Test Mode - Sony HCD-FR10W Service Manual

QQ
3 7 63 1515 0
[Version Display Mode]
* The software version is displayed.
Procedure:
1. Press three buttons of [VOLUME -], [VOLUME +] and A si-
multaneously for two seconds.
2. The message "VERSION" is displayed. The version display
mode is activated.
3. Press the > button. "IF ***" is displayed.
4. Each time the > button is pressed, the display changes in
the order of DVD, AREA, VERSION and IF.
5. To exit from this mode, press the ?/1 button.
[Key Test Mode]
* Button check
Procedure:
1. Press three buttons of [VOLUME -], [VOLUME +] and [FUNC-
TION] simultaneously.
2. The message "KEY NUM 0" is displayed and "0" blinks.
3. Each time a button is pressed, "KEY NUM 0" value increases.
However, once a button is pressed, it is no longer taken into
account.
4. When all buttons are pressed, "KEY NUM 9" appears and the
number blinking is stopped.
5. To exit from this mode, disconnect the power cord.
[Display Test Mode]
Procedure:
1. Press three buttons of [VOLUME -], . and A simulta-
neously.
2. All segments are turned on.
TE
L 13942296513
ALL1DISC S PGM ALBM TITLE
ALBM SHUF REP 1
MP3 JPEG
SA - CD MULTIPBC
3. When the > button is pressed, the display will light up as
follows.
ALL1DISC S PGM ALBM TITLE
ALBM SHUF REP 1
MP3 JPEG
SA - CD MULTIPBC
4. Press the > button and confirm the display.
5. Press the > button, all segments are turned off.
6. Every pressing of the > button turns on each segments in
the same order.
7. To exit from this mode, press the ?/1 button.
www
.
http://www.xiaoyu163.com
TRK CHAP SLEEP NTSC TUNED ST MONO NIGHT
TRK CHAP SLEEP NTSC TUNED ST MONO NIGHT
x ao
y
i
http://www.xiaoyu163.com
SECTION 5

TEST MODE

8
[Cold Reset]
* The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode when
returning the set to the customers.
Procedure:
1. Press the ?/1 button to turn the power on.
2. Press three buttons of . , HX and A simultaneously.
3. When this button is operated, display as "COLD RESET" for
a while and all of the settings are reset.
[Disc Slot Lock]
The disc slot lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure:
1. Turn the set on.
2. Press two buttons of x and A simultaneously for five sec-
onds.
3. The message "LOCKED" is displayed and the slot is locked.
Releasing Procedure:
1. Press two buttons of x and A simultaneously for five sec-
onds again.
2. The message "UNLOCKED" is displayed and the slot is
unlocked.
Note: When "LOCKED" is displayed, the slot lock is not released by
turning power on/off with the ?/1 button.
[Repeat Limit Release Mode]
Procedure:
1. Press three buttons of A , > and [VOLUME+] simulta-
neously.
Q Q
3 6 7 1 3
2. Repeat limit is released.
DSGX SB DEC
kHz a D EX
[CDM Ship Mode]
MHz a PL II
DTS-ES NEO:6
* This mode moves the optical pick-up to the position durable
to vibration. Use this mode when returning the set to the
customer after repair.
Procedure:
1. Turn the set on.
2. Set the function to DVD.
DSGX SB DEC
kHz a D EX
3. Press three buttons of > , . and A simultaneously.
MHz a PL II
DTS-ES NEO:6
4. The message "MECHA LOCK" is displayed.
5. The CDM ship mode is set.
u163
.
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
HCD-FR10W
9 9
2 8 9 9
23