1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Grinder
  5. DWE4884
  6. Original instructions manual

DeWalt DWE4884 Original Instructions Manual

Die grinder
Hide thumbs Also See for DWE4884:
Table of Contents

Advertisement

Quick Links

DWE4884

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWE4884

Summary of Contents for DeWalt DWE4884

  • Page 1 DWE4884...
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Figure 1 Figure 2 Figure 3...
  • Page 4 Figure 4 10 mm max. 10 mm max. 10 mm max. 10 mm max.

  • Page 5: Technical Data

    ENGLISH DIE GRINDER DWE4884 An estimation of the level of exposure to Congratulations! vibration should also take into account You have chosen a D WALT tool. Years of the times when the tool is switched off experience, thorough product development and...

  • Page 6: General Power Tool Safety Warnings

    ENGLISH These products also comply with Directive is an increased risk of electric shock if your 2004/108/EC and 2011/65/EU. For more body is earthed or grounded. information, please contact D WALT at the following Do not expose power tools to rain or wet address or refer to the back of the manual.

  • Page 7: Additional Specific Safety Rules

    ENGLISH parts. Loose clothes, jewellery or long hair ADDITIONAL SPECIFIC SAFETY RULES can be caught in moving parts. If devices are provided for the connection Safety Instructions for All Operations of dust extraction and collection facilities, a) This power tool is intended to function ensure these are connected and properly as a grinder.

  • Page 8: Further Safety Instructions For All Operations

    ENGLISH the power tool at maximum no-load speed q) Do not run the power tool while carrying it at for one minute. Damaged accessories will your side. Accidental contact with the spinning normally break apart during this test time. accessory could snag your clothing, pulling the accessory into your body.

  • Page 9: Residual Risks

    ENGLISH rotating accessory and cause loss of control or match the mounting hardware of the power tool kickback. will run out of balance, vibrate excessively and may cause loss of control. c) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades Residual Risks create frequent kickback and loss of control.

  • Page 10: Electrical Safety

    ENGLISH Description (fi g. 1) When using a cable reel, always unwind the cable completely. WARNING: Never modify the power tool or any part of it. Damage or ASSEMBLY AND ADJUSTMENTS personal injury could result. WARNING: To reduce the risk of a.

  • Page 11: Operation

    ENGLISH OPERATION forth with moderate pressure. In this manner, the workpiece will not become too hot, does not discolour Instructions for Use (fi g. 3) and no grooves are formed. WARNING: Always observe the safety WARNING: Grasp tool firmly with both instructions and applicable regulations.

  • Page 12: Maintenance

    ENGLISH 2. Loosen the collet nut (c) with the 17 mm brush assemblies are available at your local service wrench (e) by turning it counterclockwise. center. 3. Insert the shank of the accessory (minimum 20mm) into the collet. 4. Securely tighten the collet nut (c) using the spanner provided.
  • Page 13 ENGLISH Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.
  • Page 14 ENGLISH...
  • Page 16 Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia • 1800 338 002 (Aust) or 0800 339 258 (NZ) www.dewalt.com.au • www.dewalt.co.nz (MAR14) DWE4884-XE Copyright © 2014 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

Table of Contents