Barco projection systems owner's manual (82 pages)
Summary of Contents for Barco 2100LC
Page 1
BARCO PROJECTION SYSTEMS RETRO DATA 2100LC R9001309 INSTALLATION MANUAL Date : 130298 Art. No : R5975968A...
Page 2
Produced by BARCO NV, January 1998. All rights reserved. Trademarks are the rights of their respective owners. BARCO nv/Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco on the web : http://www.barco.com Printed in Belgium...
How to enable or disable the password ..........................3-5 How to change the password menu ........................... 3-6 Switching on ....................................3-7 Projector status LED ................................... 3-7 Switching to standby .................................. 3-7 Switching off ....................................3-7 Lamp life ...................................... 3-8 Fuses ......................................3-8 5975968A RETRO DATA 2100LC 130298...
¯ 1- Power cord with outlet plug type ANSI 73.11. ¯ 1- Remote Control Unit, plus one 9V battery. & ¯ 1- Owner's Manual & ¯ 1- Installation Manual & ¯ 1- Safety Manual 5975968A RETRO DATA 2100LC 130298...
Unpacking and Projector Dimensions Projector dimensions (mm/") All measurements shown are in millimeters and inches. 5975968A RETRO DATA 2100LC 130298...
(rear side,) and securing through the far underside of the projection CPG@T hole opening. This will require some care in manoeuvring as the fixing is recessed when the two cabinets are in place. Ensure each screw is tightened fully by hand. 5975968A RETRO DATA 2100LC 130298...
It is now necessary to focus the corners of the picture by adjusting the Front Rotary Lens Ring (a), moving the desired amount in the anti clockwise direction. (a) Front Rotary Lens Ring (b) Main Lens Barrel Tube (c) Locking Fastener Ring 5975968A RETRO DATA 2100LC 130298...
GÃÃÃÃÃ S GÃÃÃ Ã ÃS GÃÃÃ Ã ÃS hard wire remote ÃSTÃ!"!ÃPVUÃ Ã8PH H ÃQPSUÃ ÃSTÃ!"!ÃDI Ã8USGÃ Internal mains connection permanently connected Internal power switch always to be positioned in the ’1’ (ON) state 5975968A RETRO DATA 2100LC 130298...
'Removing the Projector' next. Removing the Projector Attention Follow the procedure as described below, it is recommended that a qualified Barco technician performs the alteration of the password function. 9DT8PII@8UÃ6GGÃDIQVUPVUQVUÃ WARNING : Power down all devices and switch off, discon- 8PII@8UPSTÃPIÃUCDTÃÃQ6I@G...
Page 10
,a. The leftside panel is removed by removing all its fixing screws both on the front and back. Once the screws are removed gently lever evenly out of its position. LEFTSIDE PANEL FRONT FIXING SCREWS î LEFTSIDE PANEL BACK FIXING SCREWS 5975968A RETRO DATA 2100LC 130298...
Page 11
Ü Note: Extra care must be observed not to damage or scratch the projector lens during the rotating process. 23(5$7,21$/ 326,7,21 5(029$/ 326,7,21 Û 23(5$7,21$/ 326,7,21 5(029$/ 326,7,21 UPÃS@HPW@ÃASPHÃS@6S 5975968A RETRO DATA 2100LC 130298...
Remove the top cover by loosening or undoing its fixing screws as indicated above. Then slide the cover backwards slightly and lift off, PROJECTOR the internal structure will be now visible. COVER PROJECTOR FIXING PROJECTOR BRACKET FIXING BRACKET SCREWS 5975968A RETRO DATA 2100LC 130298...
IDENTIFICATION CHANGE PASSWORD CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUN TIME LAMP RUN TIME HISTORY PRESET INPUT BALANCE MORE ... Select with then <ENTER> <EXIT> to return. 5975968A RETRO DATA 2100LC 130298...
- press firstly the STAND-BY key and allow projector to cool down until the fans stop blowing (or at least 15 min). - then switch off the projector with the power switch on the front local control panel. 5975968A RETRO DATA 2100LC 130298...
Operating the lamp longer than the lamps corresponding hours may Ghà ÃvrÃvà Ãu damage the projector. Replace always with a same type of lamp. Call Pr hvtÃurÃyhÃytr a BARCO authorized service technician for lamp replacement. uhà Ãu ÃhÃqhhtr urà wrp WARNING : Using a lamp for longer than its Qyrhrà ryhprÃurÃyh...
Need help?
Do you have a question about the 2100LC and is the answer not in the manual?
Questions and answers