Advertisement

Quick Links

QQ
3 7 63 1515 0

SERVICE MANUAL

Ver. 1.2 2006.02
HCD-SV2D is the Amplifier, DVD player, Tape
Deck and Tuner section in CMT-SV2D.
This system incorporates Dolby
Surround System.
1)
Manufactured under license from Dolby Laboratories.
"Dolby", "Pro Logic", and the double-D symbol are trademarks
of Dolby Laboratories.
2)
Manufactured under license from Digital Theater Systems,
Inc. "DTS" and "DTS 2.0 + Digital Out" are trademarks of
Digital Theater Systems, Inc.
TE
L 13942296513
Amplifier section
AUDIO POWER SPECIFICATIONS
(USA model only)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 6 ohm loads, both channels driven, from
120 – 10,000 Hz: rated 50 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
North American model:
Front speaker
Continuous RMS power output (reference):
Total harmonic distortion less than 0.07% (6 ohms at
Other models:
The following measured at AC 120 V, 240 V, 50/60 Hz
DIN power output (rated) 40 + 40 watts
Continuous RMS power output (reference)
www
.
Sony Corporation
9-879-645-03
Home Audio Division
2006B16-1
Published by Sony Techno Create Corporation
© 2006.02
http://www.xiaoyu163.com
1)
2)
Digital and DTS
Inputs
TV IN (phono jacks):
MIC (phone jack)(Asian models only):
Outputs
VIDEO OUT (phono jack):max. output level
DIGITAL OUT (OPTICAL) (Square optical connector
jack, rear panel)
Wavelength
PHONES (stereo mini jack):
50 + 50 watts (6 ohms at
SPEAKER:
1 kHz, 10% THD)
1 kHz, 25 W)
Disc player section
System
Laser
(6 ohms at 1 kHz, DIN)
50 + 50 watts
(6 ohms at 1 kHz, 10%
THD)
x
ao
y
i
http://www.xiaoyu163.com
HCD-SV2D
8
Digital
Model Name Using Similar Mechanism
DVD
DVD Mechanism Type
Section
Traverse Mechanism Name
TAPE
Model Name Using Similar Mechanism
Section
Tape Transport Mechanism Type
Q Q
3
6 7
1 3
SPECIFICATIONS
voltage 1 V,
impedance 47 kilohms
sensitivity 1 mV,
impedance 10 kilohms
1 Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
660 nm
accepts headphones of
8 ohms or more
accepts impedance of
6 ohms
Compact disc and digital
audio and video system
Semiconductor laser
(DVD: λ=650 nm,
CD: λ=780 nm)
Emission duration:
continuous
u163
.
2 9
9 4
2 8
1 5
0 5
8
2 9
9 4
Frequency response
Video color system format
Tape deck section
Recording system
Frequency response
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
— Continued on next page —
m
DVD DECK RECEIVER
co
9 9
US Model
E Model
HCD-DV2D
KDA898ST
1ADOMEZ0412
HCD-DV2D
CMAL5Z220C
2 8
9 9
DVD (PCM 48 kHz):
2 Hz – 22 kHz (±1 dB)
CD: 2 Hz – 20 kHz (±1 dB)
Pan-American models:
NTSC
Other models: NTSC, PAL
4-track 2-channel stereo
40 – 13,000 Hz,
using Sony TYPE I
cassette
87.5 – 108.0 MHz
(50 kHz step)
FM lead antenna
75 ohms unbalanced
10.7 MHz

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-SV2D

  • Page 1: Service Manual

    3 7 63 1515 0 SERVICE MANUAL US Model E Model Ver. 1.2 2006.02 HCD-SV2D is the Amplifier, DVD player, Tape Deck and Tuner section in CMT-SV2D. This system incorporates Dolby Digital and DTS Digital Model Name Using Similar Mechanism HCD-DV2D Surround System.
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Table Of Contents

