1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. HDTV
  5. WD-57733
  6. Owner's manual

Mitsubishi Electric WD-57733 Owner's Manual

Dlp high-definition television
Hide thumbs Also See for WD-57733:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
DLP
HIGH-DEFINITION TELEVISION
®
MODELS
C Series
WD-C657
Y Series
WD-Y577, WD-Y657
733 Series
WD-57733, WD-65733, WD-73733
734 Series
WD-57734, WD-65734, WD-73734
OWNER'S GUIDE
• For questions:
-
Visit our website at www.mitsubishi-tv.com.
-
E-mail us at MDEAservice@mdea.com.
-
Call Consumer Relations at 800-332-2119.
• For information on System Reset, please see the back cover.
• To order replacement or additional remote controls, lamp cartridges, or Owner's Guides,
visit our website at www.mitsuparts.com or call 800-553-7278.
• Guidelines for setting up and using your new widescreen TV start on page 11.
x.v.Color

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi Electric WD-57733

Summary of Contents for Mitsubishi Electric WD-57733

  • Page 1 HIGH-DEFINITION TELEVISION ® MODELS C Series WD-C657 Y Series WD-Y577, WD-Y657 733 Series WD-57733, WD-65733, WD-73733 734 Series WD-57734, WD-65734, WD-73734 OWNER’S GUIDE • For questions: Visit our website at www.mitsubishi-tv.com. E-mail us at MDEAservice@mdea.com. Call Consumer Relations at 800-332-2119. • For information on System Reset, please see the back cover. • To order replacement or additional remote controls, lamp cartridges, or Owner’s Guides, visit our website at www.mitsuparts.com or call 800-553-7278. • Guidelines for setting up and using your new widescreen TV start on page 11. x.v.Color...

  • Page 2: Fcc Declaration Of Conformity

    TV WEIGHT: This TV is heavy! Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and discon- nect all cables before moving it. WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm. FCC Declaration of Conformity Product: Projection Television Receiver Models: WD-C657 WD-57733, WD-65733, WD-73733 WD-Y577, WD-Y657 WD-57734, WD-65734, WD-73734 Responsible Mitsubishi Digital Electronics America, Party: Inc. 9351 Jeronimo Road Irvine, CA 92618-1904 Telephone: (800) 332-2119 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 3: Table Of Contents

    Contents Important Information About Your TV General Warnings and Cautions, Notes on Installation and Operation ....Important Safeguards ..... 1 Television Overview Package Contents .

  • Page 4: Important Information About Your Tv

    Installation Notes Stand Requirement CAUTION: Use these Mitsubishi TV models only with the Mitsubishi stand models shown here. Other stands can result in instability and possibly cause injury. TV Model WD-57733 WD-Y577 WD-57734 WD-65733 WD-Y657 WD-65734 WD-C657 WD-73733 WD-73734 Custom cabinet installation must allow for proper air circulation around the television. NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT...

  • Page 5: Important Safeguards

    Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. Read, Retain and Follow All Instructions. Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. Heed Warnings. Adhere to all warnings on the appliance and in the operating instructions. Cleaning. Unplug the TV from the wall outlet before cleaning. Do not use liquid, abrasive or aerosol cleaners. Cleaners can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning. Attachments and Equipment. Never add any attachments and/or equipment without approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. Water and Moisture. Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash bowls, kitchen sinks, laundry tubs, in a wet basement, swimming pools, etc. Accessories. Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing serious injury to a child, adult or pet and serious damage to the TV. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the TV. Any mounting of the TV should follow the manufacturer’s instructions, and should use mounting accessories recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Ventilation. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer’s instructions have been adhered to. Power Source. This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company.

  • Page 6: Television Overview

    Television Overview Package Contents Please take a moment to review the following list of items to ensure that you have received everything. 1. Remote Control 2. Two AA Batteries 3. Owner’s Guide 4. Quick Reference Guide 5. Quick Connect Guide 6. Product Registration Card 7. Two-Ended IR Emitter (included with Y series and 734 models only) Special Features of Your TV Your new high-definition widescreen television has many special features that make it the perfect center of...

  • Page 7: Tv Front Panel

    TV Front Panel Control Panel Buttons on the front control panel duplicate Flip down cover to commonly used keys on use buttons and the remote control. The inputs on the front upper labels show control panel. functions when no TV menus are displayed; the lower labels indicate func- tions when TV menus are displayed or when a special function has been activated. See chapter 4, “TV Opera- tion and Features,” for the functions of these buttons. FORMAT MENU GUIDE INPUT FORMAT MENU GUIDE INPUT ENTER ENTER MENU MENU Front Control Panel.
  • Page 8 Front-Panel Indicators Off Steady On Slow Blinking LAMP Indicator LED Color TV Condition Normal TV on or standby condition. None TV just powered off and lamp is Green cooling. 1. Lamp access door is open or Yellow not secure. 2. No lamp installed. Lamp no longer illuminates and has reached the end of the lamp life. STATUS Indicator LED Color TV Condition Normal TV on or standby condition. None TV is too hot. Yellow TV may require service. TIMER Indicator LED Color TV Condition TV is powered off.

  • Page 9: Tv Back Panel

    TV Back Panel IR Emitter Jack included on Y series and 734 series ANT 2/ AUX models only. ANT 2 / AUX ANT 2 / AUX ANT 2 / AUX ANT 1 / MAIN ANT 1 / MAIN ANT 1 / MAIN DIGITAL AUDIO ANT 1 / MAIN 1. ANT 1/MAIN, ANT 2/AUX (Antenna) If you are connecting an antenna or direct cable without a cable box, connect the main antenna or cable source to ANT 1/MAIN.
  • Page 10 TV Back Panel, continued 5. INPUT 1, 2 (Audio and Video) INPUT 1 and 2 can be used to connect a VCR, Super VHS (S-VHS) VCR, DVD player, standard satellite receiver, or other A/V device to the TV. Each TV INPUT group consists of jacks for composite video, S-Video, and analog stereo audio. Note that when you connect to the S-video jack, the composite video jack is auto- matically disabled. INPUT 3 is a third set of composite video and stereo audio jacks located on the front of the TV for convenience. 6. HDMI™ Inputs The HDMI 1.3 (High Definition Multimedia Interface) sup- ports uncompressed standard and high-definition digital video formats and PCM digital stereo audio format. Use the HDMI inputs to connect to EIA/CEA-861 HDMI compliant devices such as a high-definition receiver or DVD player. These inputs support 480i, 480p, 720p, 1080i, and 1080p video formats. Mitsubishi recommends you use category 2 HDMI cables to connect HDMI 1.3 source devices. High-speed cat- egory 2 cables bring you the full benefits of Deep Color and x.v.Color. These inputs can also accept digital DVI video inputs. To connect a DVI input, use an HDMI-to-DVI adapter or cable plus analog audio cables. Connect the analog audio cables to the PC/DVI AUDIO INPUT on the TV to receive left and right stereo audio from your DVI device.

