Download Print this page

Mitsubishi Electric WD510U-G Control Manual

Controlling the projector using a personal computer.
Hide thumbs
   

Advertisement

DLP Projector
WD510U/WD510U-G
WD500U-ST
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions :
Turning the power ON or OFF
Changing input signals
Inputting commands by pressing the buttons on the control panel and remote control
Menu setting
Connection
Important:
Make sure that your computer and projector are turned off before connection.
Boot up the computer first, and then plug the power cord of the projector.
(If you do not follow this instruction, the Comport may not function.)
Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1) Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
FLOW CONTROL
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the reverse type cable should be used.
2) Control command diagram
The command consists of the address code, function code, data code, and end code. The length of the command
varies among the functions.
Address code
HEX
30h 30h
ASCII
'0' '0'
[Address code] 30h 30h (In ASCII code, '0' '0') fixed.
[Function code] A code of each fixed control move.
[Data code]
[End code]
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bit]
NONE
Function code
Function
Function
A code of each fixed control data (number) and not always indicated.
0Dh (In ASCII code, '
Data code
Data
Data
') fixed.
1
End code
0Dh

Advertisement

   Also See for Mitsubishi Electric WD510U-G

   Related Manuals for Mitsubishi Electric WD510U-G

   Summary of Contents for Mitsubishi Electric WD510U-G

  • Page 1

    DLP Projector WD510U/WD510U-G WD500U-ST Controlling the projector using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : • Turning the power ON or OFF • Changing input signals • Inputting commands by pressing the buttons on the control panel and remote control •...

  • Page 2

    3) Control sequence (1) Send the command from the personal computer to the projector. (2) The projector will send a return command after it receives an end code. If the command is not received cor- rectly, the projector will not send the return command. (3) The personal computer checks the command and confirms if the sent command has been executed or not.

  • Page 3

    6) Keystone commands (Not executable in stand-by mode. Possible only to read during muting.) The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc.) ITEM ASCII KEYSTONE(vertical) How to set the value...

  • Page 4

    [Example] When enabling the password lock of DISPLAY INPUT (in the case that the password is 123412): Sending commands from the PC, etc. 30 30 50 53 4C 4F 43 4B 31 31 32 33 34 31 32 0D '0' '0' 'P' 'S' 'L' 'O' 'C' 'K' '1' '1' '2' '3' '4' '1' '2' ' 10) Reading command diagram The projectors operating status, such as POWER-ON/OFF and the currently selected input terminal, etc.

  • Page 5

    ITEM ASCII WALL SCREEN WALL SCREEN (BEIGE) WALL SCREEN (LIGHT BLUE) WALL SCREEN (LIGHT GREEN) WALL SCREEN (PINK) LAMP MODE AUTO POWERON APON AUTO POWER OFF APOF SPLASH SCREEN BACK COLOR AV MUTE MODE IMAGE REVERSE ASPECT PASSWORD FUNCTION PSLOCK 50h MENU POSITION CINEMA MODE CINE...

  • Page 6

    [Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D '0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' [Example 3]...

This manual also for:

Wd500u-st, Wd510u, Xl650u, Xl550u

Comments to this Manuals

Symbols: 0
Latest comments: