Back Panel - Mitsubishi Electric WS-48515 Owner's Manual

Back Panel

11.
ANT-2
AUX
SERVICE IEEE1394
INPUT/OUTPUT
PORT
(DTV/CABLE /VHF/UHF)
–
1.
1. IEEE-1394 Input/Output
Use these jacks to connect the TV to external IEEE
1394 digital products by means of a single cable. There
are two jacks on the back panel for all models. For
WS-55615, WS-55615A, WS-65615, WS-65615A and
WS-73615 there is an additional jack on the front
panel. IEEE 1394 connections provide a high degree
of flexibility when connecting your NetCommand®
controlled system. Detailed information regarding IEEE
1394 connection requirements are in Chapter 4.
2. Antenna
(ANT-1 MAIN, ANT-2 AUX)
ANT-1 MAIN and ANT-2 AUX can each receive both
digital/analog over-the-air channels from a VHF/UHF
antenna or non-scrambled digital/analog cable
channels.
Your primary viewing signal source should be
connected to ANT-1 MAIN. ANT-1 MAIN must be
used to view premium subscription cable TV service
authorized by the CableCARD™ access card. The
CableCARD access card is provided by your local
cable company. ANT-2 AUX can continue to receive
over-the-air or non-scrambled cable signals.
10
ANT-1
MAIN
DIGITAL
AUDIO
CableCARD TM SLOT
–
2. 3. 4.
10.
INPUT MONITOR OUTPUT
1 2 AUDIO/VIDEO 1
COMPONENT
YPbPr (480i/480p/1080i)
1
DVI
Analog Audio
Digital Video
Digital Audio
5. 6.
3. Digital Audio Output
This output will automatically send Dolby® Digital audio
from digital channels, IEEE 1394 devices and HDMI™
(not DVI) signals to a digital Audio/Video receiver.
Connect this output to the A/V receiver's coaxial digital
audio input. This output will automatically turn off when
viewing an analog channel or device. Use Monitor
Ouput Audio 2 to send analog signals to your A/V
receiver.
Some digital cable channels send MPEG-1 digital audio
instead of Dolby Digital, however, not all A/V receivers
can decode MPEG-1 digital audio. This can cause the
A/V receivers to produce a loud noise that can damage
speakers. For this reason, the TV will automatically
turn off the digital audio output when tuned to a
channel or device that has MPEG-1 digital audio and
send it to the A/V receiver as analog left and right audio
from Monitor Output. You can enable the digital output
to include MPEG-1 digital audio if your A/V receiver
is capable of decoding it. See Edit NetCommand for
details.
4. CableCARD™ Slot
The CableCARD access card provided by your cable TV
service provider is inserted into this slot. CableCARD
9.
AUDIO 2
S-VIDEO
VIDEO
AUDIO-
LEFT/
(MONO)
IR EMITTER
NetCommand
R
AUDIO-
RIGHT
2
SERVICE WARNING
CAUTION:
TO MEASURE SECOND
Y
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
Pb
EXTERNAL GROUND.
WARNING:
HANDLE WITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
Pr TO HANDLE. REFER SERVICING TO
Q U A L I F I E D S E R V I C E P E R S O N N E L .
REPLACE WITH A TUBE OF THE SAME
AUDIO-
TYPE NUMBER FOR CONTINUED SAFETY.
LEFT/
X-RAY PRECAUTION:
THIS PRODUCT
(MONO)
I N C L U D E S C R I T I C A L M E C H A N I C A L
AND E LE CT RICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATION SAFETY.
AUDIO-
F O R C O N T I N U E D S A F E T Y R E P L A C E
RIGHT
C R I T I C A L C O MP O N E N T S I N D I C AT E D
IN THE SERVICE MANUAL ONLY WITH
E X ACT R E PLA CE ME NT PA R T S GI V E N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MINIMUM BRIGHTNESS, MEASUREMENT
PROCE DURE S AND PR OPE R SE RV ICE
ADJUSTMENTS.
7.
8.