  • Page 11: Tv Setup

    TV Set-Up Guidelines for Setting Up and Using Your New Widescreen TV Getting Started 1. Review the important safety, installation, and oper- ating information at the beginning of this book. 2. Choose a location for your TV. • Allow at least four inches of space on all sides of the TV to help prevent overheating. Over- heating may cause premature failure of the TV as well as shortened lamp life. • Avoid locations where light may reflect off the screen. • See the stand requirements under “Important Information About Your TV.” 3. Install the batteries in the remote control. See the following page. See chapter 4, “TV Operation and Features” for more on use of the remote control. 4. Plug your TV into a power outlet. The TIMER indica- tor on the front of the TV will start blinking rapidly. After the TIMER indicator stops blinking, press the POWER key to power on the TV.

  • Page 12: Installing The Remote Control Batteries

    Parent menu, the Lock > Front Panel menu, and Setup > Edit > Lock. • Video Settings. Change video adjustments to get the best picture for your viewing conditions. See “AV Menu.” Note: You may wish to change the Picture Mode from the default Brilliant to either Bright or Natural, which are suitable for most home viewing envi- ronments. 2. To program the remote control to operate A/V devices not under NetCommand control, see Appendix D, “Programming the Remote Control.” TV Care • Lamp Cartridge. When the lamp cartridge needs replacement, replace the lamp yourself and save the cost of a service call. See Appendix C for instructions.

  • Page 13: Setting Up Tv Inputs

    Initial TV Setup, continued Change the Menu Language Choose to display on-screen menus in either English or Spanish (Español). Select a menu language in the Setup menu. 1. With the Setup menu displayed, press to high- light the Language icon. 2. Press to highlight either English or Spanish. 3. Press MENU to return the highlight to the top row of icons. Memorize Channels For ANT 1/MAIN and ANT 2/AUX To start channel memorization 1. With the Setup menu displayed, press to high- light the Scan icon.

  • Page 14: Controlling A/V Receiver Sound Volume

    Setting Up TV Inputs, continued Note: For connection and setup of a personal com- puter, see the information later in this chapter. 1. See chapter 3, “TV Connections,” for recommen- dations on connecting your devices. 2. Connect your devices to the TV, making note of which TV input is used for each device. The TV and the devices can be either on or off when connecting. First select a device type. Auto Input Sensing screen for most device types. The Learn icon appears only on models with NetCommand. 3. Power on the TV if not already on. When the TV detects a connection, the Auto Input Sensing screen opens.

  • Page 15: Using The Tv With A Personal Computer

    Using the TV with a Personal Computer Connecting a Computer to the TV Use one of the connection methods listed below based on your computer’s video output. Computer Video Connection Video Output Digital DVI DVI-to-HDMI cable or an HDMI cable with an HDMI-to- DVI adapter Note: If the computer’s audio output is a single mini jack, a mini audio-to- RCA-male “Y” adapter cable is also required. HDMI HDMI-to-HDMI cable IMPORTANT This TV accepts digital computer signals only. 1. See the TV specifications in Appendix A to confirm that your computer signal is compatible with the TV.

  • Page 16: Image Resolution

    Using the TV with a Personal Computer Computer Video Adjustments 1. Power on the computer if it is not already on. 2. Select PC from the Input Selection menu. To do this, press INPUT to open the Input Selection menu, move the highlight to the PC icon, and press ENTER. 3. Working from the computer, change the resolution of the computer image. View the computer image on the TV and maximize the computer resolution while maintaining a suitable aspect ratio for the image. 4. Perform TV video adjustments. Press VIDEO repeatedly to access video- adjustment options. The following additional adjustments are available for computer video: Horiz Position (Horizontal Position). Manually adjust the horizontal position. Vert Position (Vertical Position). Manually adjust the vertical position. 5. Press FORMAT repeatedly to find the picture format best suited to the image. See the chart on this page showing how different computer reso- lutions are displayed on the TV.

  • Page 17: Tv Connections

    TV Connections Before you Begin Auto Input Sensing The TV’s Auto Input Sensing feature automatically rec- ognizes most connections and prompts you to identify the type of device connected. See chapter 2, “TV Setup,” for more on Auto Input Sensing. Connection Types Review the connection types available on your input devices and use inputs that will give the best video quality. For example, choose HDMI over component video, and choose component video over S-video or composite video. Picture Quality For best picture quality, route signals directly from the input device to the TV; avoid routing video signals through an A/V receiver, for example. HDTV Cable Box or Satellite Receiver with Component Video If your cable box or satellite receiver has an HDMI output, use the connections for HDMI devices described later in this chapter. Required: RCA component video cables, left/right analog stereo audio cables. 1. Connect the cable from the outside cable or satel- lite service to CABLE IN or SATELLITE IN on the cable box or satellite receiver. See your device’s owner’s guide for instructions and cable compatibil-...

  • Page 18: Standard Cable Box, Satellite Receiver, Or Other Device With S-Video

    Standard Cable Box, Satellite Receiver, or Other Device with S-Video Required: S-Video cable and left/right analog stereo audio cables. 1. Connect the cable from the outside cable or satel- lite service to CABLE IN or SATELLITE IN on the cable box or satellite receiver. 2. Connect an S-Video cable from S-VIDEO OUT on the cable box or satellite receiver back panel to INPUT S-VIDEO on the TV back panel. 3. Connect left (white) and right (red) audio cables from AUDIO OUT on the cable box or satellite receiver to INPUT AUDIO L (MONO) and R on the TV back panel. Note: Refer to the cable box or satellite receiver Owner’s Guide for cable or dish antenna con- nections to the receiver. ANT 2 / AUX ANT 1 / MAIN DIGITAL AUDIO...

  • Page 19: Wall Outlet Cable (No Cable Box)

    Wall Outlet Cable (no cable box) It is very important to connect the incoming cable for your primary viewing source to ANT 1/MAIN. 1. Connect the primary incoming coaxial lead cable to ANT 1/MAIN on the TV back panel. 2. For an optional secondary antenna source, connect an antenna (or cable) to ANT 2/AUX. ANT 2 / AUX ANT 2 / AUX ANT 1 / MAIN ANT 1 / MAIN Figure 4. Wall Outlet Cable Mitsubishi strongly recommends you avoid using antennas with flat twin leads.

  • Page 20: Dvd Player With Component Video

    DVD Player with Component Video Component video cables and analog audio cables are required. 1. Connect the component video cables from Y Pb Pr VIDEO OUT on the back of the DVD player to the COMPONENT jacks on the TV back panel, match- ing the green, blue, and red colored connections. 2. Connect left (white) and right (red) stereo audio cables from AUDIO OUT on the back of the DVD player to COMPONENT AUDIO L (MONO) and AUDIO R on the TV back panel. ANT 2 / AUX ANT 1 / MAIN DIGITAL Figure 7. Connecting a DVD player with component AUDIO HDMI IR EMITTER...

  • Page 21: Vcr To An Antenna Or Wall Outlet Cable

    VCR to an Antenna or Wall Outlet Cable Required: Two-way RF splitter, 3 coaxial cables, right and left analog audio cables, either S-video or video cable. 1. Connect the incoming cable or antenna to IN on the RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel. 3. Connect one coaxial cable from OUT on the RF splitter to ANT 1/MAIN on the TV back panel. Figure 9. Connecting a VCR to an Antenna or Wall Outlet Cable 4. To use the TV speakers with the VCR, connect left (white) and right (red) audio cables from AUDIO OUT on the VCR to INPUT AUDIO L (MONO) and AUDIO R on the TV back panel. If your VCR is mono (non-stereo), connect only the white (left) cable.

