights (→P. 315) Interior light (→P. 314) Engine switch light (vehicles without smart key system) Front door courtesy light I n f o r ma t i o n P r o v i d e d b y :...
Page 339: Interior Light
“DOOR” position, the lights will go off automatically after 20 minutes. ■ Customization that can be configured at Toyota dealer Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 510)
Page 340: Personal Lights
3-5. Using the interior lights Interior light and personal lights Vehicles with moon roof “DOOR” position Personal lights Front On/off Rear (vehicles with moon roof) On/off When either of the rear side doors is opened, the light on that side turns on automatically. Clos- ing the rear side doors will turn the lights off.
Page 341: 3-6. Using The Storage Features
3-6. Using the storage features List of storage features Auxiliary boxes Glove box Cup holders Console box I n f o r ma t i o n P r o v i d e d b y :...
Page 342: Glove Box
3-6. Using the storage features Glove box and console box Glove box Open (pull the lever) Lock with the master key (vehicles without smart key system) or mechanical key (vehicles with smart key sys- tem) Unlock with the master key (vehicles without smart key system) or mechanical key (vehicles with smart key sys-...
Page 343 3-6. Using the storage features Console box ■ When using the console box lid as an armrest (if equipped) If necessary, the console box lid can slide forward. Pull the lid forward by grasping the front of the lid. ■ Tray in the rear console box The tray slides forward/backward and can be removed.
Page 344: Cup Holders
3-6. Using the storage features Cup holders Cup holders Manual transmission Lift the lid. Automatic transmission (type A) Lift the lid. Automatic transmission (type B) Push the lid. I n f o r ma t i o n P r o v i d e d b y :...
Page 345 3-6. Using the storage features Cup holders Rear (type A) Pull the armrest down. Rear (type B) Pull the armrest down and lift the lid. ■ Using the cup holder (front) to store small items (automatic transmis- sion) Remove the holder. I n f o r ma t i o n P r o v i d e d b y :...
Page 346: Auxiliary Boxes
3-6. Using the storage features Cup holders and auxiliary boxes CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.
Page 347 3-6. Using the storage features Auxiliary boxes Front console Push the lid. Center console (type A) Push the lid. Center console (type B) Lift the lid. I n f o r ma t i o n P r o v i d e d b y :...
Page 348 3-6. Using the storage features Auxiliary boxes ■ Cable pass-through The auxiliary box of the front console is provided with a hole that allows cables to be passed into the cabin from the power outlet and AUX or USB/AUX adapter inside.
Page 349: 3-7. Other Interior Features
3-7. Other interior features Sun visors Forward position: Flip down. Side position: Flip down, unhook, and swing to the side. I n f o r ma t i o n P r o v i d e d b y :...
Page 350: Vanity Mirrors
3-7. Other interior features Vanity mirrors Slide the cover. The light turns on when the cover is opened. (if equipped) I n f o r ma t i o n P r o v i d e d b y :...
Page 351: Clock
3-7. Other interior features Clock Adjusts the hour. Adjusts the minutes. ■ The clock is displayed when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. I n f o r ma t i o n P r o v i d e d b y :...
Page 352: Ashtray
3-7. Other interior features ∗ Ashtray An ashtray can be installed in a cup holder. (→P. 319) CAUTION ■ When not in use Keep the ashtray closed. Injuries may result in the event of sudden braking, sudden swerving or an accident.
Page 353: Power Outlets
3-7. Other interior features Power outlets The power outlet can be used for 12 V accessories that run on less than 10 A. Front console Center console (if equipped) I n f o r ma t i o n P r o v i d e d b y :...
Page 354 3-7. Other interior features ■ The power outlet can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position. ■...
Page 355: Seat Heaters
3-7. Other interior features ∗ Seat heaters Heats the driver’s seat Heats the passenger’s seat The indicator light comes on. ■ The seat heaters can be used when Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON”...
Page 356 3-7. Other interior features NOTICE ■ To prevent seat heater damage Do not put unevenly weighted objects on the seat and do not stick sharp objects (needles, nails, etc.) into the seat. ■ To prevent battery discharge Turn the switches off when the engine is not running. I n f o r ma t i o n P r o v i d e d b y :...
Page 357: Armrest
3-7. Other interior features Armrest Pull the armrest down for use. NOTICE ■ To prevent damage to the armrest Do not place too much strain on the armrest. I n f o r ma t i o n P r o v i d e d b y :...
Page 358: Rear Sunshade
3-7. Other interior features ∗ Rear sunshade Pull the tab of the shade and hook it on using the anchors. To lower the shade, pull the tab slightly to unhook the shade, and lower it slowly. CAUTION ■ When the rear sunshade is being raised or lowered Do not place fingers or other objects in the fastener section or in the open- ing.
Page 359: Trunk Storage Extension
3-7. Other interior features Trunk storage extension Long objects can be loaded in the vehicle by utilizing the trunk space and rear seat area. Pull down the armrest. STEP Open the armrest door. STEP The armrest door can be locked and unlocked using the mechanical key (vehicles with smart key system) or master key (vehicles without smart...
Page 360: Floor Mat
3-7. Other interior features Floor mat Securely place a mat that matches the size of the space on the car- pet. Secure the driver's floor mat using the hooks provided. CAUTION ■ When inserting the floor mat Observe the following precautions. Failure to do so may result in the floor mat slipping and interfering with the movement of the pedals during driving, resulting in an accident.