    HCD-SV2D Ver. 1.1 3 7 63 1515 0 TABLE OF CONTENTS Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. SERVICING NOTES ..........4 GENERAL ..............5 This appliance is classified as a CLASS 1 LASER product.
  • Page 4: Servicing Notes

    HCD-SV2D Ver. 1.1 SECTION 1 3 7 63 1515 0 SERVICING NOTES MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP – Back Panel – BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc.
  • Page 5: General

    MIC/ECHO LEVEL +/– TV wa (29, 38) ql (28, 31) (30) VOLUME +/– 0 (13, 27, 28) m/M (rewind/fast forward) w; (13, 28) ./> (go back/forward) w; (12, 28) L 13942296513 HCD-SV2D Asian model only Except for HCD-SV2D Asian model u163 http://www.xiaoyu163.com...
  • Page 6 HCD-SV2D 3 7 63 1515 0 Remote control ALPHABETICAL ORDER BUTTON DESCRIPTIONS ?/1 (power) 1 (10, 32, 44) A – J K – Z O RETURN 3 (15) ANGLE qa (20) KARAOKE PON qg (30) M/m/</, 8 (11, 13, 20, 38,...
  • Page 7: Setting The Clock

    HCD-SV2D 3 7 63 1515 0 Setting the clock Use buttons on the remote for the operation. Press ?/1 to turn on the system. Press CLOCK/TIMER SET. Press . or > repeatedly to set the hour. Press ENTER. Press . or > repeatedly to set the minute.
  • Page 8: Disassembly

    HCD-SV2D Ver. 1.1 SECTION 3 3 7 63 1515 0 DISASSEMBLY 3-1. DISASSEMBLY FLOW • This set can be disassembled in the order shown below. 3-13. LID TC 3-2. COVER TOP, DC FAN (Page 14) (Page 9) 3-3. AMP BOARD, AV BOARD,...
  • Page 9: Cover Top, Dc Fan

    HCD-SV2D 3 7 63 1515 0 Note: Follow the disassembly procedure in the numerical order given. 3-2. COVER TOP, DC FAN 5 cover top 3 five s crews (+BTP 3 × 8) 9 four s crews (+BVTP 3 × 8) 7 s crew (+BVTP 3 ×...
  • Page 10: Mpeg Board

    HCD-SV2D 3 7 63 1515 0 3-4. MPEG BOARD 7 wire (flat type) (5core) (J703) 5 wire (flat type) 1 three s crews (9core) (J701) (+BTP 3 × 8) 6 connector 4 wire (flat type) (9P) (J702) (24core) (J705)
  • Page 11: Panel (Dvd)

    HCD-SV2D 3 7 63 1515 0 3-6. PANEL (DVD) 3 two claws 4 panel (DVD) screwdriver 3-7. DVD LOADER (KDA898ST) L 13942296513 1 two s crews 2 two s crews (+BVTP 3 × 10 ) (+BVTP 3 × 10 )
  • Page 12: Front Panel Section

    HCD-SV2D 3 7 63 1515 0 3-8. FRONT PANEL SECTION 6 two s crews (+BVTP 3 × 8 ) 9 connector (8P) (CN201) 7 earth wire 8 wire (flat type) (21core) (CN501) 3 screw (+KTP 3 × 8) qs claw 4 screw (+KTP 3 ×...
  • Page 13: Cassette Deck Mechanism (Cmal5Z220C)

    HCD-SV2D Ver. 1.1 3 7 63 1515 0 3-10. CASSETTE DECK MECHANISM (CMAL5Z220C) 1 wire (flat type) (7core) 3 shield cover 2 four screws (+BVTP 3 × 10) 4 cassette deck mechanism (CMAL5Z220C) L 13942296513 3-11. KEY BOARD 6 KEY board...
  • Page 14: Traverse Mech (1Adomez0412)