  • Page 22: Vcr To A Cable Box (Audio & Video)

    VCR to a Cable Box (Audio & Video) Required: Two coaxial cables, right and left audio cables, S-Video or composite video cable, plus cables required to connect the TV to the cable box. 1. Connect the incoming coaxial cable to IN on the cable box. 2. Connect one coaxial cable from OUT on the cable box to ANTENNA IN on the VCR back panel. 3. Connect the cable box outputs to the TV as shown in one of the options listed below. This connection allows the TV to receive the best available signal directly from the cable box. See the referenced figures in this chapter, “TV Connections.” Figure 1: Component video output to the TV’s COMPONENT Y Pb Pr jacks; analog stereo audio to the associated AUDIO jacks. Figure 2: S-Video output to the TV’s INPUT S-VIDEO jack; analog stereo audio to the associated AUDIO jacks. Figure 3: HDMI output to the TV’s HDMI jack. Figure 10. Connecting a VCR to a cable box 4. To use the TV speakers with the VCR, connect left (white) and right (red) audio cables from AUDIO OUT on the VCR to INPUT AUDIO L (MONO) and...

  • Page 23: A/V Receiver (Sound System)

    A/V Receiver (Sound System) Most setups require either a digital audio cable or analog stereo audio cables. The TV makes all audio available in digital and analog formats: Analog audio coming into the TV is available as output in digital format on the DIGITAL AUDIO OUT jack. Digital incoming audio is available as analog output on the AVR AUDIO OUTPUT/AUDIO L (MONO) and AUDIO R jacks. Usually, only one of the following connections is required: • To connect an analog A/V receiver Connect left (white) and right (red) audio cables from AVR AUDIO OUTPUT/AUDIO L (MONO) and AUDIO R on the TV back panel to the TV AUDIO INPUT on the A/V receiver. • To connect a digital A/V receiver with Dolby Digital surround sound and PCM audio support: Connect one end of the digital audio cable to DIGITAL AUDIO OUT on the back of the TV.

  • Page 24: Camcorder

    Camcorder Inputs on the front of the TV offer the most conve- nient way to connect a camcorder. If your TV model does not have a front input matching the camcorder’s output, use one of the matching jacks on the back of the TV. Jacks on the TV front panel offer the most convenient way to connect a camcorder Composite Video Connection Required: Analog stereo audio and composite video cables supplied with the camcorder. 1. Connect a composite video cable from VIDEO OUT on the camcorder to INPUT 3/VIDEO or VIDEO/Y on the TV. 2. Connect left (white) and right (red) audio cables from AUDIO OUT on the camcorder to INPUT 3/ AUDIO L and AUDIO R on the TV. L-AUDIO-R L-AUDIO-R VIDEO...

  • Page 25: Tv Operation And Features

    TV Operation and Features Choosing a Viewing Source Input Selection menu Choose a viewing source from the Input Selection menu. The current TV input appears as a full-color icon in this menu. 1. Press INPUT to display the Input Selection menu. If there are only two inputs to the TV, INPUT switches between them without displaying the menu. 2. Highlight an input icon using 3. Press ENTER to switch to the input and close the menu. More About the Input Selection Menu • To assign meaningful names to the icons, see the Inputs > Name menu in chapter 5, “TV Menu Set- tings.” • To rearrange the icons, see the Inputs > Order menu in chapter 5, “TV Menu Settings.”...

  • Page 26: Remote Control

    Remote Control 1. POWER: Turns TV power on and off. 2. Slide Switch: Selects the A/V device to be con- trolled by the remote control. Set the slide switch to TV for operation of the TV and NetCommand- controlled devices. Control of additional devices requires programing (see Appendix D, “Program- ming the Remote Control.” 3. SLEEP: Sets the TV to turn off within 2 hours. 4. Digits/Letters: Press digits for channel numbers, then press ENTER for faster tuning. Use numbers — and the CANCEL key to enter digital sub-channel numbers. Use also for entering letters or names into menus. To select letters when naming channels, repeatedly press the associated number key. Press ENTER to set the letter. Special characters are available with the 1 and 0 keys: ! & blank space 5. —/CANCEL (SUB-CHANNEL/CANCEL): When entering digital channel numbers, adds a separator between main and sub-channel numbers. Clears FAV and some menu entries. 6. QV (QuickView™): Switches between the current channel and the last channel viewed. 7. MUTE: Turns TV sound on and off. 8.

  • Page 27: Channelview™ Channel Listings

    Remote Control, continued Record/Playback Keys Use any of these methods to enable the recording and playback commands: • Program the remote control for your DVR, VCR, or DVD player/recorder and set the slide switch to VCR, DVD, CABLE, or SAT. • Y and 734 series TVs: Perform NetCommand IR “learning” for the device. • Check HDMI devices for compatibility with the TV’s NetCommand for HDMI feature (see below). (PAUSE): Pauses a VCR, DVR, or DVD. See above for use during TV viewing. (PLAY): Plays a VCR, DVR, or DVD. (RECORD): Records with a VCR or DVR. (STOP): Stops play of a VCR, DVR, or DVD. (REVERSE): Rewinds a VCR. Reverse scans a DVR or DVD. (FORWARD): Fast forwards a VCR. Forward scans a DVR or DVD. Note: To operate other audio/video devices: • See Appendix D, “Programming the Remote Control.” • See chapter 6, “NetCommand,” for NetCommand IR “Learning” of device keys.

  • Page 28: Status Display

    Status Display Press the INFO key to see the on-screen status display. The most common displays are shown here. Seldom or never do all the status indi- cators appear at the same time. On-screen status display. Sample information shown for a digital program source. Analog Sources Source antenna or input Analog channel being received (antenna sources only) Analog channel name (if named in the Setup > Edit menu); antenna sources only. (Does not apply) Signal Type Being Received. Possible: On antenna sources or INPUT 1/2: 480i On component jacks: 480i, 480p, 720p, 1080i Screen Format in use. Possible: Analog 480i /480p signals: Standard, Expand, Zoom, Stretch, Stretch Plus, Narrow 720p/1080i signals: Standard, Wide Expand Current FAV bank number of channel (antenna sources only) (Does not apply) V-Chip rating (antenna sources or INPUT 1/2 only) 10.

  • Page 29: Fav (Favorite Channels)

    FAV (Favorite Channels) Use the six Fav channel banks to store groups of your favorite channels from ANT 1 and ANT 2. You can set up a Fav channel bank for each of your favorite program types or set up a bank for each TV user. You may prefer to perform FAV channel setup from a menu. See chapter 5, “TV Menu Settings,” and the Setup > Edit options. Using FAV Channels See the current FAV bank number View FAV banks Change FAV banks If no FAV banks are set up FAV Setup Using Only the Remote Control Add FAV channels Remove FAV channels This procedure removes the channel...

  • Page 30: Tv Signals And Display Formats

    TV Signals and Display Formats This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter. While there is no perfect solution for displaying a squarish, narrower image on a wide screen, Mitsubishi offers several display formats from which you can choose. Press FORMAT on the TV remote control to cycle through the available display formats. The last-used format for each device is used when you return to that device. DVD Definitions Anamorphic (or Enhanced for WideScreen TV) These DVDs are recorded in a special way to prop- erly show widescreen images on 16:9 TV sets using the Standard format mode. This is the recommended viewing choice. Non-Anamorphic (or 4:3, 1:33:1, Letter Box, or Full Screen) These DVDs are recorded for use with traditionally shaped, squarish TVs. They may be full screen (4:3 or 1:33:1) which crops movies to fit the narrow TV, or letter box, which adds black top and bottom bars.
  • Page 31 4. TV Operation and Features TV Display Formats See descriptions on the preceding page.