Page 361: Trunk Features
3-7. Other interior features Trunk features ■ Storage box ■ Grocery bag hooks Type A Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 362 3-7. Other interior features ■ Cargo net (if equipped) Type A Type B NOTICE ■ To prevent damage to the cargo net hooks Avoid hanging things other than a cargo net on them. I n f o r ma t i o n P r o v i d e d b y :...
Page 363: Garage Door Opener
3-7. Other interior features ∗ Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices. ® The garage door opener (HomeLink Universal Transceiver) is manufac- ®...
Page 364 3-7. Other interior features ® ■ Programming HomeLink Point the remote control for the STEP device 1 to 3 in. (25 to 75 mm) ® from the HomeLink control but- tons. Keep indicator light ® HomeLink in view while pro- gramming.
Page 365 3-7. Other interior features Repeat the steps above to program another device for each of STEP ® the remaining HomeLink buttons. ■ Programming a Rolling Code system (for U.S. owners) If your device is Rolling Code equipped, follow the steps under the ®...
Page 366 ® the remaining HomeLink buttons. ■ Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. ■ Reprogramming a button ® The individual HomeLink buttons cannot be erased but can be reprogrammed.
Page 367 3-7. Other interior features ■ Before programming ● Install a new battery in the transmitter. ● The battery side of the transmitter must be pointed away from ® HomeLink ■ Certification for the garage door opener This device complies with Part 15 of the FCC Rules and with RSS-210 of the IC Rules.
Page 368: Compass
3-7. Other interior features ∗ Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation To turn the compass on or off, press and hold “AUTO” for 3 seconds. ■ Displays and directions Display Direction...
Page 369 3-7. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in the illustration, the compass will deviate.
Page 370 3-7. Other interior features ■ Circling calibration Stop the vehicle in a place where it is safe to drive in a circle. STEP Press and hold “AUTO” for 9 STEP seconds. C appears on the compass dis- play. Drive the vehicle at 5 mph (8 km/ STEP h) or less in a circle until a direc- tion is displayed.
Page 371 3-7. Other interior features CAUTION ■ While driving the vehicle Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped. ■ When doing the circling calibration Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood.
Page 372: 4-1. Maintenance And Care
4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 373 4-1. Maintenance and care ■ To prevent deterioration and body corrosion ● Wash the vehicle immediately in the following cases: • After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface •...
Page 374: 4-1. Maintenance And Care
4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
Page 375 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 376 4-1. Maintenance and care NOTICE ■ Cleaning detergents Do not use organic substances such as benzene or gasoline, acidic or alka- line solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces. ■...
Page 377: 4-2. Maintenance
It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 378 4-2. Maintenance ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
Page 379: General Maintenance
Booklet” “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items Check points Check the connections. Battery (→P.
Page 380: Vehicle Interior
4-2. Maintenance Vehicle interior Items Check points • Moves smoothly (without uneven Accelerator pedal pedal effort or catching)? • Can the vehicle be held securely Automatic transmission “Park” on an incline with the shift lever in mechanism • Moves smoothly? •...
Page 381: Vehicle Exterior
4-2. Maintenance Vehicle exterior Items Check points Door/trunk • Operate smoothly? Engine hood • The lock system works properly? • Is there any leakage after park- Fluid leaks ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? Tires •...
Page 382: Emission Inspection And Maintenance (I/M) Programs
If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
Page 383: 4-3. Do-It-Yourself Maintenance
Brake fluid level (→P. 375) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology.
Page 384 4-3. Do-it-yourself maintenance Items Parts and tools Fuse with same amperage rating Fuses (→P. 405) as original Bulb with same number and watt- Light bulbs (→P. 418) age rating as original • Automatic transmission fluid ® DEXRON II or III Power steering fluid •...
Page 385 4-3. Do-it-yourself maintenance CAUTION ● Do not smoke, cause sparks or expose an open flame to fuel or the bat- tery. Fuel and battery fumes are flammable. ● Be extremely cautious when working on the battery. It contains poisonous and corrosive sulfuric acid. ●...
Page 386: Hood
4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP The hood will pop up slightly. Lift the auxiliary catch lever STEP and lift the hood. CAUTION ■...
Page 387: Positioning A Floor Jack
4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. ■ Front ■ Rear Type A Type B I n f o r ma t i o n P r o v i d e d b y :...
Page 388 4-3. Do-it-yourself maintenance CAUTION ■ When raising your vehicle Make sure to observe the following to reduce the possibility of death or seri- ous injury: ● Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
Page 389: Engine Compartment
4-3. Do-it-yourself maintenance Engine compartment 2.5 L 4-cylinder (2AR-FE) engine Power steering fluid Fuse box (→P. 405) reservoir (→P. 376) Battery (→P. 378) Engine oil filler cap Radiator (→P. 374) (→P. 370) Electric cooling fans Engine oil level dipstick Condenser (→P.
Page 390 4-3. Do-it-yourself maintenance 3.5 L V6 (2GR-FE) engine Power steering fluid Fuse box (→P. 405) reservoir (→P. 376) Battery (→P. 378) Engine oil filler cap Radiator (→P. 374) (→P. 370) Electric cooling fans Engine oil level dipstick Condenser (→P. 374) (→P.