    HCD-SV2D 3 7 63 1515 0 3-12. TRAVERSE MECH (1ADOMEZ0412) 4 screw qg traverse mech 5 washer (1ADOMEZ0412) qd dumper (traverse mech) 7 screw 8 washer w ire (flat type) 24core 9 screw qs two dumpers q; washer (traverse mech)
  • Page 15: Test Mode

    HCD-SV2D SECTION 4 3 7 63 1515 0 TEST MODE PANEL TEST MODE Note 1: Regarding the notification symbol “R” • This mode is used to check the software version, LCD, LED Because the number of the operating buttons of this product are and keyboard.
  • Page 16 HCD-SV2D 3 7 63 1515 0 1. STARTING TEST MODE DVD SECTION 1. Press the ?/1 button to turn the power on, and set the function to DVD. [GENERAL DESCRIPTION] 2. While pressing the x and Z button at the same time, rotate The Test Mode allows you to make diagnosis and adjustment easily the [VOLUME+] knob clockwise to enter the test mode.
  • Page 17 HCD-SV2D 3 7 63 1515 0 2-1-1. Check DSP 2-2. SERVO Test MENU 1. Select the menu “Check DSP” and press the ENTER “R” 1. Select the menu “SERVO Test Menu” and press the button, then execute this mode.
  • Page 18 HCD-SV2D 3 7 63 1515 0 2-3-2. VFD Test MENU 1. Select the menu “VDF Test Menu” and press the ENTER “R” button, then execute this mode. 2. When the check is completed with success, “OK” appears. When the check finds any failure, “fail” appears..
  • Page 19: Mechanical Adjustments

    HCD-SV2D SECTION 5 SECTION 6 3 7 63 1515 0 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head record/playback heads pinch rollers demagnetizer.
  • Page 20 HCD-SV2D 3 7 63 1515 0 3. Mode: Playback DVD SECTION test tape MAIN board P-4-A100 [RF Level Check] (10kHz, –10dB) JK102 Check the RF level when optical pick-up block (TRAVERSE speaker terminal oscilloscope MECH) is replaced. Connection: oscilloscope...
  • Page 21: Diagrams

    HCD-SV2D Ver. 1.1 SECTION 7 3 7 6 3 1 5 1 5 0 DIAGRAMS • Circuit Boards Location THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Schematic Diagrams.
  • Page 22: Block Diagrams - Mpeg-1 Section

    HCD-SV2D 7-1. BLOCK DIAGRAMS — MPEG-1 SECTION — 3 7 6 3 1 5 1 5 0 OPTICAL PICK-UP RFOP 55 EFNINP XIN 134 Y701 55 RFN U708 RFON 54 EFNINN 16.9344MHz XOUT 135 S-RAM CAO 62 LDON2 22...
  • Page 23: Mpeg-2 Section

    HCD-SV2D — MPEG-2 SECTION — 3 7 6 3 1 5 1 5 0 MPEG1 DATA& ADDRESS BUS SECTION UD708 UD707 FLASH MEMORY EEPROM 11 28 3-1,48, 4-8, 30,32,34,36, 29,31,33,35, 38,40,42,44 17,16,9 39,41,43,45 18-25 MRST 115,118,120, 105,107,109, 147-150,152 131,133-138...
  • Page 24: Audio Section

    HCD-SV2D Ver. 1.1 — AUDIO SECTION — 3 7 6 3 1 5 1 5 0 E3,SP,TH JK202 IC402(2/2) IC401 MIC AMP IC402(1/2) ECHO DISK MIC AMP Q403-405 MIC IN BUFFER IC102 MIXER AMP Q401,402 IC101 IC103 MIC MUTE...
  • Page 25: Panel/Power Section

    HCD-SV2D Ver. 1.1 — PANEL/POWER SECTION — 3 7 6 3 1 5 1 5 0 PT901 POWER TRANSFORMER(MAIN) D306 Q315 -33V(VPP) -33V D309 D301 Q306 IC501 (2/2) SWITCH SYSTEM CONTROLLER Q305,Q320 D324 POWER AMP B+ POWER IC651 VFD651...
  • Page 26: Printed Wiring Board - Main Section-1