  • Page 32: Viewing Camera Files

    Viewing JPEG Picture Files JPEG Photos and the USB Photo Port 1. Connect your USB card reader or USB drive to the USB Photo port on the front of the TV. The USB Photo menu displays while files are being read. Wait until you see the completion message on screen before L-AUDIO-R VIDEO/Y continuing. Note: Some manufacturers’ devices may be incompat- ible with the TV. If the TV is unable to display your photos, you can: • Transfer files to a different USB device. • Use the camera’s composite video output as described later in this chapter. 2. Refer to the table below for use of the USB Photo menu after files have been read. USB Photo Menu Options Start slide show.

  • Page 33: Photos And Moving Video As Composite Video

    Slide Show Use these keys during the slide show: Keys for JPEG Picture Slide Show Begin or resume slide show playback Pause or resume playback while in auto- matic advance mode. Advance to the next slide. ENTER Go to the previous slide. FORMAT Rotate the slide clockwise in 90˚ incre- ments. Stop slide show and display the USB Photo menu. INFO Display status for the viewing device and current image. INPUT Display the Input Selection menu. MENU Display or remove the TV Main menu. Note: Always press (STOP) to stop slide show play- back before disconnecting from the USB Photo port. Media Setup Menu In the Media Setup menu you can adjust the slide show display, number of repetitions, or display interval. • Select either Auto or Manual advance. During manual operation, press or ENTER to advance to...

  • Page 34: Tv Menu Settings

    TV Menu Settings Remote Control Keys for the TV Menu System The following keys help you use the menu system. Some keys are duplicated on the TV’s front panel. MENU EXIT (Adjust Left/Right Keys) • Move through screens to select menu options. (Adjust Up/Down Keys) ENTER Numbers Letters CANCEL INFO Main Menu Press MENU on the remote control to open the Main menu. Icon Menu Name and Description AV Menu Captions Menu Setup Menu Inputs Menu Lock Menu Function Display or close the Main menu or move back one menu level.

  • Page 35: Av Menu

    AV Menu An on-screen slider displays when making some audio and video adjustments. Numeric values represented on the slider range from 0 (minimum) to 63 (maximum), with 31 as the mid-point. Note: The PerfecTint, SharpEdge, and Deep Field Im- ager video adjustments (marked §) are offered on 734 series models only. AV Menu Options Video See the description of video adjustments later in this section. Audio See the description of audio adjustments later in this section. • To reset audio and video adjustments for the current input, highlight the Reset icon and press ENTER. Reset • Reset has no effect on settings for Balance, Listen To, Language, and Film Mode. PerfectColor Sliders PerfectColor PerfectTint Sliders § Highlight the PerfectColor icon and press ENTER to display the PerfectColor menu. Settings are retained in memory independently for each TV input. • To switch between PerfectColor and PerfecTint adjustments, highlight Adjust Mode and press • Press • Press • Press CANCEL to restore default settings.

  • Page 36: Video Menu

    Video Menu To make video adjustments: • From the Video menu: 1. Press to highlight an option. 2. Press to make an adjustment 3. Press MENU to return to the AV menu. • While watching TV: Press the VIDEO key repeatedly to display the video option you want to change. Press to change settings. Note: See chapter 2, “TV Setup,” for additional adjust- ments available for images from a computer. Video Menu Options Picture Mode Brilliant Game Bright Natural Contrast • Adjust the white-to-black level • Low contrast shows a variety of shades in darker images • In most home lighting situations, medium contrast looks best.

  • Page 37: Audio Menu

    Audio Menu To make audio adjustments: • From the Audio menu: 1. Press to highlight an option 2. Press to make an adjustment 3. Press MENU to return to the AV menu. • While watching TV: Press the AUDIO key repeatedly to display the audio option you want to change. Press to change settings. Audio Menu Options Speakers The Speakers option displays if an A/V receiver connection has been detected. AV Receiver Bass Control volume level of low-pitched sound from the TV speakers. Treble Control volume level of high-pitched sound from the TV speakers. Balance Control audio balance between the right and left TV speakers Surround Simulated Stereo Surround Sound Listen To Stereo...

  • Page 38: Captions Menu

    Captions Menu Captions on Analog Channels The TV can decode captions from ANT 1/ANT 2 and INPUT 1/INPUT 2. Broadcasters can send either stan- dard closed captions or text service. Standard closed captions follow the dialogue of the program and display in a small section of the screen. Text-service closed captions often contain information such as weather or news and cover a large portion of the screen. IMPORTANT • Analog text-service options display a large black or gray box on the screen when no signal is being broadcast. • The content of captions is determined by the broadcaster.

  • Page 39: Setup Menu

    Setup Menu Use the Setup menu to: • Select English or Spanish for menus and on-screen text. • Scan the channels available for the antenna or cable service connected to the ANT 1 or ANT 2 jacks. • Edit channel options, including channel locking. • Set the TV’s internal clock. • Set the TV Timer to turn on the TV automatically at a designated time. • Set the energy mode for power consumption when the TV is powered off. Setup Menu Options English Spanish Language Ant-1 Air Ant-1 Cable Scan Ant-2 Air Ant-2 Cable Notes on Scan and channel memorization: • Channel memorization may take up to 15 minutes to complete.
  • Page 40 Setup Menu, continued Setup Menu Options Use the Edit menu to edit channel options when ANT 1 or ANT 2 is the current source, To highlight a channel number to edit: • Press CH / to jump to the next page of channel numbers. Press and hold CH Edit through pages. • Press to move through all channel numbers, one at a time. Press and hold through channel numbers. The TV tunes to the highlighted channel on release of CH Channel Channels marked with a check are in memory. To add or delete a channel from memory, highlight the channel number and press ENTER. To add a single digital channel not in the list, see the notes under Scan. Digital channels are listed by virtual channel number with the physical channel number shown in parentheses. Name Lets you assign a custom name up to six characters long to memorized channels. You can name analog channels and also name digital channels if broadcast without pre-assigned names. 1. With the cursor in the Name field, press a number key repeatedly to cycle through the characters associated with the key. 2. Press ENTER to set the letter and move to the next letter position. To delete the current character and move back one position, press CANCEL. Fav1–Fav6 Use the six Fav channel banks to store groups of your favorite channels. For example, you can set up a Fav channel bank for each of your favorite program types (e.g., sports, news, children’s programs) or set up a bank for each TV user.
  • Page 41 Setup Menu, continued Use either the manual or auto method to set the clock. Set the clock if you wish to: • Use the TV’s Timer function. • Maintain accurate ChannelView listings. Setup Menu Options Settings Clock Time (Manual option only) Date (Manual option only) Time Zone Daylight Savings Time Setup menu, Clock options Manual. To set the clock manually: 1. Select Manual. 2 Set the time of day. 3. Set the date. 4. Select your time zone. 5. Select either Applies or Ignore for Daylight Savings Time. Note: If using Manual, each time the time change occurs, you must open this menu and set the TV’s clock ahead or back.
  • Page 42 Setup Menu, continued Use the Timer to set a time for the TV to turn on auto- matically. Use this menu to set a day, time, input, and channel for the Timer. If the TV is already on at the requested time, the TV will automatically tune to the designated channel. • The TV clock must be set before you can use the Timer feature. • When the Timer turns on the TV, press any key on the remote control to keep it on. Otherwise, the TV will turn off after five minutes. • The POWER/TIMER indicator flashes green when the TV is off to indicate the TV Timer has been set. Setup Menu Options Timer On, Off Daily, Mon-Fri, (every) Sunday, (every) Monday, (every) Tuesday, etc. Timer Select the day or days of the week for the Timer to turn on the TV. Time To set the time for the TV to come on: 1. With the hour highlighted, press PM indicator. Press and hold to change the hour display quickly. 2. Press ENTER to highlight the minutes.

  • Page 43: Inputs Menu

    Inputs Menu Note: • NetCommand IR control of home-theater devices is available on Y series and 734 series models only. • When you change an input name in the Name menu and then exit the Name menu: The name is changed The icon in the Input Selection menu is changed Settings are changed to the defaults for the new device type. On models offering NetCommand control, all “learning” for the input is also erased. Inputs Menu Options Cable Box, Camcorder, Name DVD, DVD2, DVR, Game, HD Disc, Satellite, VCR, On/Off (ANT 1 and ANT 2 only) Off (HDMI only) Put frequently used icons at the start of the Input Selection menu. 1. Press Order 2. Press ENTER to confirm the selection.

  • Page 44: Lock Menu

    Lock Menu TV locks available from the Lock menu are: Lock by Ratings Parent Restrict access to programming based on V-Chip rating signals sent by the broadcaster. Other Lock by Time Time Restrict TV use by time of day. Lock Front Panel Front Disable the controls on the front Panel of the TV. Use this option if small children in the home try to press front-panel buttons. Note: Channel Lock is an additional lock that blocks access to specific channels. Channel Lock is available under the Setup menu (Setup > Edit > Lock). Setting or Resetting a Pass Code Setting a Pass Code You are prompted to enter a pass code whenever you select Lock on the Main menu. To set a pass code for...
  • Page 45 Lock Menu, continued Parent Menu Options (U.S.-based rating system) Option Name and Description Lock Off, On Disables or enables program blocking based on V-Chip signals and the U.S. rating system. TV-Y Youth. For children under 7. Rating TV-Y7 Youth 7 and older. TV-G General Audience. For the entire family. TV-PG Parental Guidance. Parental Guidance recommended; may not be suitable for some children. TV-14 Adolescent 14 and older. Not recommended for children under 14. TV-MA Mature Audience. For adults only. Fantasy Violence. Applies to TV-Y7 only. Sexual Dialog. Applies in differing degrees to TV-PG and TV-14.

  • Page 46: Front Panel

    Lock Menu, continued Other Menu Options (alternate rating system) This TV can recognize new rating systems that may come into effect in the future. The Other option remains grayed out until the TV receives a signal using an alternate rating system. Such alternate rating systems will apply to digital programming only. Option Name and Description Lock On, Off Enable or disable program blocking. System Name The rating system available for the channel Group Rating groups available in the rating system shown on the screen. Rating groups are defined by the rating system in effect. Rating Rating restrictions available in the selected rating system and group. Highlight the rating and press ENTER to check (block) or uncheck (allow) rated content. Time Block all use of the TV during the time period you specify. You must enter a pass code to use the TV when the time lock is in effect. Lock by Time On, Off Lock Time, To set the lock and unlock times: Unlock Time 1. Highlight the hour digits for the Lock Time.

  • Page 47: Netcommand

    NetCommand About NetCommand • NetCommand home-theater control is available on the following models: Y series WD-Y577, WD-Y657 734 series WD-57734, WD-65734, WD-73734. This chapter applies only to these models. • NetCommand setup is optional. • You can perform NetCommand setup when the TV first recognizes a device during Auto Input Sensing or at any convenient time afterward. • NetCommand operates by sending remote control signals from the TV to your other devices via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions. All this is accomplished with the TV’s remote control and the slide switch left in the TV position. • The IR “Learning” feature of NetCommand allows the TV to learn the remote control signals for your A/V devices. • You can choose the level of NetCommand control for your home theater. Standard Setup. Perform a standard setup if you want NetCommand to control only a few devices, such as the TV, a playback device (like a DVD player), and a cable box. With this setup, you can use the TV’s remote control to operate these devices. A/V Receiver Setup. Perform A/V receiver setup if you want NetCommand to: Control a surround sound A/V receiver.

  • Page 48: Ir Emitter Placement (Netcommand®)

    IR Emitter Placement (NetCommand®) An IR emitter cable is included with the TV. The NetCommand system uses emitters connected to the IR EMITTER jack to control other devices such as DVD players, cable boxes, satellite receivers, and VCRs. 1. Connect the plug end of the supplied IR emitter cable to the IR EMITTER NetCommand® jack on the TV back panel. 2. Run the cable for each of the emitter ends under, alongside, or over each device to be controlled so that the emitter end is in front of the area where the remote control sensor is located. 3. Position the emitter end with the emitter bulb facing the remote control sensor. The bulb emits infrared light in a cone-shaped pattern. Place the bulb far enough from the sensor to allow the cone pattern to reach the sensor. The IR sensor is usually behind the plastic window of the front display panel. It is sometimes visible with the aid of a flashlight and is normally a round or square cutout behind the plastic. If you cannot see the sensor and the device’s Owner’s Guide does not specify the location, you can find it by following these steps using the device’s remote control: a. Hold the device’s remote about one-half inch...

  • Page 49: Initial Netcommand Setup For Most Devices

    Initial NetCommand Setup for Most Devices To perform this procedure, you need: • The remote controls for both the TV and the device you want to control. • The IR emitter cable supplied with the TV. Note: To set up an A/V receiver, see “Set Up NetCommand Control of an A/V Receiver” later in this chapter. 1. Connect and position the IR emitters for the devices you wish to control. See “IR Emitter Place- ment” in this chapter. 2. Set the TV’s remote control slide switch to the TV position. 3. Open the NetCommand Learn screen in one of two ways: • If working from the Auto Input Sensing screen for the device, highlight the Learn icon and press ENTER to open the Learn screen for the device. • If performing NetCommand setup at any time after the device has been recognized through Auto Input Sensing: a. Press INPUT to open the Input Selection menu.

  • Page 50: Netcommand Specialized Device Keys

    NetCommand Specialized Device Keys Refer to this chart when “learning” device keys. “Learn” some, all, or none of the keys used for each device type. The chart has space for you to write in functions you assign to the F1–F4 keys. Key Name in Function Learning Screen Power On Power On or Power ON/OFF (toggle) Guide On Screen Program Guide or Disc Menus Channel Up Next Channel Higher Channel Dn Next Channel Lower Page Up Page Up in Guides Page Dn Page Down in Guides Menu Setup menu for device Adjust Up Adjust or arrow up Adjust Dn Adjust or arrow down Adjust Lt Adjust or arrow left Adjust Rt Adjust or arrow right...