Page 391 4-3. Do-it-yourself maintenance Engine compartment cover (3.5 L V6 [2GR-FE] engine) ■ Removing the engine compartment cover ■ Installing the clips I n f o r ma t i o n P r o v i d e d b y :...
Page 392 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil Park the vehicle on level ground. After turning off the engine, STEP wait more than five minutes for the oil to drain back into the bottom of the engine.
Page 393 4-3. Do-it-yourself maintenance Wipe the dipstick and reinsert it fully. STEP 2.5 L 4-cylinder (2AR-FE) engine Full 3.5 L V6 (2GR-FE) engine Full I n f o r ma t i o n P r o v i d e d b y :...
Page 394 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 395 1000 km) ● If you consume more than 1.1 qt. (1.0 L, 0.9 Imp. qt.) every 600 miles (1000 km), contact your Toyota dealer. ■ After changing the engine oil (U.S.A. only) To reset the oil change system, follow the procedure below: STEP Turn the “ENGINE START STOP”...
Page 396 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
Page 397: Engine Coolant
If the coolant level drops within a short time after replenishing Visually check the radiator, hoses, engine coolant filler cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. ■...
Page 398 Radiator and condenser Check the radiator and condenser and remove any foreign objects. If any of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer. CAUTION ■...
Page 399 4-3. Do-it-yourself maintenance Brake fluid ■ Checking fluid level The brake fluid level should be between the “MAX” and “MIN” lines on the tank. Make sure to check the fluid type and prepare the necessary items. ■ Adding fluid Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Items Clean funnel...
Page 400 4-3. Do-it-yourself maintenance NOTICE ■ If the fluid level is low or high It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.
Page 401 4-3. Do-it-yourself maintenance ■ Checking the fluid level Make sure to check the fluid type and prepare the necessary items. ® Fluid type Automatic transmission fluid DEXRON II or III Rag or paper towel and funnel (only for adding Items fluid) Clean all dirt off the reservoir.
Page 402 Type A Blue: Good condition White: Charging is necessary. Have the vehicle inspected by your Toyota dealer. Red: Not working properly. Have the battery checked by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 403 If the engine will not start even after multiple attempts at the above method, contact your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 404 4-3. Do-it-yourself maintenance CAUTION ■ Chemicals in the battery A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: ●...
Page 405 4-3. Do-it-yourself maintenance NOTICE ■ When recharging the battery Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. Washer fluid Add washer fluid in the following situations. ● Any washer does not work. ●...
Page 406: Tires
Tire rotation Vehicles with a compact spare tire Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is Front carried out at the same inter- val as tire inspection.
Page 407 ■ The tire pressure warning system (U.S.A. only) Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 435) Vehicles with compact spare tire: The compact spare tire is not equipped with the tire pressure warning valve and transmitters.
Page 408 Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 385) Initializing the tire pressure warning system ■...
Page 409 ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 410 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
Page 411 Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings has not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●...
Page 412 4-3. Do-it-yourself maintenance ■ Tire types 1 Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 413 4-3. Do-it-yourself maintenance ■ Tire pressure warning system certification FCC ID: PAXPMV107J FCC ID: HYQ13BCX IC ID: 3729A-PMV107J IC ID: 1551A-13BCX For vehicles sold in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 414 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 415 Repairing or replacing tires, wheels and tire pressure warning valves and transmitters When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. ■...
Page 416: Tire Inflation Pressure
4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 491) One of the following labels will be attached to the driver’s side center pillar.
Page 417 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge Remove the tire valve cap. STEP Press the tip of the tire pressure gauge onto the tire valve. STEP Read the pressure using the graduations of the gauge. STEP If the tire inflation pressure is not at the recommended level STEP...
Page 418 Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
Page 419 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ● Excessive wear ● Uneven wear ●...
Page 420: Wheels
● Bent wheels that have been straightened ■ Aluminum wheel precautions ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 421 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 422: Air Conditioning Filter
4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. ■ Removal method Vehicles with smart key system: Turn the “ENGINE START STEP STOP” switch OFF. Vehicles without smart key system: Turn the engine switch OFF.
Page 423 2 minutes at 72 psi (500 kPa, 5.0 kgf/cm bar). If it is not available, have the filter cleaned by your Toyota dealer. ■ Replacement method Remove the air conditioning filter and replace it with a new one.
Page 424 4-3. Do-it-yourself maintenance NOTICE ■ To prevent damage to the system ● When using the air conditioning system, make sure that a filter is always installed. ● When cleaning the filter, do not clean the filter with water. I n f o r ma t i o n P r o v i d e d b y :...
Page 425: Key Battery
4-3. Do-it-yourself maintenance Key battery Replace the battery with a new one if it is discharged. ■ You will need the following items: ● Flathead screwdriver (To prevent damage to the key, cover the tip of the screwdriver with rag.) ●...
Page 426 4-3. Do-it-yourself maintenance Remove the depleted battery. STEP Insert a new battery with the “+” terminal facing up. Vehicles without smart key system Remove the cover. STEP Remove the module. STEP I n f o r ma t i o n P r o v i d e d b y :...