    HCD-SV2D Ver. 1.1 7-2. PRINTED WIRING BOARD — MAIN SECTION-1 — • See page 21 for Circuit Boards Location. :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MAIN BOARD TUNER KEY BOARD MPEG BOARD MPEG BOARD...
  • Page 27: Printed Wiring Board - Main Section-2

    HCD-SV2D Ver. 1.1 7-3. PRINTED WIRING BOARD — MAIN SECTION-2 — • See page 21 for Circuit Boards Location. :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MAIN BOARD • Semiconductor Location Ref. No. Location...
  • Page 28: Schematic Diagram - Main Section

    HCD-SV2D Ver. 1.2 • See page 41, 42 for IC Block Diagrams. • See page 39 for Waveforms. • See page 45 for IC Pin Function Description. 7-4. SCHEMATIC DIAGRAM — MAIN SECTION — 3 7 6 3 1 5 1 5 0...
  • Page 29: Printed Wiring Board - Mpeg Section-1

    HCD-SV2D • See page 21 for Circuit Boards Location. 7-5. PRINTED WIRING BOARD — MPEG SECTION-1 — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MPEG BOARD MONITOR DEBUGGER DEBUG TERMINAL • Semiconductor Location Ref. No.
  • Page 30: Printed Wiring Board - Mpeg Section-2

    HCD-SV2D • See page 21 for Circuit Boards Location. 7-6. PRINTED WIRING BOARD — MPEG SECTION-2 — :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 MPEG BOARD 1 3 9 4 2 2 9 6 5 1 3...
  • Page 31: Schematic Diagram - Mpeg Section

    HCD-SV2D Ver. 1.1 7-7. SCHEMATIC DIAGRAM — MPEG SECTION — • See page 42, 43 and 44 for IC Block Diagrams. • See page 39 for Waveforms. • See page 47, 51 for IC Pin Function Description. 3 7 6 3 1 5 1 5 0...
  • Page 32: Printed Wiring Board - Key Section

    HCD-SV2D Ver. 1.1 7-8. PRINTED WIRING BOARD — KEY SECTION — • See page 21 for Circuit Boards Location. :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 E3,SP,TH HP BOARD MIC BOARD MIC BOARD HP BOARD...
  • Page 33: Schematic Diagram - Key Section

    HCD-SV2D Ver. 1.1 7-9. SCHEMATIC DIAGRAM — KEY SECTION — • See page 40 for IC Block Diagram. 3 7 6 3 1 5 1 5 0 KEY BOARD (FLUORESCENT INDICATOR TUBE) IR651 REMOTE CONTROL RECEIVER Q651, Q652 SOL DRIVER -29.2...
  • Page 34: Printed Wiring Board - Av Section

    HCD-SV2D • See page 21 for Circuit Boards Location. 7-10. PRINTED WIRING BOARD — AV SECTION — 7-11. SCHEMATIC DIAGRAM — AV SECTION — 3 7 6 3 1 5 1 5 0 :Uses unleaded solder. AV BOARD AV BOARD...
  • Page 35: Printed Wiring Board - Amp/Power Section

    HCD-SV2D Ver. 1.1 7-12. PRINTED WIRING BOARD — AMP/POWER SECTION — • See page 21 for Circuit Boards Location. :Uses unleaded solder. 3 7 6 3 1 5 1 5 0 AMP BOARD AMP BOARD MAIN • Semiconductor BOARD...
  • Page 36: Schematic Diagram - Amp Section

    HCD-SV2D Ver. 1.1 7-13. SCHEMATIC DIAGRAM — AMP SECTION — • See page 44 for IC Block Diagram. 3 7 6 3 1 5 1 5 0 AMP BOARD IC103 POWER AMP IC B/D HP BOARD CW101 (Page 33)
  • Page 37: Schematic Diagram - Power Section (E3, Sp, Th Model)