  • Page 51: Operating Netcommand-Controlled Devices

    Operating NetCommand-Controlled Devices To Control Most Device Types As an example of NetCommand control, if you are watching your cable box and you wish to tune to the next channel higher, press CH/PAGE then sends the “learned” channel-up control signal to the cable box. 1. With an IR emitter properly positioned in front of the device, use the Inputs > Learn screen to perform NetCommand setup for the device. 2. When you wish to use the device, press INPUT to display the Input Selection menu. 3. Press to highlight the icon for the device. 4. Press ENTER to switch the TV to the device. Note: if you have set up automatic input switching for the A/V receiver, the A/V receiver will automatically switch to the correct input for the device. 5. To operate the device using the TV’s remote control, set the slide switch to the TV position. 6. Point the remote control at the TV (not the device) and press the key for the desired function. Special Operation Methods Key Name in Special Operation Description and Setup Learning Screen...
  • Page 52 Operating NetCommand-Controlled Devices, continued Key Name in Special Operation Description and Setup Learning Screen Guide Displaying the Disc Menu (DVD or high-defini- tion disc format) “Learn” the DISC MENU, TOP MENU, or other key as named on the original remote in the Guide learning position. Displaying the On-Screen Program Guide (cable box or satellite receiver) 1. “Learn” the GUIDE key on the original remote in the Guide learning position.

  • Page 53: Set Up Netcommand Control Of An A/V Receiver

    Set Up NetCommand Control of an A/V Receiver Perform this setup to: • Operate the A/V receiver’s power and volume functions with the TV’s remote control. • Enable the A/V receiver to switch automatically to the correct audio input when you select a device in the TV’s Input Selection menu. To set up control of an A/V receiver you need: • The remote controls for both the TV and the A/V receiver. • The IR emitter cable supplied with the TV. Note: To set up control of other device types, see “Initial NetCommand Setup for Most Devices” earlier in this chapter. Perform this setup using the Inputs > AVR screen, shown below. AVR screen overview 1. Power and volume commands the TV can send to the A/V receiver when “learned”...
  • Page 54 Set Up NetCommand Control of an A/V Receiver, continued Setup to Control Automatic Switching of A/V Receiver Audio Inputs Two different setups are described here: Setup 1: Automatic A/V Receiver Switching to TV Audio Input Setup 2: Automatic A/V Receiver Switching for a device sending audio directly to the A/V receiver • Audio Available from TV only: Use Setup 1. Audio from ANT 1 and ANT 2 must be sent to the A/V receiver from the TV’s DIGITAL AUDIO OUT or analog AVR AUDIO OUTPUT. Use Setup 1 to make the A/V receiver switch to its designated TV audio input when viewing these sources. • HDMI Digital Stereo Audio: Use Setup 1 Digital stereo audio from an HDMI connection is available both in digital format (from the TV’s...
  • Page 55 Set Up NetCommand Control of an A/V Receiver, continued • If the text stops flashing before the check mark appears, repeat this step. • To erase the IR code just “learned,” press CANCEL while the name is highlighted. 5. Press to highlight the name Input1. You can enter a custom name using the letters/numbers on the remote control. It is best to assign names to “learned” inputs that match the input names dis- played on the A/V receiver. For this example, enter the custom name TV using these guidelines: • To select a character, repeatedly press a number key on the remote control to cycle through the characters associated with the key. The following special characters are available by using the 1 and 0 keys: 1: ! & blank space / * - • Press ENTER to set the character and move the highlight to the next character. • To delete a character, highlight the character and press CANCEL. • To highlight the first character, repeatedly press CANCEL.
  • Page 56 Set Up NetCommand Control of an A/V Receiver, continued 5. Press to highlight the name Input2. Assign a custom name that matches the input name dis- played on the A/V receiver. For this example, enter the custom name DVD using the guidelines given earlier. 6. Press to move the highlight to the second Assign column. 7. Use to highlight DVD in the list of devices recognized by the TV. The triangular marker always shows the assigned sound source. 8. Press EXIT if finished or continue for additional TV sources.

  • Page 57: Appendices

    Appendices Appendix A: Specifications ..... . . Appendix B: Bypassing the Parental Lock ....Appendix C: Lamp Cartridge Replacement and Cleaning .

  • Page 58: Appendix A: Specifications

    Appendix A: Specifications Size, Weight, and Power Consumption Dimensions (inches) Model Height Width Depth WD-C657 39.5 58.2 15.3 WD-57733 51.2 13.9 WD-65733 39.5 58.2 15.3 WD-73733 43.6 65.2 17.5 WD-Y577 51.2 13.9 WD-Y657 39.5 58.2 15.3 WD-57734 51.2 13.9 WD-65734 39.5...

  • Page 59: Appendix B: Bypassing The Parental Lock

    Appendix B: Bypassing the Parental Lock IMPORTANT Cut along the dotted line and file bypass instructions in a safe place for future reference. Appendices Bypassing the Parental Lock After you set the lock, you must use your pass code to view a locked program, view the locked TV, view a locked channel, cancel the lock, or enter the Lock menus. If you forget your pass code, you can view the locked TV without entering your pass code. When you are prompted for your pass code, press the number 9 and QV keys on the TV remote control at the same time. This process temporarily unlocks the TV. When entering the Lock menu, this process deletes your old pass code and prompts you to enter a new pass code. • You can either enter a new pass code to open the Lock menu and make changes or press EXIT to close the menu.
  • Page 60 Appendices This page intentionally left blank...

  • Page 61: Appendix C: Lamp-Cartridge Replacement And Cleaning

    Appendix C: Lamp-Cartridge Replacement and Cleaning THE ACCESS PANEL IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING PANEL COMPLETELY. BURN DANGER! HOT SURFACES INSIDE! Touch lamp cartridge handle only. Do not touch lamp or lamp cartridge housing. Keep lamp cartridge horizontal during removal. Do not tilt as glass may come out and cause injury. Only replace lamp cartridge with CAUTION: If the television is on, press POWER to turn it off.
  • Page 62 Appendix C: Lamp-Cartridge Replacement and Cleaning, continued Lamp-Cartridge Replacement Removing the Old Lamp Cartridge 1. Turn off TV power and allow the lamp to cool for at least one hour before proceeding. 2. After the lamp has cooled, remove the cover of the lamp compartment, located on the back of the TV. Refer to figures 1 and 2. Use a #2 (large) Phillips screwdriver to loosen the screw securing the cover. Keep the screw and cover for re-installation 3. With a large Phillips or flat-blade screwdriver, loosen the two shiny screws securing the lamp cartridge until they disengage from the mating threads. These are captive screws and cannot be separated from the lamp cartridge. 4. Fully open the bag supplied with the replacement lamp and set the opened bag aside. 5. Gently grasp the handle of the lamp cartridge and pull the old cartridge straight out. See figure 3. CAUTION: Do not tilt or rotate the cartridge, as small glass fragments may fall out. 6. Without tilting or putting down the lamp cartridge, insert it into the opened bag. Close the bag while being careful not to let any glass particles fall out.

