Mitsubishi Electric XL5980LU User Manual page 5

WARNING:
Unplug immediately if there is something
wrong with your projector.
Do not operate if smoke, strange noise or odor comes out
of your projector. It might cause fire or electric shock. In
this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's Guide, do
not attempt to service this product yourself. Please contact
your dealer when you want to fix, adjust or inspect the
projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or drop it.
Unplug the projector and contact your dealer for
inspection. It may lead to fire if you keep using the
equipment.
Do not face the projector lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projection on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when it is operating.
It may hurt your eyes.Never let children look into the lens
when it is on.
Do not turn off the main power abruptly or
unplug the projector during operation.
It can lead to lamp breakage, fire, electric shock or other
trouble. It is best to wait for the fan to turn off before
turning main power off.
Do not touch Air outlet grille and Bottom plate
which becomes hot.
Do not touch them or put other equipment in front of Air
outlet grille. The heated Air outlet grille and Bottom plate
may cause injury or damage to other equipment. Also, do
not set the projector on the desk which is easily affected by
heat.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as
set out in the interference-causing equipment standard entitled "Digital Apparatus", ICES-003 of the Depart-
ment of Communications.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventilation slots
become clogged with dirt or dust, the temperature inside of
the projector may rise and cause some troubles, such as dam-
age of inside parts, and shortening the life of panel.
Do not look into the air outlet grille when
projector is operating.
Heat, dust etc. may blow out of it and hurt your eyes.
Do not insert your fingers in the space
between the lens and the cabinet.
The lens may shift causing injury or damage to the projector.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fire.
Place of installation
For safety's sake, refrain from setting the projector at any
place subjected to high temperature and high humidity.
Please maintain an operating temperature, humidity, and
altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+104°F (+40°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the projec-
tor so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or
subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from in-
stalling near the projector any cable carrying a large cur-
rent.
• Place the projector on a solid, vibration free surface: oth-
erwise it may fall, causing serious injury to a child or
adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious
injury and damage to the projector.
• Slanting the projector more than ±15˚(right and left or
front and rear) may cause trouble or explosion of the
lamp.
• Do not place the projector near air-conditioning unit or
heater to avoid hot air to the exhaust and ventilation
hole of the projector.
EN – 5