    HCD-SV2D Ver. 1.1 7-14. SCHEMATIC DIAGRAM — POWER SECTION (E3, SP, TH MODEL) — 3 7 6 3 1 5 1 5 0 POWER BOARD (E3,SP,TH MODEL) POWER TRANS FORMER (MAIN) VOLTAGE SELECTOR MAIN BOARD CN301 (Page 28) 1 3 9 4 2 2 9 6 5 1 3...
  • Page 38: Schematic Diagram - Power Section (Us Model)

    HCD-SV2D Ver. 1.1 7-15. SCHEMATIC DIAGRAM — POWER SECTION (US MODEL) — 3 7 6 3 1 5 1 5 0 POWER BOARD (US MODEL) POWER TRANS FORMER (MAIN) MAIN BOARD CN301 (Page 28) 1.6A / 250V 1 3 9 4 2 2 9 6 5 1 3...
  • Page 39 HCD-SV2D 3 7 63 1515 0 • Waveforms – MAIN Board – – MPEG Board – IC501 ej (XT2) U707 <zcv (XIN) UD705 <zm/ (CVBS/C) 5.3 Vp-p 3.9 Vp-p 950 mVp-p 30.5 µ s 58.9 ns 1 V/DIV, 10 µ s/DIV 500 mV/DIV, 10 µ...
  • Page 40 HCD-SV2D Ver. 1.1 3 7 63 1515 0 • IC Block Diagrams – KEY Board – IC651 uPD16315GB-3BS Grid driver Multiplexed driver SEG19/GRID10 Command decoder LED1 SEG18/GRID11 LED2 Display memory LED3 SEG17/GRID12 24 bits x 12 words LED4 Timing generator...
  • Page 41 HCD-SV2D 3 7 63 1515 0 – MAIN Board – IC101 TDA7464 DIG_GND BASS_L1 R_OUT BASS_L0 L_OUT BASSO_R VAR_R RECOUT_R RECOUT_L L_IN4 BASS MIDDLE BASSO_L VAR_L TREBLE L_IN3 L 13942296513 L_IN2 SURR L_IN1 VREFOUT MIXING R_IN1 NETW2 MOVIE/ 400Hz...
  • Page 42 HCD-SV2D 3 7 63 1515 0 IC201 TA8142AP Vref1 Vref2 lref – MPEG Board – U706 LA6560-TE-L-E Thermal Shutdown Signal System GND S-GND (LOAD output voltage setting) VCONT L 13942296513 BTL-AMP Output VCC2 MUTE MUTE ON/OFF VLO- VIN4 VLO+...
  • Page 43 HCD-SV2D 3 7 63 1515 0 U709 LA9703W SREFI PDRF ISET XHTR 37DB 272P DCCUT 4.3K 30KHz LPF1 SREF LPF2 XHTR 150K 200KHz 30KHz FEEL WO/PP FIN1 SREF PREF SREF XHTR FEEL DPD/TE FIN2 SREF 200KHz PIN1 SREF RREC...
  • Page 44 HCD-SV2D 3 7 63 1515 0 U704 PCM1748E/2K 15 14 ZERO DETECT SYSTEM FUNCTION CLOCK OUTPUT AMP AND CONTROL MANAGER CONVERTER LOW-PASS FILTER INTERFACE 8 TIME OVER SAMPLING ENHANCED DIGITAL FILTER MULTI-LEVEL WITH SYSTEM DELTA-SIGMA FUNCTION CLOCK MODULATOR CONTROLLER...
  • Page 45 HCD-SV2D 3 7 63 1515 0 • IC Pin Function Description MAIN BOARD IC501 µPD78007 (SYSTEM CONTROLLER) Pin No. Pin Name Description RMUT Tuner muting signal output PMUT Tape PLAY muting signal output RPHD REC/PLAY control signal output BIAS...