  • Page 63: Appendix D: Programming The Remote Control

    Appendix D: Programming the Remote Control This appendix explains programming the TV’s remote control to operate other A/V devices. This is distinct from NetCommand control. The TV’s remote control can operate other devices by three different methods: • Remote Control Programming: You must move the slide switch to the position specific to the type of device. • NetCommand® IR “learning” (Y and 734 series only): You can operate other devices with the slide switch in the TV position. • NetCommand for HDMI devices (all TV models): You may be able to operate compatible HDMI devices with the slide switch in the TV position. See the device’s Owner’s Guide and the description in chapter 4, “TV Operation and Features.” Functions Available for Other A/V Devices The TV’s remote control can be programmed to operate other types and brands of A/V products. To use the remote when programmed, set the slide switch to the position labelled for the product type. The functions performed in each switch position can vary depending on the product. Not all functions work for all models.

  • Page 64: Programming The Remote Control

    Appendix D: Programming the Remote Control, continued Programming the Remote Control 1. Move the slide switch at the top of the remote to the position for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each slide-switch position. Switch Position Affected Device CABLE/SAT Cable Box DTV Receiver Satellite Receiver Laser Disc Player DVD Player/Recorder DVD Player/Recorder Laser Disc Player AUDIO A/V Receiver Audio Amplifier CD Player 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Release the POWER button. 4. Enter the first five-digit code listed for your equip- ment.

  • Page 65: Programming Codes

    Appendix D: Programming the Remote Control, continued Programming Codes Audio Amplifiers Brand Code Acurus 30765 Adcom 31100, 30577 Altec Lansing 31742 Aragon 30765 Bel Canto 31583 Design Bose 30674 Carver 30892 Classe 31462, 31461 Curtis Mathes 30300 Durabrand 31561 Elan 30647 30078 Harman/Kardon 30892 30331 Klipsch...
  • Page 66 Appendix D: Programming the Remote Control, continued Programming Codes, continued CD Players Brand Code Aiwa 30157 Akai 30156 Arcam 30157 Audio-Technica 30170 Burmester 30420 California Audio 30303, 30029 Labs Carver 30437, 30299, 30179, 30157 Classic 31297 Denon 30873, 30034, 30003 30000 DMX Electronics 30157 Emerson...
  • Page 67 Appendix D: Programming the Remote Control, continued Programming Codes, continued Cable Boxes Brand Code Optimus 10021 Pace 11877, 10237, 10008 Panasonic 10107, 10021, 10000 Panther 10637 Paragon 10000 Philips 11305, 10317, 10153, 10031, 10027, 10025 Pioneer 11877, 10877, 10533, 10144, 10023 Popular 10400 Mechanics...
  • Page 68 Appendix D: Programming the Remote Control, continued Programming Codes, continued DVD Players/Recorders Brand Code 20785 Nesa 20717 Next Base 20826 NexxTech 21402 Norcent 21265, 21107, 21003, 20872 Onkyo 20792, 20627, 20503 OptoMedia Elec- 20896 tronics Oritron 20651 Panasonic 21762, 20703, 20632, 20503, 20490 Philips 21354, 21267,...
  • Page 69 Appendix D: Programming the Remote Control, continued Programming Codes, continued Satellite Receivers Brand Code Toshiba 11749, 11285, 10819, 10790, 10749 UltimateTV 11640, 11392 Uniden 10724, 10722 US Digital 11535 USDTV 11535 Voom 10869 Zenith 11856 VCRs and DVRs Brand Code 21972 Admiral 20479, 20209, 20048...
  • Page 70 Appendix D: Programming the Remote Control, continued Programming Codes, continued VCRs and DVRs Brand Code Polk Audio 20081 Portland 20020 Profitronic 20240 Proscan 20761, 20760, 20202, 20060 Protec 20072 Pulsar 20039 Quarter 20046 Quartz 20046 Quasar 21162, 20162, 20077, 20035 RadioShack 21037, 20000 Radix 20037...

  • Page 71: Appendix E: Troubleshooting

    Appendix E: Troubleshooting TV Reset Comparison Guide You can resolve many common TV problems using the reset functions described in the following table. See also the additional troubleshooting suggestions later in this appendix. IMPORTANT Before you change sound or picture settings: If picture or sound settings seem wrong for a broadcast Reset Name When to Use Format When the picture shape seems incorrect, use FORMAT to change the shape of the picture. PerfectColor™ When the color intensities and PerfecTint™ seem out of balance, Reset use the PerfectColor/ (for the single PerfecTint reset to reset input currently the color balances to the being watched)
  • Page 72 Appendix E: Troubleshooting, continued Reset Name When to Use Front-Panel Lock To re-enable the front- Release panel controls after activation of the Front- Panel Lock System Reset If the TV does not turn on or off, does not respond to the remote control or front panel buttons, or has audio but no video. TV Reset To reset all consumer- IMPORTANT: accessible settings Use this reset and all memories to the only if all other original factory defaults. resets have been CAUTION: All owner- unsuccessful. performed setups and adjustments will be erased. Service and Support Service If you are unable to correct a problem with your TV, consult your Mitsubishi dealer or Mitsubishi Con-...
  • Page 73 Appendix E: Troubleshooting, continued General TV Operation Symptom A fan is running even while the TV is powered off. The TV remote control does not work. When I try to use the remote control, the POWER key blinks five times. TV does not respond to the remote control or to front panel control and TV will not power on or off. When a device is selected from the Input Selection menu, the screen is blue (no signal source). You have forgotten your Lock menu pass code. Rating restrictions are not working. On-screen displays appear each time you change a function. A warning message appeared on screen stating, “TV will shut down in a few seconds. Please check if the air flow is blocked.” TV Channels Symptom The TV takes several seconds to respond to channel changes. You cannot access a channel. Remarks The room is too warm. When the TV is off, internal components continue to draw power and must be cooled by the fan. • Check that the batteries are fresh and installed correctly. • Check that the slide switch on the remote is set to TV. • Be no more than 20 feet from the TV when using the remote control.
  • Page 74 Appendix E: Troubleshooting, continued TV Channels Symptom Name options are not available for some channels. When ChannelView™ list is displayed, infor- mation appears incomplete TV Power On/Off Symptom TV takes an excessively long time to power You cannot program the TV to turn on auto- matically (Timer function) The TV will not turn on after being plugged in. If light on front panel is blinking, wait for at least one minute for TV turned itself off and the light on the front panel started to blink. TV turned itself off and the STATUS is a steady yellow. TV will not power off. Picture Symptom Picture does not look like a high-definition picture. Picture has become dimmer. There is a large black or gray rectangle on the screen. You cannot view a picture when playing a VHS tape. Remarks You can name only memorized analog channels and memorized digital channels not named by the broadcaster. • Available information is sent from the broadcaster or cable provider. No other data is available. • Make sure the TV clock is set correctly.
  • Page 75 Appendix E: Troubleshooting, continued Picture Symptom VCR or DVD player’s on-screen menus jitter up and down. When viewing a stopped VCR, white lines are rolling on the screen. Screen is black. Picture from an HDMI input is noisy (poor quality). The image from a computer appears dis- torted when viewed on the TV. Sound (see also NetCommand troubleshooting for A/V receiver setup) Symptom There is no sound even when the volume is turned up. The sound does not match the screen picture. Indicators Symptom LAMP indicator light is a constant red. LAMP indicator light is a flashing yellow. Lamp cover door is open or lamp cartridge is not secure. See STATUS indicator light is a steady yellow. Remarks Possible cause: Many VCRs and DVD players provide on- screen menus at only half-resolution. These lower-resolution graphics may appear to jitter up and down when the TV con- verts them to high-definition graphics.
  • Page 76 Appendix E: Troubleshooting, continued Indicators Symptom STATUS indicator light is a steady/flash- ing red. NetCommand (Y and 734 series only) Symptom Cannot see the menu from the A/V Receiver. NetCommand unable to learn specific device keys. The A/V Receiver is the selected audio source but there is no sound. There is no sound when I switch to the A/V receiver using the Speaker setting in the AV menu, even though I have physically connected the TV to the A/V receiver and learned IR codes for the receiver inputs. There is no sound from the A/V receiver for my DVD player or other surround sound device even though I learned the IR code for the A/V receiver’s DVD input or other input. I’ve selected my DVD player or other sur- round sound device in combination with the TV speakers but hear no sound from the TV speakers. I “learned” the RECORD key for my VCR/DVR but when I pressed the RECORD key, the VCR/DVR did not record anything. Remarks • Unplug set from AC power. Plug back in an wait one minute for blinking to stop. • Press SYSTEM RESET button and wait for blinking to stop.