Page 427 Use a CR1632 (vehicles with smart key system), or CR2016 (vehicles without smart key system) lithium battery ● Batteries can be purchased at your Toyota dealer, jewelers, or camera stores. ● Replace only with the same or equivalent type recommended by your Toyota dealer.
Page 428 4-3. Do-it-yourself maintenance NOTICE ■ For normal operation after replacing the battery Observe the following precautions to prevent accidents. ● Always work with dry hands. Moisture may cause the battery to rust. ● Do not touch or move any other components inside the remote control. ●...
Page 429: Checking And Replacing Fuses
4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Vehicles with smart key system: Turn the “ENGINE START STEP STOP”...
Page 430 4-3. Do-it-yourself maintenance Take out the pullout tool. STEP Only type A fuse can be removed using the pullout tool. Check if the fuse has blown. STEP Type A Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.
Page 431 4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact your Toyota dealer. Fuse layout and amperage ratings ■ Engine compartment (fuse box cover) I n f o r ma t i o n P r o v i d e d b y :...
Page 432 4-3. Do-it-yourself maintenance ■ Engine compartment (fuse block) 2.5 L 4-cylinder (2AR-FE) engine Fuse Ampere Circuit SPARE 30 A Spare fuse SPARE 15 A Spare fuse SPARE 10 A Spare fuse 30 A No circuit RDI FAN 40 A Electric cooling fans CDS FAN 40 A Electric cooling fans...
Page 433 4-3. Do-it-yourself maintenance Fuse Ampere Circuit RR FOG 10 A No circuit Starting system, GAUGE NO.2, ST/AM2 30 A IGN, INJ RR FOG, FR DEF, HTR, ABS NO.1, ABS NO.2, RR DEF, RR PWR SEAT, H-LP CLN, CDS FAN, RDI FAN, MSB, TAIL, PANEL, FR FOG, CIG, RADIO No.2, ECU- ACC, PWR OUTLET, GAUGE 120 A...
Page 434 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Multiport fuel injection system/ sequential multiport fuel injection EFI MAIN 30 A system, EFI NO.2, EFI NO.3, main body ECU 25 A Audio system DOOR NO.1 25 A Main body ECU RADIO NO.1 15 A Audio system, navigation system Wireless remote control system, ECU-B NO.1...
Page 435 4-3. Do-it-yourself maintenance 3.5 L V6 (2GR-FE) engine Fuse Ampere Circuit SPARE 30 A Spare fuse SPARE 15 A Spare fuse SPARE 10 A Spare fuse 30 A No circuit H-LP CLN 30 A No circuit RR PWR SEAT 30 A No circuit RR DEF 50 A...
Page 436 4-3. Do-it-yourself maintenance Fuse Ampere Circuit RR FOG, FR DEF, HTR, ABS NO.1, FAN MAIN, ABS NO.2, RR DEF, RR PWR SEAT, H- LP CLN, CDS FAN, RDI FAN, MSB, TAIL, PANEL, FR FOG, CIG, RADIO No.2, ECU-ACC, PWR OUTLET, 120 A GAUGE No.1, ECU IG No.1, ECU IG No.2, H-LP LVL, WASH, A/C...
Page 437 4-3. Do-it-yourself maintenance Fuse Ampere Circuit Wireless remote control system, ECU-B NO.1 10 A front passenger occupant classifi- cation system, main body ECU Gauges and meters, vanity lights, trunk light, engine switch light, door DOME 10 A courtesy lights, interior light, per- sonal lights, clock, smart key sys- H-LP(LH) 15 A...
Page 438 4-3. Do-it-yourself maintenance ■ Under the instrument panel Fuse Ampere Circuit RR DOOR RH 25 A Rear right power window RR DOOR LH 25 A Rear left power window FUEL OPN 7.5 A No circuit FR FOG 15 A Front fog lights 7.5 A On-board diagnosis system ECU-B NO.2...
Page 439 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 25 A Power windows DOOR NO.2 25 A Main body ECU S/ROOF 30 A Moon roof Front side marker/parking lights, stop/tail lights, rear side marker TAIL 15 A lights, license plate lights, back-up lights, front turn signal lights, main body ECU Navigation system, seat heaters, emergency flashers, air condition-...
Page 440 (→P. 418) ● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. ■ If there is an overload in the circuits The fuses are designed to blow before the entire wiring harness is damaged.
Page 441 Never use a fuse of a higher amperage rating than indicated, or use any other object in place of a fuse. ● Always use a genuine Toyota fuse or equivalent. Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.
Page 442: Light Bulbs
You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 443 4-3. Do-it-yourself maintenance Replacing light bulbs ■ Headlights Turn the bulb base counterclock- STEP wise. Headlight (low beam) Headlight (high beam) Unplug connector while STEP depressing the lock release. Headlight (low beam) Headlight (high beam) ■ Rear turn signal lights Open the trunk lid and remove STEP the cover.
Page 444 STEP ■ Lights other than the above If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. ● Front fog lights (if equipped) ● Front turn signal lights ● Stop/tail lights ● High mounted stoplight ●...
Page 445 LED stop/tail lights and high mounted stoplight The stop/tail lights and high mounted stoplight consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. CAUTION ■...
Page 446 4-3. Do-it-yourself maintenance I n f o r ma t i o n P r o v i d e d b y :...
