Mitsubishi Electric LT-3280 Owner's Manual page 96

Chapter 7: Troubleshooting and Support
24. The TV Audio icon or A/V Receiver icon is
grayed out and not selectable.
25. Devices are grayed out in the Device Selection
menu or the PIP Selection menu.
26. Cannot see the A/V Receiver menu.
27. Screen is black when trying to view digital
channels or IEEE 1394 device.
28. The REC button is not working, or, on the
Transport menu the record key is grayed out and
not available.
29. Excessive digital artifacts.
30. DVCR analog/digital problems.
31. D-VHS recordings for digital cable have drop-
outs (loss of picture or sound), or no playback.
32. There is no audio and video from the IEEE 1394
device.
33. The IEEE 1394 Device is not listed in the Device
Selection menu.
34. The IEEE 1394 device cannot be selected.
35. DEVICE MENU button does not display a menu.
90
Problem Possible Solution
• Select the Change setting from the Edit NetCommand menu, and
then select the device (for example VCR). Once the Connection
screen is displayed, check if the audio checkbox is selected for the
TV input and/or AVR input.
• Verify the connections and NetCommand setup for the A/V receiver and the
desired source device, if any. See the instructions for item 23, previous page.
• A recording is in progress requiring the use of Monitor Out. Cancel
the recording to select the device.
• Digital channels and media cards cannot display in the PIP or POP.
• The A/V Receiver is not connected to any input of the media center.
To check the A/V Receiver menu temporarily plug into an unused
input of the media center. Then select Review from the NetCommand
Menu, turn the input On to view the A/V Receiver menu.
• The PerfectColor™ color balance has been incorrectly set. Use the
Setup menu to reset the color balance.
• The device does not support recording, such as a DVD player.
• Recordings can not be initiated from the Transport menu when
using an IEEE 1394 device. Press REC instead. The Record
menu displays allowing setup of a recording.
• The IEEE 1394 cable is too long (15 feet between devices is the
maximum length).
• There may be a slow device in the middle of the IEEE 1394 network.
Move the slow devices to the end so that connections for faster
devices do not pass through them.
• If the tape is currently playing but no picture displays, there may be a
mismatch of the media with the display. Press DEVICE to
display the Device Selection menu. Press ENTER for the DVCR
device. If digital is selected, try analog, or if analog is selected, try
digital.
• Digital cable signals on IEEE 1394 can exceed the data rate
standards supported by DVCR.
• The device is not turned on - turn the device power on.
• No media (tape or disc) is inserted into the device.
• The media is blank (has no recording).
• The play command failed - Try pressing play again on the device's
remote control or front panel.
• The device is already in use (for example: the device is currently
recording).
• The source is copy-protected or violates copy protection.
• The device's digital video signal is not supported by the TV, such as
DV video, common with camcorders. Use analog connections
instead, if available.
• The device is not an audio/video device.
• Too many other devices are already communicating over IEEE 1394.
Remove or stop some devices and try again.
• The device is unchecked in the Review screen. Select the
NetCommand menu. Through Review, verify the device is checked.
• The IEEE 1394 plug is disconnected or loose.
• The IEEE 1394 Device has not been powered On. Turn on.
• The device has not been discovered.
• The device is not an Audio/Video device.
• The device may be busy, either recording or a peer-to-peer
connection has been established. Cancel the recording or
peer-to-peer connection.
• The IEEE 1394 device does not provide a menu.
• The TV cannot support IEEE 1394 menus. See page 32.