  • Page 46 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description DSDA DAC encoder data signal output DSSTB DAC encoder chip enable signal output DSCK DAC encoder clock signal output — Not used E-STB Chip enable output to the microphone echo...
  • Page 47 HCD-SV2D 3 7 63 1515 0 MPEG BOARD UD705 ZR36748 (VIDEO DAC ENCODER) Pin No. Pin Name Description VDDP — Power supply terminal (+3.3V) DUPRD — Not used BOOTSEL2 — Not used GPCI014 LSI RST signal input from the AV decoder GPCI013 —...
  • Page 48 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description GNDP — Ground terminal 57 to 60 RAMADD4 to 7 Address bus to the D-RAM VDDP — Power supply terminal (+3.3V) 62 to 64 RAMADD8 to 11 Address bus to the D-RAM GNDP —...
  • Page 49 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description MEMDA14 Flash memory data bus MEMDA3 Flash memory data bus MEMDA15 Flash memory data bus MEMDA4 Flash memory data bus GNDP — Ground terminal MEMDA8 Flash memory data bus VDDP —...
  • Page 50 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description Y/R/V Video signal output C/B/V Video signal output DACGNDB — Ground terminal RSET Not used in this set. Fixed at (“L”). DACGNDDP — Ground terminal GPCIO18 SPDIF (DVD/CD) change signal output GNDP2 —...
  • Page 51 HCD-SV2D 3 7 63 1515 0 MPEG BOARD U707 LC78663N (AV DECODER) Pin No. Pin Name Description Motor Drive AMP signal output Motor Drive KFG signal input ADJV signal input PREC Reference signal input from the RF AMP RF PH...
  • Page 52 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description MRAS1B S-RAM low address strobe signal output 62 to 65 MA0 to 3 S-RAM address bus DVDD3 — Power supply terminal (+3.3V) DVSS — Ground terminal 68 to 72...
  • Page 53 HCD-SV2D 3 7 63 1515 0 Pin No. Pin Name Description VRPFR Not used in this set. Fixed at “H”. VCOCTL VPD signal input DVDD0 — Power supply terminal (+3.3V) DVSS — Ground terminal DVDD2 — Power supply terminal (+3.3V) System clock input (16.9344MHz)
  • Page 54: Exploded Views