Page 447: 5-1. Essential Information
5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE ■ To prevent battery discharge Do not leave the emergency flashers on longer than necessary when the engine is not running.
Page 448: If Your Vehicle Needs To Be Towed
If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
Page 449 5-1. Essential information Towing with a sling-type truck NOTICE ■ To prevent body damage Do not tow with a sling-type truck, either from the front or rear. Towing with a wheel-lift type truck from the front Release the parking brake. NOTICE ■...
Page 450 5-1. Essential information Towing with a wheel-lift type truck from the rear Automatic transmission: Use a towing dolly under the front wheels. Manual transmissions: We rec- ommend to use a towing dolly under the front wheels. When not using a towing dolly, turn the engine switch to the “ACC”...
Page 451: If You Think Something Is Wrong
5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
Page 452: Fuel Pump Shut Off System
5-1. Essential information Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 453: Event Data Recorder
5-1. Essential information Event data recorder Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.
Page 454 5-1. Essential information Disclosure of the data Toyota will not disclose the data recorded in an EDR to a third party except when: ● An agreement from the vehicle's owner (or the leasing company for a leased vehicle) is obtained ●...
Page 455: 5-2. Steps To Take In An Emergency
Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning light Warning light/Details Brake system warning light (warning buzzer)* •...
Page 456 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning light Warning light/Details Malfunction indicator lamp Indicates a malfunction in: (U.S.A.)
Page 457 If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible. I n f o r ma t i o n P r o v i d e d b y :...
Page 458 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning light Warning light/Details Correction procedure Open door warning light Check that all doors and the (warning buzzer) Indicates that a door or the trunk are closed.
Page 459 (U.S.A. only) When the light comes on after blinking for 1 minute: Have the system checked Malfunction in the tire by your Toyota dealer. pressure warning system. Master warning light (vehicles with multi-infor- mation display) A buzzer sounds and the →P.
Page 460 5-2. Steps to take in an emergency : Open door warning buzzer: The open door warning buzzer sounds to alert the driver that one or more of the doors or trunk is not fully closed (with the vehicle having reached a speed of 3 mph [5 km/h]).
Page 461 5-2. Steps to take in an emergency Follow the correction procedures. (vehicles with smart key system) After taking the specified steps to correct the suspected problem, check that the warning light turns off. Interior Exterior Warning Correction Warning light/Details light procedure buzzer buzzer...
Page 462 5-2. Steps to take in an emergency Interior Exterior Warning Correction Warning light/Details light procedure buzzer buzzer Smart key system warning light Indicates that the driver’s • Shift the shift door has been opened or lever to P. closed with the shift lever not •...
Page 463 5-2. Steps to take in an emergency ■ The tire pressure warning light may turn on due to natural causes The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temper- ature.
Page 464 If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
Page 465 Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer. ● Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes.
Page 466 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light).
Page 467: If A Warning Message Is Displayed (Vehicles With Multi-Information Display)
If any of the warning lights turns on again after performing the fol- lowing actions, contact your Toyota dealer. I n f o r ma t i o n P r o v i d e d b y :...
Page 468 Stop the vehicle immediately. ● The following warning indicates the possibility of damage to the vehicle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning message Details Indicates an abnormal engine oil pressure.
Page 469 Have the vehicle inspected immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning message Details Indicates a malfunction in the steering lock sys- tem.
Page 470 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light turns off. Warning message Details Correction procedure Indicates that one or more of the doors is not fully closed.
Page 471 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the trunk is not fully closed. A buzzer sounds to indicate that the trunk Close the trunk. is not fully closed (with the vehicle having reached a speed of 3 mph [5 km/h]).
Page 472 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the engine oil is sched- uled to be changed. A buzzer also sounds. Comes on approxi- Check the engine oil, mately 4500 miles and change if neces- (7200 km) after the sary.
Page 473 5-2. Steps to take in an emergency Follow the correction procedures (vehicles with smart key system). After taking the specified steps to correct the suspected problem, check that the warning light turns off. Interior Exterior Correction Warning message Details procedure buzzer buzzer Indicates that...
Page 474 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details procedure buzzer buzzer Indicates that the driver’s door has been opened and closed with the Turn the shift lever in P, “ENGINE the “ENGINE START STOP” 3 times START STOP”...
Page 475 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details procedure buzzer buzzer Indicates that a door has been opened or Press the closed and the “ENGINE “ENGINE START STOP” ⎯ Once START STOP” switch while switch has been depressing the turned twice to brake pedal.
Page 476 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details procedure buzzer buzzer Indicates that Press the the steering “ENGINE lock has not START STOP” released within switch again ⎯ 3 seconds of while turning Once pressing the the steering “ENGINE wheel with the...
Page 477: If You Have A Flat Tire
5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
Page 478 5-2. Steps to take in an emergency Vehicles with a full-size spare tire Transport eyelet (if equipped) Jack handle Wheel nut wrench Jack Spare tire Taking out the jack Remove the jack cover. STEP Remove the hook. STEP I n f o r ma t i o n P r o v i d e d b y :...
Page 479 5-2. Steps to take in an emergency Taking out the spare tire Remove the luggage floor cover. STEP Loosen the nut and remove it. STEP Remove the spare tire cover. Loosen the bolt and remove it. Remove the spacer (with alu- minum wheels).
