1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Grinder
  5. DWE4036
  6. Original instructions manual

DeWalt DWE4036 Original Instructions Manual

Hide thumbs Also See for DWE4036:
Table of Contents

Advertisement

Quick Links

Download this manual
DWE4036

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWE4036

Summary of Contents for DeWalt DWE4036

  • Page 1 DWE4036...
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A Fig. B...
  • Page 4 Fig. C Fig. D Fig. E1 Fig. E2 Fig. G Fig. F...
  • Page 5 Fig. I Fig. H...

  • Page 6: Technical Data

    English SMALL ANGLE GRINDER DWE4036 Congratulations! noise emission may differ. This may significantly increase the exposure level over the total working period. You have chosen a IRWIND WALT tool. Years of experience, An estimation of the level of exposure to vibration and/...

  • Page 7: Definitions: Safety Guidelines

    Failure to follow all instructions listed below Small Angle Grinder may result in electric shock, fire and/or serious injury. DWE4036 SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE WALT declares that these products described under “technical data”...

  • Page 8: Additional Specific Safety Rules

    English non‑skid safety shoes, hard hat or hearing protection used performed. Use of the power tool for operations different for appropriate conditions will reduce personal injuries. from those intended could result in a hazardous situation. c ) Prevent unintentional starting. Ensure the switch h ) Keep handles and grasping surfaces dry, clean and is in the off position before connecting to power free from oil and grease.

  • Page 9: Kickback And Related Warnings

    English maximum no‑load speed for one minute. Damaged point can dig into the surface of the material causing the wheel accessories will normally break apart during this test time. to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s i ) Wear personal protective equipment.

  • Page 10: Additional Safety Instructions For Wire Brushing Operations

    English reducing the possibility of wheel breakage. Flanges beyond the sanding pad presents a laceration hazard and for cut‑off wheels may be different from grinding may cause snagging, tearing of the disc or kickback. wheel flanges. Additional Safety Instructions for Wire f ) Do not use worn down wheels from larger power Brushing Operations tools.

  • Page 11: Package Contents

    English Package Contents DANGER: Do not use for wood cutting or woodcarving. Do not use toothed blades of any kind. Serious injury The package contains: can result. 1 Angle grinder These heavy‑duty angle grinders are professional power tools. 1 Cutting Guard DO nOT let children come into contact with the tool.
  • Page 12 English Flanges and Wheels nOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose; 6 mm Mounting Non‑Hubbed Wheels (Fig. D, E1, E2) thick wheels are designed for surface grinding while thinner WARNING: Failure to properly seat the flange/ clamp nut/ Type 27 wheels need to be examined for the manufacturer's wheel could result in serious injury (or damage to the tool label to see if they can be used for surface grinding or only edge...

  • Page 13: Prior To Operation

    English 5. Tighten the clamp nut by hand. Then depress the spindle inspecting and installing an accessory, position yourself and lock button while turning the sanding disc until the sanding bystanders away from the plane of the rotating accessory disc and clamp nut are snug. and run the power tool at maximum no‑load speed for one minute.
  • Page 14 English Proper Hand Position (Fig. G) 1. Allow the tool to reach full speed before touching the tool to the work surface. WARNING: To reduce the risk of serious personal injury, 2. Apply minimum pressure to the work surface, allowing ALWAYS use proper hand position as shown. the tool to operate at high speed.

  • Page 15: Cutting Metal

    English Environmental safety If the power supply is shut off by the RCD, take the tool to an authorised D WALT repair agent. 1. Paint should be removed in such a manner as to minimise the amount of dust generated. WARNING: In extreme working conditions, conductive dust can accumulate inside the machine housing when 2.

  • Page 16: Accessories Chart

    English Pop‑off Brushes Accessories Chart The motor will be automatically shut off indicating that the Max. Min. Periphical Threaded hole [mm] [mm] Rotation speed length carbon brushes are nearly worn out and that the tool needs [min. [m/s] [mm] servicing. The carbon brushes are not user‑serviceable. Take the tool to an authorised D WALT repair agent.
  • Page 17 English Additional information for guards and Accessories ≤10 mm When using segmented diamond wheels, use only diamond wheels with a peripheral gap not greater than 10 mm and negative rake angle. DO NOT USE segmented diamond wheels with a peripheral gap greater than 10 mm and/or a positive rake angle.
  • Page 18 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type B Type B  guard Guard Backing flange Flap wheel Type 27 depressed centre wheel Wire wheels Threaded locking flange Type B guard Wire wheels with threaded nut Wire wheel Type B  guard...
  • Page 19 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type A Type A guard Guard Metal cutting disc, bonded Backing flange Type A Guard Diamond cutting Cutting wheel wheels Threaded locking flange No guard Wire cup with threaded nut...
  • Page 20 Belgique et WALT ‑ Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

Table of Contents