Advertisement
dusting brush – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool.
Crevice Tool – For corners and hard to reach areas.
Furniture Nozzle – For soft furniture and fabrics [13]
Parquet Caresse Nozzle* – For parquet floors and other delicate floors. [1U]
Pet Hair Remover mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for
deepcleaning on textile surfaces and other hard to clean areas. Particularly suitable for
pet hairs removal. [1V]
Allergen Remover mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for
deepcleaning on textile surfaces and other hard to clean areas. Particularly suitable for
allergen removal. [1w]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]
ImPORTANT: Do not use the grand turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
the brush is rotating.
ClEANER mAINTENANCE
Emptying the dust Container
When the dust reaches the max level indicator in the container empty the dust bin.
ImPORTANT:To maintain optimum performance do not allow the dust to sit higher than
the max level.
1.
Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2.
Hold the dust container over a bin with one hand and use the other hand press the
Dust Container Door Release Button. [15]
3.
Close the Dust Container door and refit to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a blue filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust. The filters
should be washed after 5 container empties or when the filter has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
IMPORTANT: Regularly check and maintain the filters by following the filter
maintenance instructions , it is also recommended that you purchase new filters
after every 3rd filter wash. This will maintain your cleaners performance.
ImPORTANT: Always ensure the filters are fully dry before use.
*Certain models Only ** Certain models only, nozzles may vary according to model
To access the pre-motor filter:
1.
Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2.
Hold the dust container with one hand and with the other hand rotate the bin handle
anti clockwise to release it from the dust container. [16]
Remove the blue filter pack located in the dust container handle. [17]
3.
4.
Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [18]
5.
Reassemble to filter pack once fully dry and refit to the cleaner.
ImPORTANT: Do not use the product without the filter pack fitted.
To access the exhaust filter:
1.
Release the container by sliding the dust container release button towards the rear
of the cleaner. Lift the dust container from the cleaner main body. [14]
2.
Unclip the exhaust filter cover from the dust container cradle on the cleaner main
body. [19]
Using the tab remove the exhaust filter from the cleaner main body. [20]
3.
4.
Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [21]
Cleaning the dust container / multi-cyclonic separation unit
This cleaner uses a multicyclonic separation system, unique to Hoover. If necessary the
separation unit can be disassembled from the dust container and cleaned.
1.
Release the dust container by sliding the dust container release button towards the
rear of the cleaner. Lift the dust container from the cleaner main body. [14]
2.
Hold the dust container with one hand and with the other hand rotate the dust
container handle anti clockwise to release it from the dust container. [16]
3.
Remove the multicyclonic separation unit from the dust container by pulling the
handle provided.[22]
4.
If necessary, use a cloth to remove excessive dust from the multi-cyclonic unit
surface. [23]
5.
Reassemble the multicyclonic separation unit to the dust container and refit the filter
pack in position.
6.
Reassemble the dust container handle to the bin container. Refit the dust container
to the cleaner.
NOTE: For stubborn dirt the multi-cyclonic separation unit, or the dust container can be
washed, but care must be taken to ensure that both are completely dry before use.
ImPORTANT: For optimum performance, we recommend that the multi-cyclonic
separation system is inspected after each empty.
Removing a blockage from the cleaner
1.
Check if the dust container is full. If so refer to 'Emptying the dust container'.
3
Advertisement