Page 480 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. STEP Wheel Flat tire chock posi- tions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of...
Page 481 5-2. Steps to take in an emergency Slightly loosen the wheel nuts STEP (one turn). Turn the tire jack portion “A” by STEP hand until the notch of the jack is in contact with the jack point. Raise the vehicle until the tire is STEP slightly raised off the ground.
Page 482 5-2. Steps to take in an emergency Installing the tire Remove any dirt or foreign mat- STEP ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Page 483 5-2. Steps to take in an emergency Replacing an aluminum wheel with an aluminum wheel Turn the nuts until the washers Disc wheel come into contact with the disc wheel. Washer Lower the vehicle. STEP Firmly tighten each nut two or STEP three times in the order shown in the illustration.
Page 484 5-2. Steps to take in an emergency Stow the flat tire, tire jack and all tools. STEP ■ The compact spare tire ● The compact spare tire is identified by the label “TEMPORARY USE ONLY” on the tire sidewall. Use the compact spare tire temporarily only in an emergency. ●...
Page 485 5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
Page 486 5-2. Steps to take in an emergency CAUTION ■ Replacing a flat tire Observe the following precautions to reduce the risk of death or serious injury. ● Never use oil or grease on the wheel bolts or wheel nuts. Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage.
Page 487 ■ When replacing the tires When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. ■...
Page 488: If The Engine Will Not Start
5-2. Steps to take in an emergency If the engine will not start If the engine still does not start after following the correct starting procedure (→P. 131, 135) or releasing the steering lock (→P. 133, 136), confirm the following points. ■...
Page 489 ● There may be a malfunction in the steering lock system (vehi- cles with smart key system). Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function (vehicles with smart key system) When the engine does not start, the following steps can be used as an interim measure to start the engine if the “ENGINE START STOP”...
Page 490: If The Shift Lever Cannot Be Shifted From P (Automatic Transmission)
(a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted.
Page 491: If You Lose Your Keys
5-2. Steps to take in an emergency If you lose your keys New genuine keys can be made by your Toyota dealer. For vehicles with the smart key system, bring the other key and the key number stamped on the key number plate. For vehicles without the smart key system, bring a master key and the key number stamped on the key number plate.
Page 492: If The Electronic Key Does Not Operate Properly (Vehicles With Smart Key System)
5-2. Steps to take in an emergency If the electronic key does not operate properly (vehicles with smart key system) If communication between the electronic key and the vehicle is inter- rupted (→P. 30) or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote con- trol cannot be used.
Page 493 5-2. Steps to take in an emergency Changing “ENGINE START STOP” switch modes and starting the engine Shift the shift lever to P and apply the brakes. STEP Touch the Toyota emblem side of STEP electronic “ENGINE START STOP” switch.
Page 494: If The Battery Is Discharged
You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below. STEP...
Page 495 STEP cables in the exact reverse order in which they were con- nected. Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible. ■ Starting the engine when the battery is discharged (vehicles with auto- matic transmission) The engine cannot be started by push-starting.
Page 496 5-2. Steps to take in an emergency CAUTION ■ Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. ● Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.
Page 497 5-2. Steps to take in an emergency NOTICE ■ To prevent damage to the vehicle (vehicles with manual transmission) Do not pull- or push-start the vehicle, because the catalytic converter may overheat and become a fire hazard. ■ When handling jumper cables Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them.
Page 498: If Your Vehicle Overheats
Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine. If the fans are not operating: Stop the engine and call your Toyota dealer. After the engine has cooled STEP STEP...
Page 499 Water can be used in an emer- gency if engine coolant is (→ unavailable. P. 488 Have the vehicle checked at the nearest Toyota dealer as soon as possible. ■ Overheating If you observe the following, your vehicle may be overheating.
Page 500 5-2. Steps to take in an emergency NOTICE ■ When adding engine coolant Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine. I n f o r ma t i o n P r o v i d e d b y :...
Page 501: If The Vehicle Becomes Stuck
5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. Stop the engine. Set the parking brake and put the shift STEP lever in P (automatic transmission) or N (manual transmis- sion).
Page 502 5-2. Steps to take in an emergency CAUTION ■ When attempting to free a stuck vehicle If you choose to rock the vehicle back and forth to free it, make sure the sur- rounding area is clear, to avoid striking other vehicles, objects or persons. The vehicle may also lunge forward or lunge back suddenly as it becomes free.
Page 503 5-2. Steps to take in an emergency I n f o r ma t i o n P r o v i d e d b y :...
Page 504: Specifications Maintenance Data (Fuel, Oil Level, Etc.)
Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 505 6-1. Specifications This number is also on the certifi- cation label on the driver’s side center pillar. ■ Engine number The engine number is stamped on the engine block as shown. 2.5 L 4-cylinder (2AR-FE) engine 3.5 L V6 (2GR-FE) engine I n f o r ma t i o n P r o v i d e d b y :...
Page 506 Drive belt type (2.5 L 4-cylinder [2AR-FE] engine only) The high strength drive belt is used for the generator side drive belt. When replacing the drive belt, use Toyota genuine drive belt or equivalent high strength drive belt. If the high strength drive belt is not used, durability of the belt may become less than expected.
Page 507: Lubrication System
6.0 qt. (5.7 L, 5.0 Imp. qt.) ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toy- ota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity. Oil grade: ILSAC multigrade engine oil 2.5 L 4-cylinder (2AR-FE) engine...
Page 508 6-1. Specifications How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use. 3.5 L V6 (2GR-FE) engine Recommended viscosity: SAE 5W-30 SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather.
Page 509 6-1. Specifications How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use. I n f o r ma t i o n P r o v i d e d b y :...
Page 510: Cooling System
(Reference) 3.5 L V6 (2GR-FE) engine 9.5qt. (9.0 L, 7.9 Imp. qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, Coolant type non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 511: Electrical System
Toyota dealer. NOTICE ■ Automatic transmission fluid type Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.
Page 512 6-1. Specifications Clutch 0.2 ⎯ 0.6 in. (5 ⎯ 15 mm) Pedal free play Fluid type SAE J1703 or FMVSS No.116 DOT 3 Brakes Automatic transmission 2.4 in. (61 mm) Pedal clearance Manual transmission 2.5 in. (63 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in.
Page 513 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) ® Automatic transmission fluid DEXRON Power steering fluid type or III Tires and wheels 3.5 L V6 (2GR-FE) engine with 16-inch tires P215/60R16 94V, Tire size T155/70D17 110M Driving under normal conditions Front: 30 psi (210 kPa, 2.1 kgf/cm bar)* Rear: 30 psi (210 kPa, 2.1 kgf/cm...
Page 514 6-1. Specifications 2.5 L 4-cylinder (2AR-FE) engine with 16-inch tires P215/60R16 94V, Tire size T155/70D17 110M Driving under normal conditions Front: 34 psi (230 kPa, 2.3 kgf/cm bar)* Rear: 34 psi (230 kPa, 2.3 kgf/cm bar)* Spare: Full-size spare tire 34 psi (230 kPa, 2.3 kgf/cm or bar) Tire inflation pressure Compact spare tire...
Page 515 6-1. Specifications Others P215/60R16 94V, P215/55R17 93V, Tire size T155/70D17 110M Driving under normal conditions Front: 32 psi (220 kPa, 2.2 kgf/cm or bar)* Rear: 32 psi (220 kPa, 2.2 kgf/cm bar)* Spare: Full-size spare tire 32 psi (220 kPa, 2.2 kgf/cm or bar) Tire inflation pressure Compact spare tire (Recommended cold tire...
Page 516 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights ⎯ Low beam High beam 9005 Front side marker/ ⎯ parking lights ⎯ Front turn signal lights Exterior ⎯ Rear turn signal lights ⎯ License plate lights Back-up lights Front fog lights ⎯...
Page 517: Fuel Information
ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada. ■ Fuel tank opening for unleaded gasoline To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps. ■...
Page 518 Toyota allows the use of oxygenate blended gasoline where the oxygen- ate content is up to 10% ethanol or 15% MTBE. ● If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87. ●...
Page 519 6-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s catalytic converters causing the emission control system to malfunction.
Page 520: Tire Information
6-1. Specifications Tire information Typical tire symbols Standard tire Compact spare tire Tire size (→P. 501) DOT and Tire Identification Number (TIN) (→P. 500) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators (→P.
Page 521 6-1. Specifications Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL”...
Page 522 6-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal...
Page 523 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol...
Page 524 U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
Page 525 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100.
Page 526 6-1. Specifications Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
Page 527 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
Page 528 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
Page 529 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same Intended outboard molding on the other sidewall of the tire, or sidewall...
Page 530 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load...
Page 531 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indicators designed to give a visual indication of the...
Page 532: 6-2. Customization
Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toy- ota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer. Customized Item Function Default setting...
Page 533 6-2. Customization Customized Item Function Default setting setting Time elapsed before 30 seconds automatic door lock function is activated if 60 seconds door is not opened after 120 seconds being unlocked Operation signal (Emergency flashers) Operation signal (Buzzer) Door lock buzzer Panic function Wireless remote con-...
Page 534 6-2. Customization Customized Item Function Default setting setting Driver's door unlocked in one All doors Unlocking using a key step, all doors unlocked in one unlocked in two step. steps Speed-detecting auto- matic door lock function Door lock Opening driver's door →...
Page 535 6-2. Customization Customized Item Function Default setting setting 7.5 seconds Time elapsed before 15 seconds lights turn off 30 seconds Operation when the doors are unlocked Vehicles with smart key Illumination system: Operation after → P. 313) the “ENGINE START STOP”...
Page 536: Initialization Items To Initialize
6-3. Initialization Items to initialize The following items must be initialized for normal system operation in cases such as after the battery is reconnected, or maintenance is performed on the vehicle. Item When to initialize Reference Engine oil mainte- nance data After changing engine oil P.
Page 537: Reporting Safety Defects For U.s. Owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 538: Seat Belt Instructions For Canadian Owners (In French)
Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 539 Guide de confort de ceinture de sécurité (siège arrière extérieur) Si la sangle diagonale gêne la personne au niveau du cou, utilisez le guide confort de la ceinture de sécurité. Sortez le guide confort de sa ÉTAPE poche. Engagez la ceinture dans le ÉTAPE guide.
