Mitsubishi Electric XD211U Information Sheet page 3

6) Keystone commands
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
KEYSTONE(vertical)
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII '+' '–'
HEX 2Bh 2Dh
7) Mute commands
screen is being displayed, the splash screen is not muted but only canceled.)
The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h).
ITEM
AV MUTE
8) Remote commands
screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
Button's name on remote
▲
▼
t
s
MENU
ENTER
AUTO POSITION
FREEZE
ASPECT
[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII
codes.):
Sending commands
from the PC, etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' ' '
9) Reading command diagram
The projectors operating status, such as POWER-ON, the currently selected input terminal and lamp operating
time, etc. can be monitored.
POWER ON
INPUT COMPUTER
INPUT VIDEO
INPUT S-VIDEO (only for XD211U)
LAMP OPERATING TIME
(on a LOW mode basis)
The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the
received command it's current operating status as the data code and send it back to the PC. (LAMP OPERATING
TIME: "h" and "m" represent hour and minute respectively. )
[Example ] When checking the currently selected input terminal (when the INPUT VIDEO is being selected) :
Sending commands
from the PC, etc.
30 30 76 49 0D
'0' '0' 'v' 'I' ' '
(Not executable in stand-by mode. Possible only to read during muting.)
ASCII HEX
KS 4Bh 53h
'0' '1' '2' '3'
30h 31h 32h 33h
(Not executable in stand-by mode. When the mute commands are sent while the splash
ASCII HEX
MUTE 4Dh 55h
(Not executable in stand-by mode. When the remote commands are sent while the splash
ASCII HEX
r53 72h
r2b 72h
r4f 72h
r59 72h
r54 72h
r10 72h
r09 72h
ra4 72h
re2 72h
Status code from
the projector
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
Function
vP
vI
vI
vI
vLE
Status code from
the projector
30 30 76 49 76 31 0D
'0' '0' 'v' 'I' 'v' '1' '
VALUE
±20
'4' '5' '6' '7'
34h 35h 36h 37h
VALUE
0 (OFF), 1 (ON)
54h 45h
35h 33h
32h 62h
34h 66h
35h 39h
35h 34h
31h 30h
30h 39h
61h 34h
65h 32h
'
ASCII
Data (Receive)
"1" when power-on mode
"0" when standby mode
r1
v1
v2
hhhhmm
'
3
'8' '9'
38h 39h
Description
Command operating the same
as the MENU button
Command receipt confirmation
(Command echo back)
HEX
Function
76h 50h
76h 49h
76h 49h
76h 49h
76h 4Ch 45h
Description
Command for checking the input terminal
Check result ( VIDEO)
Data (Receive)
31h
72h 31h
76h 31h
76h 32h
hhhhmm