Specifications; Specific Safety Rules - Makita DP3002 Instruction Manual

ENGLISH
1 Tighten
2 Chuck key
3 Sleeve
4 Ring
5 Switch trigger
6 Lock lever

SPECIFICATIONS

Model
Capacities
Steel ............................................. 10 mm
Wood ............................................ 32 mm
–1
No load speed (min ) ..................... 0 – 1,200
Overall length .................................. 304 mm
Net weight ........................................ 2.0 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the opeator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
8. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
Explanation of general view
7 Reversing switch lever
8 Side grip
9 Protrusions
10 Teeth
11 Loosen
12 Depth gauge
DP3002 DP3003
10 mm
32 mm
0 – 1,200
296 mm
1.8 kg
GEB001-2
13 Reaction
14 Reverse
15 Forward
16 Holding against a stud.
17 Holding against a floor.
18 Hook
DP4000 DP4001
13 mm 13 mm
38 mm 38 mm
0 – 900 0 – 900
304 mm 308 mm
2.2 kg 2.0 kg
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip, bit
or other accessories.
Installing or removing drill bit
For DP3002, DP4000, DP4002 (Fig. 1)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly. To remove the bit,
turn the chuck key counterclockwise in just one hole,
then loosen the chuck by hand. After using the chuck key,
be sure to return it to the original position.
For DP3003, DP4001, DP4003 (Fig. 2)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as it
will go. Hold the ring firmly and turn the sleeve clockwise
to tighten the chuck. To remove the bit, hold the ring and
turn the sleeve counterclockwise.
Switch action (Fig. 3)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
For continuous operation, pull the trigger and then push
the lock lever upward. To stop the tool from the locked
position, pull the trigger fully, then release it.
DP4002 DP4003
13 mm 13 mm
38 mm 38 mm
0 – 600 0 – 600
304 mm 308 mm
2.2 kg 2.0 kg
5