    HCD-SV2D Ver. 1.1 SECTION 8 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • The mechanical parts with no reference The components identified by mark 0 or may have some difference from the original number in the exploded views are not supplied.
  • Page 55: Front Panel Section

    HCD-SV2D Ver. 1.1 3 7 63 1515 0 8-2. FRONT PANEL SECTION supplied supplied MIC boad inclueding Ref. No. 10 supplied L 13942296513 supplied HP boad inclueding Ref. No. 60 supplied Ref. No. Part No. Description Remark Ref. No.
  • Page 56: Chassis Section

    HCD-SV2D Ver. 1.1 3 7 63 1515 0 8-3. CHASSIS SECTION supplied supplied F901 PT901 supplied supplied supplied supplied supplied L 13942296513 supplied supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 9-885-079-96 POWER BOARD, COMPLETE (US)
  • Page 57: Dvd Mechanism Deck Section

    HCD-SV2D 3 7 63 1515 0 8-4. DVD MECHANISM DECK SECTION supplied supplied supplied L 13942296513 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 9-885-065-33 BELT (PULLEY) 9-885-059-40 WIRE (FLAT TYPE)(6 CORE) 9-885-065-34 DUMPER (TRAVERSE MECH)
  • Page 58: Electrical Parts List

    HCD-SV2D Ver. 1.1 SECTION 9 3 7 63 1515 0 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms.
  • Page 59 HCD-SV2D Ver. 1.1 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R316 1-259-033-91 RES, CARBON (SMALL) 1 C664 1-162-968-91 CAP,CHIP CERAMIC 4700PF B 1608 R317 1-259-033-91 RES, CARBON (SMALL) 1...
  • Page 60 HCD-SV2D Ver. 1.1 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R677 1-247-863-91 RES, CARBON (SMALL) 22K 9-885-077-14 MAIN BOARD, COMPLETE (US) R678 1-216-837-91 RES, 22K (1608) 9-885-079-75 MAIN BOARD, COMPLETE (SP,TH)
  • Page 61 HCD-SV2D Ver. 1.1 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C156 1-126-933-71 CAP, ELECT 100MF C232 1-164-315-91 CAP, CERAMIC 470PF CH (1608) C157 1-131-992-91 CAP, CERAMIC 100000PF F 1608...
  • Page 62 HCD-SV2D Ver. 1.2 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C402 1-126-959-91 CAP, ELECT 0.47MF (E3,SP,TH) C538 1-162-924-91 CAP, CERAMIC 56PF CH 1608 C403 1-126-964-91 CAP, ELECT 10MF (E3,SP,TH)
  • Page 63 HCD-SV2D Ver. 1.1 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC301 9-885-059-44 IC AP1501 Q317 8-729-200-75 TRANSISTOR 2SA1162G-TE85L IC401 6-702-896-01 IC BU9262AFS (E3,SP,TH) Q318 8-729-200-71 TRANSISTOR 2SC2712G-TE85L Q401...
  • Page 64 HCD-SV2D Ver. 1.1 MAIN 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R187 1-216-823-91 RES, CHIP 1.5K (1608) R306 1-247-835-91 RES, CARBON (SMALL) 1.5K R192 1-216-834-91 RES, CHIP 12K (1608) R309 1-216-993-91 RES, CHIP 2.4K (1608)
  • Page 65 HCD-SV2D Ver. 1.1 MAIN MPEG 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R419 1-216-815-91 RES, CHIP 330 (1608) (E3,SP,TH) R550 1-216-821-91 RES, CHIP 1K (1608) R552 1-216-821-91 RES, CHIP 1K (1608)
  • Page 66 HCD-SV2D Ver. 1.1 MPEG 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C715 1-164-156-91 CAP, CHIP CERAMIC 0.1MF F 1608 C808 1-104-660-71 CAP, ELECT 47MF C716 1-164-156-91 CAP, CHIP CERAMIC 0.1MF F 1608...
  • Page 67 HCD-SV2D MPEG 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CD725 1-104-660-71 CAP, ELECT 47MF CD814 1-164-390-91 CAP, CERAMIC 330PF CH 1608 CD726 1-104-660-71 CAP, ELECT 47MF CD819 1-164-156-91 CAP, CHIP CERAMIC 0.1MF F 1608...
  • Page 68 HCD-SV2D MPEG 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > R761 1-216-822-91 RES, 1.2K (1608) R762 1-216-829-91 RES, 4.7K (1608) L701 1-500-445-21 FERRITE, EMI (SMD) (2012) L702...
  • Page 69 HCD-SV2D Ver. 1.1 MPEG POWER 3 7 63 1515 0 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R846 1-216-800-91 RES, 18 (1608) RD802 1-216-817-91 RES, 470 (1608) R847 1-216-821-91 RES, 1K (1608) RND701 1-239-518-11 RESISTOR, NETWORK (1608)
  • Page 70 HCD-SV2D Ver. 1.1 POWER 3 7 63 1515 0 Ref. No. Ref. No. Part No. Part No. Description Description Remark Remark < RESISTOR > R901 1-247-789-91 RES, CARBON (SMALL) 18 1/8W 0 R902 1-219-237-11 RES,3.3M OHM 1/2W (US) < RELAY >...
  • Page 71 HCD-SV2D 3 7 63 1515 0 MEMO L 13942296513 u163 http://www.xiaoyu163.com...
  • Page 72 HCD-SV2D 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.

Table of Contents