Page 540 ■ Ceinture de sécurité arrière Si la ceinture de sécurité est sortie de son guide, repassez-la dedans avant de l'utiliser. Entretien et soin ■ Ceintures de sécurité Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Profitez de l'occasion pour vérifier régulièrement que les ceintures ne sont pas effilochées, entaillées, ou ne paraissent pas exagérément usées.
Page 541 I n f o r ma t i o n P r o v i d e d b y :...
Page 542: Alphabetical Index
Alphabetical index Alphabetical index A/C ........196, 204 Alarm...........82 ABS........... 170 Antenna........220 Air conditioning filter....398 Anti-lock brake system....170 Air conditioning system Armrest ........332 Air conditioning filter ..... 398 Ashtray........327 Automatic air conditioning Audio input .......258 system........ 196 Audio system Manual air conditioning Antenna.........220 system........
Page 543 Alphabetical index Back-up lights Child safety Wattage.........494 Airbag precautions ....94 Battery Battery precautions ..380, 473 Checking .......378 Child restraint system ... 104 If the vehicle has discharged Child-protectors.......43 battery.........471 How your child should wear Preparing and checking before the seat belt ......61 winter ........179 Installing child restraints..
Page 544 Alphabetical index Daytime running light Electronic key system ........161 If the electronic key does Defogger not operate properly....469 Rear window......209 Emergency flashers Side mirror......209 Switch........424 Dimension........ 482 Emergency, in case of Dinghy towing ....191,192 If a warning light turns on ..432 Display If a warning message is Trip information ....
Page 545 Alphabetical index Engine Floor mat ........335 Compartment ......365 Fluid Engine switch ....131, 135 Brake........375 Hood........362 Power steering fluid ....376 How to start the Washer........381 engine ......131, 135 Fog lights Identification number.....482 Switch ........163 If the engine will not start ..465 Wattage.........
Page 546 Alphabetical index Garage door opener....338 I/M test........358 Gas station information..536 Identification number Gauges ........147 Engine ........482 Glove box......... 317 Vehicle ........482 Glove box light ......317 Ignition switch....131, 135 Grocery bag hooks ....336 Illuminated entry system..314 Indicator lights ......151 Initialization Hands-free phone system...
Page 547 Alphabetical index Keyless entry......38 Maintenance Keys Do-it-yourself Electronic key......24 maintenance ....... 359 Engine switch ....131, 135 General maintenance.... 355 If you lose your keys .....468 Maintenance data ....482 If the electronic key does Maintenance requirements ... 353 not operate properly....469 Manual air conditioning Ignition switch....131, 135 system ........
Page 548 Alphabetical index Noise from under vehicle ..18 Radiator ........374 Radio .........215 Rear side marker lights Odometer ......147, 155 Replacing light bulb....418 Switch........159 Engine oil......368 Rear seats Opener Adjustment ......53 Fuel filler door......76 Folding down......54 Hood........362 Rear sunshade ......333 Trunk ........
Page 549 Alphabetical index Seat belts Service reminder Adjusting the seat belt.....57 indicators ......151 Automatic Locking Shift lever Retractor .......60 Automatic transmission..138 Child restraint system If the shift lever cannot installation......108 be shifted from P ....467 Cleaning and maintaining Manual transmission .....
Page 550 Alphabetical index Stop/tail lights Tachometer.......147 Replacing light bulbs .... 418 Theft deterrent system Wattage ........ 494 Alarm........82 Storage box ......336 Engine immobilizer system ..80 Storage feature......316 Theft prevention labels....84 Storage precautions ....175 Tire inflation pressure .....392 Stuck Tire information If your vehicle becomes Glossary ........504...
Page 551 Alphabetical index Vanity lights Warning messages Vanity lights......325 Engine coolant Wattage.........494 temperature ......445 Vanity mirrors......325 Engine oil maintenance..447 Vehicle identification Engine oil pressure ....445 number ........482 Hood ........447 Vehicle stability control...170 Moon roof......447 VSC..........170 Open door ......447 Parking brake......
Page 552: What To Do If
What to do if... What to do if... If you have a flat tire A tire punctures P. 454 P. 465 If the engine will not start P. 80 Engine immobilizer system The engine does not start P. 471 If the battery is discharged If the electronic key does not oper- P.
Page 553 What to do if... If a warning light turns on or a The warning light or indicator P. 432 warning buzzer sounds... light comes on Vehicles with multi-information display Vehicles without multi-information display I n f o r ma t i o n P r o v i d e d b y :...
Page 554 What to do if... ■Warning lights Brake system warning Tire pressure warning light light P. 435 Low windshield washer fluid warning light P. 432 P. 435 Charging system warn- Open door warning light ing light P. 433 P. 435 Low engine oil pressure Low fuel level warning warning light light...
Page 555: Gas Station Information
GAS STATION INFORMATION Auxiliary catch lever Trunk opener Fuel filler door P. 362 P. 47 P. 76 Hood lock release lever Fuel filler door opener Tire inflation pressure P. 362 P. 76 P. 491 Fuel tank capacity 18.5 gal. (70 L, 15.4 Imp. gal.) Fuel type Unleaded gasoline only P.

Toyota 2010 Camry Quick Reference Manual

Quick Links

QUICK REFERENCE

Related Manuals for Toyota 2010 Camry

Summary of Contents for Toyota 2010 Camry