  • Page 77: Trademark And License Information

    Trademark and License Information LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABIL- ITY OR FITNESS FOR A PARTICULAR PURPOSE. Digital Light Processing™ and DLP™ are registered trademarks of Texas Instruments. Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories. HDMI™ the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited pay-per-view uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly prohibited. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc. The logo and the words “Simplay™” and “Simplay HD™” are the trademarks of Silicon Image, Inc. ChannelView™, ClearThought®, NetCommand®, PerfectColor™, PerfecTint™, QuickView™ are trademarks of Mitsubishi Digital Electronics America, Inc. x.v.Color and the x.v.Color logo are trademarks of Sony Corporation.

  • Page 78: Mitsubishi Tv Software

    Mitsubishi TV Software END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement. The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws and treaties. The Software is licensed, not sold. LICENSE GRANT. MDEA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the Software only with the Mitsubishi television model that included this owner’s guide and owned by you. RIGHTS AND LIMITATIONS. Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that Software has been pre installed. Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law. Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more than one TV. No Rental. You may not rent, lease, lend, or sublicense the Software. Trademarks. This License Agreement does not grant you any rights to any trademarks of MDEA. VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License, may subject you to serious criminal and civil penalties including damages and an award to MDEA of attorneys’ fees in connection with any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This license is effective until terminated, and will terminate immediately without notice from MDEA or judicial resolution if you fail to comply with any provision of this License. COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs, animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned by or licensed to MDEA. All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property...

  • Page 79: Mitsubishi Dlp™ Projection Television Limited Warranty

    Mitsubishi DLP™ Projection Television Limited Warranty MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper workmanship and/or material: a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any soft- ware incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at retail. We will repair or replace, at our option, any defective part without charge for the part. Parts used for replace- ment may be replaced with those of like kind and quality and may be new or remanufactured. Parts used for replace- ment are warranted for the remainder of the original warranty period. b. Embedded Software. MDEA warrants that all software incorporated into this television set (the “Embedded Soft- ware”) will perform in accordance with the functional description of Embedded Software in all material respects, but MDEA does not warrant that the Embedded Software is error-free. MDEA also does not warrant that the Embedded Software will be compatible under IEEE 1394 AV/C and HAVi software standards with products produced by any other manufacturer. The limited warranty contained in this section shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice within the warranty period, MDEA determines that the Embed- ded Software has failed to perform in accordance with such functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MDEA shall modify or replace the nonconforming Embedded Software at no charge to you, which at MDEA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card for Customer installation. The foregoing shall be MDEA’s sole obligation to you under this limited warranty. All rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by MDEA. c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticu- lar screen if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some Embedded Software, the consumer is solely responsible for any replacement labor. For all other parts, we will provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year from the original date of purchase at retail. d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period.
  • Page 80 c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner Registration Card so that we can contact you should a question of safety arise which could affect you. d. To obtain a replacement lamp, order the lamp directly from the MDEA Parts Department at (800) 553-7278. 2. THIS LIMITED WARRANTY DOES NOT COVER: a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated). b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MDEA, such as power surge damage caused by electrical system or lightning. This limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered under this limited warranty, all costs, expenses or any other damages arising from product installation, or set-ups, any adjustments of user controls (including con- trast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems, or service of products pur- chased or serviced outside the U.S.A. Please consult the operating instructions contained in the Owner’s Guide furnished with the product for information regarding user controls. 3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVI- SION, MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF ONE YEAR. 4. UNDER NO CIRCUMSTANCES SHALL MDEA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. 5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of inci- dental, special, or consequential damages, so the above limitations or exclusions may not apply to you. 6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state where the television was purchased and the laws of such state will govern. MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road Irvine, CA 92618-1904...

  • Page 81: Index

    Index A/V Memory Reset 71 A/V Receiver Adding NetCommand Control 53, 54, 55, 56 and the TV Speakers 37 and TV’s Remote Control 53, 63 Audio Lock 64 Codes 65 Connecting 9, 10, 23, 54 Controlling Sound Volume 14 A/V Reset 7, 71 Adjust Keys (Up/Down/Left/Right) 26, 34 Air Filter 62 Anamorphic Picture Format 30 Antenna Connecting 19 Antenna Inputs (ANT 1/MAIN, ANT 2/ AUX) 9 Audio Lock 64 Audio Menu 37 Auto-off. See Sleep Timer Auto-on. See Timer Auto Input Sensing Description 6 TV Setup 13 Back Panel (described) 9, 10 Batteries 12 Bright (Lamp Mode) 35 Cable Box and TV’s Remote Control 26, 63 Codes 66...
  • Page 82 Parent Menu 45 Pass Code Resetting 59 Setting 44 PAUSE Key 26 PerfectColor 35 PerfectTint 35 Photo Viewing 33 Picture AV Menu Controls 35 Format Displays 31 Picture Quality and Film Mode Troubleshooting 74 Picture Mode 36 Power Consumption Energy Mode 42 Specifications 58 Power On/Off 12, 25 Troubleshooting 74 QV Key (QuickView™) 26 and FAV Key 29 Remote Control Keys and Functions 26, 27 Programming Codes (reference chart) 65 Programming Instructions 64 Programming vs. NetCommand “Learning” 63 Reset 27 Reset A/V Reset (all settings) 7 AV Menu Reset (by input) 35 Color 71 Pass Code 59 Remote Control 27 Remote Control Audio Lock 64 System Reset 7 TV Reset Comparison Guide 71 S-Video 10 Connecting an S-Video Device Safeguards 5...
  • Page 84 For questions, call Consumer Relations at remote controls, lamp cartridges, or Owner’s Guides © 2007 Mitsubishi Digital Electronics America, Inc. 853B542D20 Website: www.mitsubishi-tv.com E-mail: MDEAservice@mdea.com 800-332-2119 To order replacement or additional Visit our website www.mitsuparts.com or call 800-553-7278 SYSTEM RESET If the TV does not respond to the remote control, front panel controls, or will not power on/off, press the SYSTEM RESET button on the front panel. The green LED will flash quickly for about one minute. When the green LED stops flashing, you may turn on the TV. Settings changes you made most recently, before using SYSTEM RESET, may be lost.

This manual is also suitable for:

Wd-73733Wd-73734Wd-c657Wd-y577Wd-y657Wd-65734 ... Show all

Table of Contents