Advertisement
Quick Links
Advertisement
Related Manuals for impulce 2 IT8003
Summary of Contents for impulce 2 IT8003
- Page 1 T8003 Arm Curl Assembly Instructions...
-
Page 2: Table Of Contents
Table of contents Important Safety Instructions--------------------------------- 1 Exploded View Diagram------------------------------------------ 2 Hardware List-------------------------------------------------- ------ Parts List----------------------------------------------------- ---------- Assembly instructions------------------------------------------... -
Page 3: Important Safety Instructions
Important Safety Instructions Before beginning any fitness program, you should obtain a complete physical examination from your physician. When using exercise equip- ment, basic precautions should always be taken, including the following: * Read all instructions before using the Arm Curl These instructions are written to ensure your safety and to protect the unit. -
Page 4: Exploded View Diagram
T8003 Arm Curl Exploded View Diagram... -
Page 5: Hardware List
Hardware List 1 10 14 0 Millimeters Inches... -
Page 6: Parts List
Parts List Item No. Description QTY Item No. Description Main Upright Bronze Bushing ID 25.4 Low Cross Allen Bolt M12×40 Seat Support Allen Bolt M10×115 Upper Cross Allen Bolt M10×80 Adj. Shaft Allen Bolt M10×70 Allen Bolt M10×45 Allen Bolt M10×35 Flange Allen Bolt M10×30 Seat Pad Support... -
Page 7: Assembly Instructions
Assembly instructions Assembly of the Arm Curl takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recom men ded to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. -
Page 8: Main Upright 1
Step1 Install the Adj. Foot Plates Align the Adj. Foot Plates(#28) to the Main Upright(#1), and the Seat Support(#3) then secure them by hands. -
Page 9: Low Cros(
Step2 Assemble The Frame 1)Attach the Low Cross(#2) and the Upper Cross (#4) to the Main Upright(#1) using: two Allen Bolts(#48) M10×115 two Allen Bolts(#49) M10×80 four Nylon Locknuts(#62) M10 eight Washers(#60) 11× 20×1.5 Φ Φ 2)Attach the Seat Support(#3) to the Low Cross(#2) and the Upper Cross(#4) using: four Allen Bolts(#50) M10×70 four Nylon Locknuts(#62) M10... - Page 10 Step3 Assemble The Pillow Block Attach the Pillow Block(#20) to the Main Upright(#1) using: two Allen Bolts(#47) M12×40 four Washers(#59) 13× 24×1.5 Φ Φ two Nylon Locknuts(#61) M12 two Spacer(#86)
- Page 11 Step4 Assemble The Arm 1)Insert the Arm(#6) into the Main Upright(#1) and thro- ugh the Pillow Block(#20). 2)Attach the Counter Poise Block(#19) to the Arm(#6) using: Spring Washer(#64) Φ two Shoulder Bolt(#54) M8×25...
- Page 12 Step5 Assemble The Cam Insert the Arm(#6) through the Main Upright(#1), the Spacer(#18) and the Cam(#7),next secure the Cam(#7) to the Arm(#6) using the key (#37).
- Page 13 Step6 Assemble The Pillow Block 1)Insert the Spacer(#17) onto the Arm(#6) as shown below. 2)Attach the Pillow Block(#20) to the Main Upright(#1) using: two Allen Bolts(#47) M12×40 two Nylon Locknuts(#61) M12 four Washers(#59) Φ 13× 24×1.5 Φ two Spacer (#86) 3)Secure the Arm(#6) to the Pillow Block(#20) using: one Allen Bolt(#58) M10×25 one Spring Washer(#63)
- Page 14 Step7 Assemble The Weight Plates 1)Insert both the Guide Rods(#15) into the Main Upright (#1). 2)Slide the Weight Rubber Bumper(#31)down onto each Guide Rod(#15). as shown below. 3)Carefully begin sliding the Weight Plate one by one in sequence:#39,#38,#41. 4)Align both top ends of the Guide Rods(#15) to the Main Upright(#1) and secure them using: two Allen Bolts(#50) M10×70 two Washers(#60)
- Page 15 Step8 Route The Cable 1)Put the clip tied on the weight pin leash onto the Top Plate(#41) as shown, next connect the Cable(#44) to the Top Plate(#41). 2)Route the Cable(#44) up and over the two Pulleies A (#23).then secure them to the Main Upright(#1) using two Allen Bolts(#51) M10×45 four Washers(#60) Φ...
- Page 16 Step9 Assemble The Decal Plates 1)Attach the two Decal Plates(#14,70) to the Main Upr- ight(#1) using: fourteen Butttons(#34) 2)Attach the Weight Shroud (#10)to the Main Upright (#1) using: four Bolt Covers(#67) four Plastic Washers(#66) four Screws(#57) The Front Decal Plate(#14) with the exercise instru- ctions printed on it should be attached in the front Note of the Main Upright(#1).
-
Page 17: Seat Pad Support 1
Step10 Assemble the Pads 1)Attach the Seat Pad(#21) to the Seat Pad Support(#9) using: two Washers(#60) Φ 11× 20×1.5 Φ two Allen Bolts(#51) M10×50 2)Insert the Seat Pad Support(#9) into the Seat Support (#3) and secure it into place using the Pop Pin(#35) and the Screw(#56).