Reset Button - Sony XR-CA350X Service Manual

XR-CA350X
4 1
5
3
Orient the release key
correctly.
Orientez correctement
la clé de déblocage.
5 1
1 8 2
m m
1
6 A
TOYOTA
max. size
2
5 × 8 mm
×
( 7 / 11 / in)
32 32
Dimensions
max. 5 × 8 mm
×
( 7 / 11 / po)
32 32
Bracket
Support
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
7 A
(RELEASE)
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
6
2
c
2
5 3 m
m
Claws
Griffes
to dashboard/center console
vers le tableau de bord/la console centrale
2
max. size
5 × 8 mm
×
( 7 / 11 /
32 32
Dimensions
max. 5 × 8 mm
×
Bracket
( 7 / 11 /
32 32
Support
(OFF)
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 3 and the bracket 1 from
the unit.
1
Remove the protection collar 3.
1 Engage the release keys 5 together with
the protection collar 3 .
2 Pull out the release keys 5 to remove the
protection collar 3.
2
Remove the bracket 1.
1 Insert both release keys 5 together
between the unit and the bracket until
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 3 are properly engaged in the slots of the
unit (5-3).
5
Face the hook
inwards.
1
Tournez le crochet
vers l'intérieur.
3
B
NISSAN
max. size
2
5 × 8 mm
×
( 7 / 11 / in)
32 32
Dimensions
max. 5 × 8 mm
×
( 7 / 11 / po)
32 32
in)
po)
B
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 2.
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (RELEASE), then slide the
front panel a little to the left, and pull it off
towards you.
7-B To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
c c
Dashboard
Tableau de bord
1
3
to dashboard/center console
vers le tableau de bord/la console centrale
2
Bracket
Support
Bracket
Support
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.

RESET button

When the installation and connections are
completed, be sure to press the RESET button
with a ball-point pen, etc., after detaching the
front panel.
max. size
5 × 8 mm
×
( 7 / 11 / in)
32 32
Dimensions
max. 5 × 8 mm
×
( 7 / 11 / po)
32 32